← VBar NEO for external transmitters

Neo and Throttle Curve translated

VBar › VBar NEO for external transmitters · Started by rwilabee on 10 August 2015 19:2610.08.2015 19:26
rwilabee 10 August 2015 19:2610.08.2015 19:26
For now I don't really want a governor on my Acrobatic. Eventually I will set up my Stator Gator. My Setting in GovI are External ESC Gov and GovII Throttle Servo adjustment is on. If I turn it off my throttle doesn't work. My throttle servo is working backwards to the carburetor but on the Transmitter screen it shows it is moving correctly. If I change the direction in my radio it shows it working backwards in the transmitter screen but the servo direction doesn't change. How do I fix that. I'm assuming that after everything is working I will be able to set up Throttle Curves in my 14SG as I normally do.


Thanks
Rich



4 mal bearbeitet. Zuletzt am 10.08.2015 23:02 von rwilabee.
RV 10 August 2015 23:2710.08.2015 23:27
This setup way is supposed to support a electric ESC with internal gov. Flying with a nitro or gasser - use the VGov. You can also use the VGov w/o RPM sensor and so it uses the internal throttlecurves only - but makes alot of event log entries about the missing signals. This would be best to be prepared for later VGov.

As already state a few times - the TC is determined by Basic Throttle (Point 2), Basic Throttle + Coll. Ad (Point 1 and 3). In a spooluop bank (not mandatory needed) Point 1 is idle of course.

Another way wouls be to assign the throttle "channel" from TX to aux 1,2 or 3 - and do everything from TX. But do NOT forget to tell the Vbar when the motor is runninng or not (Motor Switch Status must be sent).

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
rwilabee 11 August 2015 00:2411.08.2015 00:24
I guess I still need some help. I was going to try your last suggestion so I assigned Channel Three to Aux 3 and assigned it to switch SG. In the transmitter screen when I switch SG it goes from Run to stop. If I plug the throttle servo into Aux 3 nothing happens no matter which way I switch SG. If I leave it plugged in to ESC it still moves but still not in the correct direction. Sorry to be such a pain.



1 mal bearbeitet. Zuletzt am 11.08.2015 00:32 von rwilabee.
RV 11 August 2015 13:1411.08.2015 13:14
Can you please check the PC Software for the latest version?

There was a bug inside at this point a few weeks ago.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
rwilabee 11 August 2015 14:5611.08.2015 14:56
The Software that I downloaded last week was 6.1.0 06.05.2015 then it says JRE:1.7.0_21OS:6.1 I just looked on the web site and it looks like there might be a new version 6.1.6. I downloaded it and it still says 6.1.0 I wonder if the download is not pointing at the latest software.

If it was working correctly would I plug the servo into ESC or Aux 3. What will I be looking for to be able to get that servo to reverse on throttle as you have the same heli as I do so you know the throttle arm moves toward the nose for high throttle which mine is not doing.

Thanks

Rich



4 mal bearbeitet. Zuletzt am 11.08.2015 15:46 von rwilabee.
RV 11 August 2015 16:2211.08.2015 16:22
You can reverse the servo - when you are using the VGov as it is supposed to be ;-)

Anyway - the signal sfrom AUX3 will be provided at AUX3 of course, what else.

Does AUX2 work?

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.




1 mal bearbeitet. Zuletzt am 11.08.2015 16:22 von RV.
rwilabee 11 August 2015 16:4011.08.2015 16:40
In the receiver screen I have the motor on 3

Aux 3 on 3

In my radio I don't have Aux 2 assigned to any channel

I've got it set up the like T8 sample.

At this point would it be easier to just go ahead and install the stator gator and not try to fly it the first time without it. If so which choice do I take in the Gov I and Gov II screens to make sure I get it correct. By the way if I put the stator gator in now do I leave all my settings in Function the same as or do I put the throttle back on 3 and remove Aux 3 from 3.

Is my version of the software ok?

Rich



2 mal bearbeitet. Zuletzt am 11.08.2015 16:52 von rwilabee.
RV 11 August 2015 18:1011.08.2015 18:10
Quote: In my radio I don't have Aux 2 assigned to any channel

I don't care about your radio and which channel which name and assignment has -. i just meant this assignement in the PC Software.

Just assign the Throttle channel from the TX to our output here. If Aux 3 doesn't work (as it seem to be - but after this completely confusing discussion her i am not sure) - Use Aux2.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.


rwilabee 11 August 2015 18:2311.08.2015 18:23
Ok I'm going to do that. After I take channel 3 in the radio and assign it to Aux 2 or 3 do I also assign a switch to it.
By the way my receiver is an 8 channel SBus. Is that enough channels in the receiver to do all of this.

