VBar NEO for external transmitters
Helico helicopters with NEO that still fly without VBar Control
| Subject | Views | Posts | Last post |
|---|---|---|---|
| PHT-2 Neo and extra sensor translated by WFEGb | Views: 0 | Posts: 4 |
24 May 2016 00:3024.05.2016 00:30 by WFEGb |
| Maneuverability too low... translated by Tim V | Views: 0 | Posts: 6 |
23 May 2016 20:5523.05.2016 20:55 by RV |
| Setup recommendation Diabolo 550 translated by Franky138 | Views: 0 | Posts: 2 |
22 May 2016 07:2722.05.2016 07:27 by RV |
| Learning Graupner Hott controllers translated by PitchOrDie | Views: 0 | Posts: 3 |
21 May 2016 21:5521.05.2016 21:55 by PitchOrDie |
| Neo gets stuck during initialization translated by Baldi | Views: 0 | Posts: 7 |
19 May 2016 15:1519.05.2016 15:15 by RV |
| Event log: Critical 0:05 IMU sensor error translated by hilmar.theiss@web.de | Views: 0 | Posts: 2 |
18 May 2016 21:5518.05.2016 21:55 by RV |
| RC input package translated by Matthias1983 | Views: 0 | Posts: 2 |
18 May 2016 10:4418.05.2016 10:44 by RV |
| New here translated by uboot | Views: 0 | Posts: 2 |
17 May 2016 09:1317.05.2016 09:13 by Eddi E. aus G. |
| Macrocells with VBar NEO and third-party receiver/transmitter possible? translated by Husi | Views: 0 | Posts: 13 |
11 May 2016 12:0411.05.2016 12:04 by Eddi E. aus G. |
| Pirouettes incorrectly compensated? translated by OliP | Views: 0 | Posts: 19 |
11 May 2016 06:0311.05.2016 06:03 by RV |
| Problems with VBar software translated by Kurvenkratzer | Views: 0 | Posts: 10 |
10 May 2016 22:1310.05.2016 22:13 by Kurvenkratzer |
| Rear-end optimizers - how to use them correctly. translated by pepekra | Views: 0 | Posts: 8 |
10 May 2016 06:0810.05.2016 06:08 by pepekra |
| NEO - Mac Version - Setup "cyclic" - Position 2 does not switch translated by topgun | Views: 0 | Posts: 3 |
9 May 2016 09:5509.05.2016 09:55 by Eddi E. aus G. |
| Setting in the Wizard for tail servo translated by Realplutonium | Views: 0 | Posts: 5 |
9 May 2016 06:1509.05.2016 06:15 by Realplutonium |
| Neo dead? translated by PitchOrDie | Views: 0 | Posts: 4 |
8 May 2016 17:5308.05.2016 17:53 by Master FBL |
| Jive Pro with bailout and 3 speeds translated by Schorsch | Views: 0 | Posts: 4 |
8 May 2016 11:4108.05.2016 11:41 by ikarus991 |
| Neo does not recognize RX Sat translated by Bianca | Views: 0 | Posts: 5 |
8 May 2016 09:5708.05.2016 09:57 by Bianca |
| VBar Neo exhibits strange behavior after initialization translated by Homer Simson | Views: 0 | Posts: 4 |
6 May 2016 22:2206.05.2016 22:22 by Homer Simson |
| Only two benches are in use translated by steveman | Views: 0 | Posts: 3 |
6 May 2016 20:5306.05.2016 20:53 by steveman |
| NEO + YGE 120 HV in the logo 690 SX translated by KKCE | Views: 0 | Posts: 4 |
6 May 2016 08:3306.05.2016 08:33 by RV |
| What does the VBar Governor do during Lipo cell number changes? translated by Kurvenkratzer | Views: 0 | Posts: 3 |
4 May 2016 22:0704.05.2016 22:07 by Kurvenkratzer |
| Neo to M-Link / BD translated by jofly_48 | Views: 0 | Posts: 3 |
4 May 2016 20:1804.05.2016 20:18 by jofly_48 |
| NEO Pro - Setup - Parameters tail rotor translated by topgun | Views: 0 | Posts: 6 |
2 May 2016 17:0802.05.2016 17:08 by RV |
| VBar Neo, no Windows 10??? translated by helitom67 | Views: 0 | Posts: 4 |
2 May 2016 09:0402.05.2016 09:04 by RV |
| File Save translated by Kimo | Views: 0 | Posts: 3 |
1 May 2016 20:1801.05.2016 20:18 by Kimo |