← VBar NEO for external transmitters

Vbar NEO Yaw rate too slow and External ESC help needed translated

VBar › VBar NEO for external transmitters · Started by Mike Wilson on 17 August 2015 18:0517.08.2015 18:05
Mike Wilson 17 August 2015 18:0517.08.2015 18:05
I just setup a new Vbar NEO with 6.1 Pro w/o rescue and I am finding the Yaw rate a bit too slow. With the Vbar silverline and 5.3 that I replaced, I had the Yaw set to 115 and it was fast enough. With the NEO I have it set to 120 and it is still a tad bit too slow. I am using the non vcontrol version and PC software to setup the NEO. I have seen reference to a yaw overdrive option that is available in the vcontrol to achieve faster yaw rates but I do not see this option in the PC software. Is there a way to enable this option with the PC software?

I also have a second issue with my throttle curves. I am Kosmik 200 ESC so I am not using the Vbar Gov. I have set my throttle output for each bank in the PC software and the ESC gov is working just fine. The issue that I have is trying to get the ESC auto bailout function to work. When I hit hold on my TX, the throttle signal goes to zero in the Vbar instead of what the throttle curve in the radio is set for. Is there a way to get this function to work properly in the Vbar or is my only option to remap the throttle channel to an Aux channel? Also, if I remap the throttle channel will my failsafe still function properly?

....Mike
RV 17 August 2015 18:1317.08.2015 18:13
Quote:Is there a way to enable this option with the PC software?

Not at this moment - VBC only. But if someone has a VBC ...



Quote:When I hit hold on my TX, the throttle signal goes to zero in the Vbar instead of what the throttle curve in the radio is set for.

What kind of status is displayed in the PC Software? Off, Run or Idle? (must be Idle - center of the "motor" channel)

If Idle is displayed AND the motor was in "run" before - we will give the Idle value to the ESC.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Mike Wilson 17 August 2015 19:0717.08.2015 19:07
Thanks for the quick reply.

I was getting a motor Stop value with my Hold in the TX set to 25%. I increased the hold to about 36% and I now get the motor Idle value in the Vbar PC software. I can now set the Idle value in the PC software. It looks like this will solve my issue. I will test and let you know.

As for using someone elses vcontrol to set my Yaw overdrive, do I need to add a vcontrol rx to my NEO in order to use a vcontrol radio to configure my non vcontrol NEO?
RV 17 August 2015 19:1017.08.2015 19:10
Ok - idle should be solved ;-) - Anyway i would not set the value "on the edge" to off - i would use center (50%).


Quote:do I need to add a vcontrol rx to my NEO in order to use a vcontrol radio to configure my non vcontrol NEO

Yep - see our NEO FAQ how to connect. The VBC will be the master then (if both systems plugged in) and you can also do crossover buddyboxing ...

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Mike Wilson 17 August 2015 19:2917.08.2015 19:29
Yes, I tested the throttle hold and it works fine and I have also set the hold position in the radio to 50%.


If I use a vcontrol radio to set the yaw overdrive feature, will that value be reset if I then connect the PC software or will it always remain until I either reset the configuration of change it with the vcontrol again?

Thanks again for your assistance.
RV 17 August 2015 19:5317.08.2015 19:53
Quote:If I use a vcontrol radio to set the yaw overdrive feature, will that value be reset if I then connect the PC software or will it always remain until I either reset the configuration of change it with the vcontrol again?

It will keep the value - except you touch the slider or type in another one.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Mike Wilson 17 August 2015 20:2317.08.2015 20:23
Why is the yaw overdrive not available in the PC software? There are others that are having this issue with slow yaw rate as well. Is there any plan on including it in the future?
RV 17 August 2015 22:3717.08.2015 22:37
The NEO and V6.1 is a bit different here, so it is as it is.

If you want to get the NEO/V6 with a 3rd party radio - this is part of the deal, 3rd party radios will always have some differencies to VBar Control in case of internal limitations.

If you have a VBar Control - you have full access to all values.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
VStabi VStabi Pioneer of Flybarless