VBar NEO for external transmitters
Helico helicopters with NEO that still fly without VBar Control
| Subject | Views | Posts | Last post |
|---|---|---|---|
| JR servos on the NEO translated by BunGeee | Views: 0 | Posts: 16 |
21 August 2015 22:4221.08.2015 22:42 by RV |
| VBar NEO (non VLink) important information translated by Eddi E. aus G. | Views: 0 | Posts: 1 |
21 August 2015 12:4621.08.2015 12:46 by Eddi E. aus G. |
| PC software error translated by kai123 | Views: 0 | Posts: 2 |
20 August 2015 15:2320.08.2015 15:23 by Eddi E. aus G. |
| Help with error analysis - Unusual log entries during a crash translated by fabfour | Views: 0 | Posts: 4 |
20 August 2015 12:4420.08.2015 12:44 by fabfour |
| Program Neo with VBC and then use it with S-Bus translated by mfink@freenet.de | Views: 0 | Posts: 9 |
19 August 2015 20:0319.08.2015 20:03 by RV |
| Question about enabling failsafe for AUX2 and AUX3 translated by ikarus991 | Views: 0 | Posts: 3 |
19 August 2015 01:3619.08.2015 01:36 by ikarus991 |
| Not below 1800 rpm with Neo control translated by romikado | Views: 0 | Posts: 8 |
18 August 2015 21:0018.08.2015 21:00 by RV |
| Neo and Throttle Curve translated by rwilabee | Views: 0 | Posts: 29 |
18 August 2015 20:0118.08.2015 20:01 by RV |
| Vbar NEO Yaw rate too slow and External ESC help needed translated by Mike Wilson | Views: 0 | Posts: 8 |
17 August 2015 22:3717.08.2015 22:37 by RV |
| VBar Neo driver installation translated by Bolli | Views: 0 | Posts: 6 |
17 August 2015 18:0417.08.2015 18:04 by RV |
| NEO + Spektrum DX-7 + Kontronik Jive 80 HV translated by Gyrofreak | Views: 0 | Posts: 7 |
17 August 2015 13:1317.08.2015 13:13 by Tomster |
| Rescue experience translated by stefan_heli | Views: 0 | Posts: 14 |
17 August 2015 09:1317.08.2015 09:13 by Eddi E. aus G. |
| PC Software: Swashplate servos locked translated by TeaRex | Views: 0 | Posts: 2 |
16 August 2015 20:1316.08.2015 20:13 by RV |
| External controller does not initialize translated by TeaRex | Views: 0 | Posts: 17 |
16 August 2015 17:3916.08.2015 17:39 by RV |
| Should I connect the speed sensor? Is the regulator sufficient? translated by DJBlue | Views: 0 | Posts: 7 |
16 August 2015 09:4116.08.2015 09:41 by DJBlue |
| Vstabi Neo Rescue Analysis translated by Paprika1972 | Views: 0 | Posts: 18 |
16 August 2015 09:3516.08.2015 09:35 by RV |
| rescue speed advice translated by ragge1 | Views: 0 | Posts: 6 |
15 August 2015 20:0615.08.2015 20:06 by RV |
| Saving the setup translated by TeaRex | Views: 0 | Posts: 2 |
15 August 2015 15:0115.08.2015 15:01 by RV |
| Re: Pro Update and YGE 90 LV controller - video tutorial translated by UdoP | Views: 0 | Posts: 4 |
15 August 2015 11:5015.08.2015 11:50 by RV |
| Neo non-VLink availability translated by Tomster | Views: 0 | Posts: 7 |
15 August 2015 11:4115.08.2015 11:41 by Tomster |
| Problem with setting up Neo translated by Björn | Views: 0 | Posts: 5 |
15 August 2015 08:4615.08.2015 08:46 by Björn |
| No connection to the Neo translated by Proto | Views: 0 | Posts: 5 |
14 August 2015 10:3314.08.2015 10:33 by Eddi E. aus G. |
| NEO VLink+Gyro or NEO VLink translated by rutra | Views: 0 | Posts: 2 |
13 August 2015 00:5413.08.2015 00:54 by RV |
| L/S with NEO, VBar Control and Spectrum translated by Lastnio | Views: 0 | Posts: 5 |
11 August 2015 20:4411.08.2015 20:44 by RV |
| Hyperion speed sensor no longer available? translated by md520n | Views: 0 | Posts: 16 |
10 August 2015 23:2910.08.2015 23:29 by RV |