zamuel_a
1 August 2016 12:1201.08.2016 12:12
I have a T-REX 500 with a Futaba T18SZ radio and I used an older (not VBAR) FBL controller but wanted to try the VBAR NEO so I installed that. I think I have got everything working except the throttle control. I don't have a governor but have throttle curves for all modes (normal, idle up...) in the radio. I can't get that to work with the NEO. What happens now is that when I push the throttle I get full speed on the motor, so I have either nothing or full speed!
I read something about AUX3 control and saw the description for a Futaba radio, but they connected the throttle to a swith, not the throttle lever. I guess this is when using a governor, but is it possible to use the NEO without one?
Eddi E. aus G.
1 August 2016 12:2301.08.2016 12:23
Hi,
please check out the
FAQ, last entry.
Kind regards
Eddi
Born to fly ...
forced to work.
RV
1 August 2016 12:2301.08.2016 12:23
Using AUX3 we just pass the throttle from the selected channel to the output when "external Gov" is selected.
So this can be used for every electric helicopter which does not use our gov. It can't be used for nitros (servo) due the failsafe handling.
The failsafe (if we won't get data from the SBus, e.g. cable fell off) is "no pulse" which turns off the motor usually (check). The secondary FS between TX and RX must be set by the pilot too of course as usual.
But - which ESC is installed? - Maybe it would be a small task to get it Gov'ed ;-)
BTW: keep also in mind you have to program a channel which gives us the correct "Motor" status for some changes in the controls during Motor off, ar and run.
I'd change the T14 to a VBar Control and use our Gov ;-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
1 mal bearbeitet. Zuletzt am 01.08.2016 12:26 von RV.
zamuel_a
1 August 2016 13:1001.08.2016 13:10
So I should remove the cable from the ESC input on the NEO and connect to AUX3 instead?
" and that you should assign an additional channel to the Motor Switch, which is operated together with the throttle settings. "
What motor switch? I just use the regualar lever on the TX to control the motor
1 mal bearbeitet. Zuletzt am 01.08.2016 13:12 von zamuel_a.
Eddi E. aus G.
1 August 2016 14:0201.08.2016 14:02
Hi,
the VBar expects it's internal logic of handling throttle to be met.
Means, we have a motor switch to switch between three states OFF-IDLE-ON and usually a Flight-Mode/Condition//Bank Switch to switch between three head speeds.
If you want to bypass the logic, we recommend you still actuate the motor switch function with a spare channel and a mixer so the VBar gets info if the model is powered or not, for once to log this info and to adapt the control loop accordingly (see FAQ).
So you would use your lever to control the motor and at the same time output the necessary values on a second channel which you assign to the motor channel.
Kind regards
Eddi
Born to fly ...
forced to work.
zamuel_a
1 August 2016 14:3201.08.2016 14:32
ok, but I don't understand how to connect it. Now I have the ESC connected to ESC on NEO, The receiver uses S-BUS and one cable connected to AUX1.
What else should I connect?
Eddi E. aus G.
1 August 2016 15:1801.08.2016 15:18
Hi,
well, either you follow the NEO logic, then ESC to ESC and SBus to AUX 1, and setup with a motor switch and a bank switch according to the FAQ.
The RPM wire of the ESC (or an extra brushless phase sensor's wire) goes into RPM if you want to use the VBar Governor.
Or you bypass the NEO, then ESC to AUX 3, throttle channel number to AUX 3 in the VBar Setup so you have direct throttle control from the radio, and a mixer to actuate the motor switch positions OFF (when the model is no powered) or ON (when the model is powered).
Kind regards
Eddi
Born to fly ...
forced to work.
zamuel_a
1 August 2016 15:4001.08.2016 15:40
That seems to be working! Thanks for the help. Now I just have to get out and try it ;-)