Thanks

Rich



1 mal bearbeitet. Zuletzt am 11.08.2015 18:47 von rwilabee.
ulrich 11 August 2015 18:5211.08.2015 18:52
SBus usually transfers 16 Channels, independatn how many the reciver has. So there shall be plenty channels for this and spare.

so long ... Uli
http://www.vstabi.de
rwilabee 11 August 2015 18:5811.08.2015 18:58
Ok Now I seem to be getting somewhere. I assigned throttle channel 3 to Aux 3 and assigned J3 stick. I plugged the Throttle servo into Aux 3 and the servo is moving. On the receiver screen I can see Movement on Aux 3. So now I can see if I can get this working. On the Gov I screen I have told it Vbar Gov Nitro and I'm on Gov II screen when I turn on the throttle adjustment the low and high don't seem to move my throttle servo. I'm assuming this is where you adjust the throw for the servo. Also is this the only place you can adjust the throw on the Throttle Servo whether you are using a Gov or not. I may go ahead and just set up the Stator Gator for the first flight. I probably won't have the head speed screens you have on the Vbar Radio so I'll have to figure out how to do that.

Thanks

Rich



2 mal bearbeitet. Zuletzt am 11.08.2015 19:14 von rwilabee.
RV 11 August 2015 20:4511.08.2015 20:45
Yep - you can now set up your throttle diurect from TX as it was done since years.

Please disable the VGov now to avoid unintendend log entries.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
rwilabee 11 August 2015 21:4211.08.2015 21:42
Here is where I'm at. I disabled the VGov.

I have channel 3 assigned to Aux 3 and Switch SG so I can tell the Vbar that the engine is in the run mode. I have Channel 10 assigned to Thr and stick J3. The throttle servo is going in the correct direction and I can adjust the throttle end points in the radio on Channel 10 THR. It will also let me make a Throttle Curve so I'm in good shape.

Took the Heli out for a test spin and it is flying great with the Neo. If I go ahead and put in my Stator Gator do I leave all my work arounds the same in the Transmitter. Since I don't have a digital readout for head speed like your Vbar radio examples can you give me some idea where I would set up the Idle up 1, 2, & 3 head speeds in my Futaba. Would I also need to set up a bank for each flight mode?


Thanks for all the help you guys are great.

Rich



7 mal bearbeitet. Zuletzt am 12.08.2015 04:43 von rwilabee.
RV 12 August 2015 08:3912.08.2015 08:39
Quote:I have channel 3 assigned to Aux 3 and Switch SG so I can tell the Vbar that the engine is in the run mode. I have Channel 10 assigned to Thr and stick J3. The throttle servo is going in the correct direction and I can adjust the throttle end points in the radio on Channel 10 THR. It will also let me make a Throttle Curve so I'm in good shape.

:-) :-) :-)


Quote:Took the Heli out for a test spin and it is flying great with the Neo. If I go ahead and put in my Stator Gator do I leave all my work arounds the same in the Transmitter. Since I don't have a digital readout for head speed like your Vbar radio examples can you give me some idea where I would set up the Idle up 1, 2, & 3 head speeds in my Futaba. Would I also need to set up a bank for each flight mode?

I would just suggest to use the VBar Gov then - and copy my settings as start point from my article into the PC software (of course with your endpoints).

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
rwilabee 12 August 2015 14:0012.08.2015 14:00
So would I leave the setup below in the radio when I add the Stator Gator: Or do I go back to a standard setup in the radio and connect the throttle servo to the ESC port.

I have channel 3 assigned to Aux 3 and Switch SG so I can tell the Vbar that the engine is in the run mode. I have Channel 10 assigned to Thr and stick J3.

I am getting a little tail wag and I have the tail gyro gain down to 73. I haven't tried any further. Do you remember where you are running yours.

Thanks

Rich



2 mal bearbeitet. Zuletzt am 12.08.2015 23:58 von rwilabee.
RV 13 August 2015 00:5713.08.2015 00:57
When you run the SG - you have to use VBar Governor with all its needed settings. So your current radio setup is a temporary workaround - not more.

If it should be as comfortable as you like then - a VBar Control would be the solution ;-)



Quote:I am getting a little tail wag and I have the tail gyro gain down to 73. I haven't tried any further. Do you remember where you are running yours.

Increase it please ... it can handle much more - but depends on servo, blades, headspeed etc.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
rwilabee 13 August 2015 14:4413.08.2015 14:44
Quote: If it should be as comfortable as you like then - a VBar Control would be the solution ;-)

Rainer as fine a radio as the Vbar Control is I just can't justify getting it for one heli. My other 5 heli's are not flybarless and I also have 15 airplanes so my Futaba 14SG works well for most aircraft.

If I go ahead and put the SG on my Acrobatic would I be better going back to my Silverline or go forward with the Neo and my 14SG.

