Björn
13 August 2015 21:4513.08.2015 21:45
Hello!
I have Neo, futaba 18mz and kontronik kosmik 160A. Can you please help me to setup tx channels on my futaba? I wouldlike to know which channel I put in tx to get governor to work, In pc software I dont get up the governor screen, I know its my own problem with my tx setting... Now I have channel:
1: Ail, 2: Elevator, 3: Aux3, 4: Rudder, 5: Aux5, 6: Pitch, 7 Aux7, 8: Aux8
My T.H switch is (SC) working on channel Aux3, Banks on Aux 5 Switch SB. Where do I set my governor?
I have Neo pro, not rescue.
I only have been flying cgy750 before and cant wait until I get my Urukay and Neo in air... :-) Please help me... :-) Best regards Björn
2 mal bearbeitet. Zuletzt am 13.08.2015 22:04 von Björn.
RV
13 August 2015 23:1313.08.2015 23:13
Using Kontronik - there is no Governor to set. Just give the needed Signal from TX to AUX3 (if Master is plugged in there) AND give us on the "Motor" input a signal for the Status off/run/Idle(AR) as requested anyway.
We recommend to plug the ESC to "ESC" and use the fixed % Values in the VBar as output per Bank/AR.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Björn
14 August 2015 19:3314.08.2015 19:33
Hello! Thanks for quick answer! :-) Now everything works out, just ned to set my headspeed. With this setting, is it possible to set the rpm from my tx? I have connect the "slave" to channel 3 on my rx 7008, and "master" to esc on neo, rx sbus to aux1 neo.
Best regards Björn
RV
14 August 2015 20:5214.08.2015 20:52
See here:
http://www.vstabi.info/en/neo_transmitter
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Björn
15 August 2015 08:4615.08.2015 08:46
Big thanx!
Now this will work great :-) I had my sbus to AUX 1 on Neo, read it on "Wiring your Neo", but now I know :-) Thanks again. Best regards Björn