VBar NEO for external transmitters
Helico helicopters with NEO that still fly without VBar Control
| Subject | Views | Posts | Last post |
|---|---|---|---|
| How to disable governor on an electric helicopter translated by zamuel_a | Views: 0 | Posts: 8 |
1 August 2016 15:4001.08.2016 15:40 by zamuel_a |
| Align RPM Sensor translated by romsch | Views: 0 | Posts: 5 |
29 July 2016 13:1529.07.2016 13:15 by romsch |
| How to disable Governor? translated by MarkB | Views: 0 | Posts: 8 |
29 July 2016 12:5729.07.2016 12:57 by RV |
| Neo can no longer be initialized. translated by Roland66 | Views: 0 | Posts: 5 |
27 July 2016 05:5127.07.2016 05:51 by RV |
| Software could not be activated. translated by Cadderly | Views: 0 | Posts: 3 |
26 July 2016 13:1826.07.2016 13:18 by Cadderly |
| Neo cannot be switched to Rescue mode. translated by peters | Views: 0 | Posts: 2 |
23 July 2016 10:1323.07.2016 10:13 by RV |
| how do i calibtate the cc160hv to the neo using a dx9 by markb75 | Views: 0 | Posts: 2 |
23 July 2016 08:1523.07.2016 08:15 by RV |
| Nitro Servo Setup translated by James | Views: 0 | Posts: 8 |
22 July 2016 08:2922.07.2016 08:29 by Eddi E. aus G. |
| Firmware Update translated by fastflyer20 | Views: 0 | Posts: 2 |
18 July 2016 19:1818.07.2016 19:18 by RV |
| So far, 5.3, thoughts on NEO. translated by Phil S. | Views: 0 | Posts: 7 |
18 July 2016 16:5918.07.2016 16:59 by Phil S. |
| governor gain question - chirping sound when under load translated by ReadyToFly | Views: 0 | Posts: 10 |
15 July 2016 21:1215.07.2016 21:12 by RV |
| DX8 Hold Switch - Vstabi Neo? translated by shredman | Views: 0 | Posts: 9 |
15 July 2016 11:4215.07.2016 11:42 by shredman |
| External 2S Lipo connected to VBar as BEC support translated by Realplutonium | Views: 0 | Posts: 17 |
14 July 2016 18:3114.07.2016 18:31 by Realplutonium |
| Mac Neosoftware translated by Dirk S | Views: 0 | Posts: 23 |
13 July 2016 10:4713.07.2016 10:47 by Dirk S |
| NEO non VLink and BK 8002 servos translated by weracemo | Views: 0 | Posts: 12 |
12 July 2016 06:1412.07.2016 06:14 by RV |
| Gaui X3 - Rear end flips out? translated by shredman | Views: 0 | Posts: 7 |
11 July 2016 10:2111.07.2016 10:21 by Eddi E. aus G. |
| RPM port translated by mgaproduction | Views: 0 | Posts: 4 |
10 July 2016 20:4410.07.2016 20:44 by mgaproduction |
| The Neo board slips inside the housing when plugged in. translated by picpassion | Views: 0 | Posts: 2 |
9 July 2016 22:3609.07.2016 22:36 by RV |
| The rear end swings during a backflip. translated by pepekra | Views: 0 | Posts: 5 |
8 July 2016 18:2108.07.2016 18:21 by RV |
| Additional sensor translated by BOcnc | Views: 0 | Posts: 4 |
5 July 2016 19:3205.07.2016 19:32 by BOcnc |
| NEO and Spektrum DX8 : some problems translated by mgaproduction | Views: 0 | Posts: 18 |
4 July 2016 22:2004.07.2016 22:20 by mgaproduction |
| Problem with Gov. translated by Rolf | Views: 0 | Posts: 7 |
3 July 2016 21:0603.07.2016 21:06 by RV |
| Information - Neo & YGE 120? translated by shredman | Views: 0 | Posts: 4 |
1 July 2016 08:5301.07.2016 08:53 by Eddi E. aus G. |
| AUX2/AUX3 questions regarding signal output (SBUS receiver) translated by janK | Views: 0 | Posts: 5 |
29 June 2016 21:2729.06.2016 21:27 by janK |
| YGE 160 HV start-up torque translated by CarstenH | Views: 0 | Posts: 10 |
28 June 2016 21:5928.06.2016 21:59 by RV |