Thanks Again for all the Help.

Rich
rwilabee 14 August 2015 00:4514.08.2015 00:45
Rainer:

Checked in to see if you answered my last post and somehow I created this one by mistake. I can't figure out how to get rid of it.

Thanks

Rich



2 mal bearbeitet. Zuletzt am 14.08.2015 04:36 von rwilabee.
RV 14 August 2015 09:1414.08.2015 09:14
Unfortunately i can't follow your further questions - i don't have a T14 to check.

Using a 3rd Party TX for a nitro or gasser w/o our gov AND the throttle function from TX - just assign the TX throttle channel to AUX3 and set up according to TX/heli manual. As we are only passing the signal from RX to AUX3 in this case - we are out here. Just a task between TX, RX, (NEO passes) and throttle servo. You can also use the throttle channel on the SBus RX if it is there w/o the NEO - just plug the servo into RX.

But - please deliver us a channel with the states for your motor switch on our "Throttle" channel.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
rwilabee 14 August 2015 14:4214.08.2015 14:42
I am flying the Neo with out the gov and throttle function and all that works fine. Are those suggestions on the last post for using or not using the Gov and Throttle Function in the Neo with my Stator Gator.



1 mal bearbeitet. Zuletzt am 14.08.2015 15:01 von rwilabee.
RV 14 August 2015 19:2514.08.2015 19:25
Quote:Are those suggestions on the last post for using or not using the Gov and Throttle Function in the Neo with my Stator Gator.

OK - maybe it was not clear -maybe not. But as the post above talks about external TX and throttle ans AUX3 - it can ONLY be for non-VGov usage. Using VGov we would have been talking about the ESC port, and not about throttle curve in your non-VBC-tx etc. ...

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
rwilabee 14 August 2015 19:3714.08.2015 19:37
I understand that the Neo has a faster processor than my old Silverline. Looking forward to lots of good flying with it.

Thanks Again

Rich



1 mal bearbeitet. Zuletzt am 15.08.2015 05:17 von rwilabee.
rwilabee 16 August 2015 03:3716.08.2015 03:37
Rainer: Have you heard of this happening with your or any Acrobatic. I was checking with East Coast Vario here in the states regarding the correct gear ratio for a governor. He sent me this reply and said he checked with Vario Germany and even the new 5mm blade bolts will do it also.

Problem with benzins is that the gas motor will overspeed on this model with a govenor when you try and come down by unloading pitch. If you overspeed the head, you will elongate the bolt holes in the grips, and bend the blade bolts. That takes about 1.5 minutes to happen. Germany agrees with this and it includes the newer 5mm bolts.

Now I'm nervous about converting from my Throttle curves to my Stator Gator. I do want to be able to do loops and rolls on my Acrobatic.

Thanks

Rich
RV 16 August 2015 09:4716.08.2015 09:47
Quote:Problem with benzins is that the gas motor will overspeed on this model with a govenor when you try and come down by unloading pitch. If you overspeed the head, you will elongate the bolt holes in the grips, and bend the blade bolts. That takes about 1.5 minutes to happen. Germany agrees with this and it includes the newer 5mm bolts.

Well - if it overspeeds the MOTOR too much - the gov isn't se tup right. Especially the min throttle value was too high then. If it overspeeds the ROTOR - we can't do anything (freewheel) - just a thing of the pilots flying style!


A short story about my gasser:

On the vario day here in germany - we had a invitation of Kirsten Zodtner (Vario CEO) to show our VBar Control and NEO stuff. Of course i had the Gasser there too - and many customers asked to fly it. So we got permission from Kirsten to do - and Uli flew it (my skills aren't that good) - He flew loopings, rolls, rolling circles, flips, some piroflips - and everything is and went well. Even on the blades and their bolts. Well - why ... simple: On this flying style - the motor has no time to overspeed ... the pilot has to take care not to overload the system and drop down the headspeed too much ;-)

Anyway - i'll measure my bolts later. As i did some Autos on this heli too where i like to have some headspeed for the landing of course.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
rwilabee 17 August 2015 01:5317.08.2015 01:53
Oh wow interesting story, that must have been cool to actually get to interact with the Vario CEO and the Vario reps. I'm thinking about just setting up the Governor anyway, especially if Uli could fly the maneuvers that he did with no problem. I can only do loops, rolls, and some autos anyway, no 3D for me. I would like to mess with the Governor setup on the Neo as I think that is such a great feature. I did have to drill out the bolt holes on my Vario Blades to 5mm to accomodate the larger bolts they use on the flybarless blade holders when I did the conversion to flybarless. I think they use to use 2.5mm and I could see it happening on those.

Thanks for all the great info.

Rich
VStabi VStabi Pioneer of Flybarless