joecass
28 September 2016 02:1428.09.2016 02:14
I just switched from silver line vbar to neo. The problem I'm having is the head speed is lower then the desired head speed in the Software. Also when switching from bank 2 (1800) to bank 3 (1900) there is no increase of RPM.
I read the info on vbar website about setting up on gasser but still can't figure it out. I have my throttle linkage set up as per the link to runryder.
I'm using futaba 14SG radio.
I have a lot of Governor is at Low Throttle Limit in the log
Eddi E. aus G.
28 September 2016 08:4028.09.2016 08:40
Hi,
is everything dialled in properly, pole count (for the sensor), gear ratio, max. head speed?
Does the carb open further (or can it open further) when you go to 1,900 1/min?
Do you also get Governor at full throttle entries?
The low throttle limit entries mean that the desired head speed is lower than what the governor can set (means, even if the engine is idling or limited at the minimum throttle limit, the head speed is higher than desired).
Kind regards
Eddi
Born to fly ...
forced to work.
joecass
28 September 2016 10:1128.09.2016 10:11
pole count is set to 1. Im using a futaba sensor. I don't see a place to enter max head speed in the software. The carb can opening more if needed at 1900. I do not get governor at full throttle entries.
joecass
28 September 2016 10:1928.09.2016 10:19
joecass schrieb:
-------------------------------------------------------
> pole count is good. gear ratio is good.
> I don't see a place to enter max head speed in the
> software. The carb can opening more if needed at
> 1900. I do not get governor at full throttle
> entries.
Eddi E. aus G.
28 September 2016 11:0528.09.2016 11:05
Hi,
oh, OK, I just noticed that the max. head speed parameter is no longer present in 6.x ... sorry for the confusion.
I'm a little bit out out my depth here anyway, can't tell if adjusting the engine further could help, like making it run leaner or richer, so it revs more.
Kind regards
Eddi
Born to fly ...
forced to work.
joecass
28 September 2016 11:2428.09.2016 11:24
I had it on the silver line vbar gov and it work really good so it's not a tunning problem.
Eddi E. aus G.
28 September 2016 11:3828.09.2016 11:38
OK, no changes here ...
Can you still compare the parameters, maybe you did some changes or tweaks on the silverline which are missing on the NEO now?
Born to fly ...
forced to work.
joecass
28 September 2016 13:1128.09.2016 13:11
Couldn't find anything different between the two.
Eddi E. aus G.
28 September 2016 15:3128.09.2016 15:31
OK, maybe Rainer has some ideas: he's the nitro governor guru and has a gasser himself.
Born to fly ...
forced to work.
RV
28 September 2016 17:4528.09.2016 17:45
If you have low throttle warnings - the min limit is too high for this HS. Please select as low as needed to get it gov'ed - but as high as possible to avoid motor shutdown in a descent.
Anyway - simple question ... where is the throttle servo plugged in?
Do you get a RPM display on the VBar Control form the sensor? (using 3rd party radios - see in PC soft while motor running)
Can you share the setup file here?
Also the complete logs?
(zip and attach)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
joecass
28 September 2016 22:3028.09.2016 22:30
Throttle servo is plugged into the esc port.
I get a rpm display in the pc software at idle it was showing about 1300.
I can't load the files I don't know why.
What I noticed is that in the pc software the green led is always lit for low limit no mater what I do I can't get it to ever go out.
I brought the min limit all the way down to 5 still the same thing also green led is still lit. The throttle servo will move to full throttle with bank one set. The low limit led is still lit. I also can switch the gov. on with bank 2 or 3 and the throttle servo moves slowly up to full throttle position and the purple throttle position moves all the way up but low limit is still on.
RV
29 September 2016 10:0029.09.2016 10:00
To add files - zip them and attach.
How is your motor switch handling? Is it according to the manual? 2 seperate switches, one of them as 3-way?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
joecass
29 September 2016 14:3729.09.2016 14:37
I zipped the files but still will not send. I keep getting a message saying it dose not support this file type. I'm going to try on a another computer after work .
I have one single switch that is engine cut. I also have a 3 position switch for all banks and a nother 3 position switch that is run/idle/ motor stop. All switches seem to be operating normal.
If I move from run to idle I have a kind of high idle the clutch is engage and blades are spinning. If I switch from idle to motor stop I have normal idle clutches is disengaged and the blades are no longer powered. On the other switch all banks are switching. Thanks for the help so far.
RV
29 September 2016 19:5029.09.2016 19:50
OK - maybe the file ending was not ".zip" ?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
joecass
30 September 2016 00:3930.09.2016 00:39
here is the file
Dateianhänge:
öffnen |
Download -
neo setup file.zip
(471 bytes)
joecass
30 September 2016 00:4030.09.2016 00:40
here is the log
Dateianhänge:
öffnen |
Download -
log-20006432-Sep-27--2016-7-46-54-PM.log vbar neo (2).zip
(1.8 KB)
RV
2 October 2016 10:2502.10.2016 10:25
OK - everything seems well here - except the low limit warnings in the log.
They are definitely the hint - your throttle is still beneath this point in your regarding files durcing the flight.
So - it might have to do with the throttle setup in general - it is 120/127 at the throw. I would like to see if it changes anything getting closer to 100/100 - can you try a longer throttle servo horn?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
joecass
3 October 2016 02:4703.10.2016 02:47
I just got done setting up throttle servo arm I'm at 105 now on both sides. I'm going to try it tomorrow.
I figured out the low throttle limit logs. I thought this would fix it but it is still doing the same thing. I turned off the fail safe on channel 3 in the TX. Now only the ramp up green LED is light on the front page of the PC software also there are no more low limit logs.
here is the log from today
Dateianhänge:
öffnen |
Download -
log file neo.zip
(663 bytes)
RV
3 October 2016 10:5303.10.2016 10:53
Was it ok in flight now or not?
Also - try to estimate the basic throttle and collective ad values in Bank1 (normal mode bank) like here to give me a hint:
http://vstabi.info/en/node/2030
Second diagram.
How much basic is needed for your headspeed on the ground at zero collective?
How much collective ad is in addition then needed to keep the HS (just hear) at a medum climb?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
joecass
3 October 2016 23:0503.10.2016 23:05
Still not working. Also the low limit logs are back again. When I switch the gov on it starts reving the engine up and down making the tail kick. Also the head speed is low.
I got Basic at 20 and collective add is at 60 I did not have anything to measure the head speed but it sounded to me like just under 1800.
RV
4 October 2016 18:4404.10.2016 18:44
I got Basic at 20
So - you need min limit LOWER than this.
But - this is close to zero ;-( - be careful.
I would try 10 as min limit.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
joecass
4 October 2016 23:3304.10.2016 23:33
No good I tried min throttle at 10 and and 3 same thing I checked the long even running it at 3 I still get the min throttle logs. I also noticed that I get gov mode pitch every time I switch gov on then low throttle limit.
Here is a video of it when turing on the gov.
https://youtu.be/VpvqD9qcCkE
joecass
5 October 2016 00:0905.10.2016 00:09
So I tried running the low throttle limit at 40 and I also put the gain from 50 to 20 the gov is working now I still have low throttle limits stored in the log. Also when doing Aeleron tic toc the motor started to bog down. The gov needs to open the throttle more what do I need to adjust for this? Also should I try raising up the low limit more to see if I can get them out of the log? Should i put the gain back to 50?
RV
5 October 2016 17:4205.10.2016 17:42
Well - there is a tweaking order here at the end of this article:
http://www.vstabi.info/en/node/2030
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
joecass
8 October 2016 00:5608.10.2016 00:56
I'm still losing head speed when doing tic toc