← VBar NEO for external transmitters

NEO not working after 6.4 update

VBar › VBar NEO for external transmitters · Started by swalko on 23 December 2020 10:2623.12.2020 10:26
RV 30 December 2020 14:2530.12.2020 14:25
Power on Servo ... the servo output is not switched. Only the Pulse output to the servos is given as soon as time allows. Probably all 3 together simultaneous (which is the best of course).

As this is the only case we her about this right now - i am afraid we need exactly your equipment to narrow it down if the NEO is okay in our shop at the test bench.

Anyway - lets check the NEO first, please file a service report if not done yet.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
swalko 31 December 2020 10:4531.12.2020 10:45
OK, i understand, but we both know about what i am talking.
I think that after years we found a reason why some Kosmiks "worked" without backup battery and some needed it.
Kosmik will switch BEC to full power only when receive correct throttle signal. But it need to get correct signal as fast as possible, otherwise there is a chance that there will not be enough power for other equipment to work correctly.
One RX boot faster, one slower, use routing from VBar will add another delay. Here i talk about hundredth of second.
Based on my tests, i connected everything as before 6.4 update with one change. I directly connected throttle signal pin from my RX to Kosmik with single wire. Everything works great.



1 mal bearbeitet. Zuletzt am 31.12.2020 11:11 von swalko.
RV 31 December 2020 11:5631.12.2020 11:56
Okay. Thnaks for the Info.

As soon as time allows and I#ll be in touch with Kontronik i'll address this to get a bit more time unless the esc goes mad here.

The AUX3 solution is only used on the 3rd party radio guys who do not follow our recommendation to use the original AUX function and oner percentage in NEO each bank as we do with VBC - so there may be a delay included too ;-(

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.




1 mal bearbeitet. Zuletzt am 31.12.2020 11:59 von RV.
swalko 31 December 2020 13:4331.12.2020 13:43
It will be best if Kosmik will not wait for correct signal, but it will switch BEC to full power as fast as possible. But it can be hardwired in Kosmik, so i will wait what you come up with.

I understand, my setup is complicated, with few rpms modes combined with different banks and ability to adjust rpms on the fly, retracts, ... And that is a reason why i use AUX3 to route throttle channel.

In a principle, it is not a problem for me to use it as it works now with 6.4 . I am glad i found and solved it so i can use my TDR2 again.

Rainer, can i connect my retracts to AUX3 port on NEO?
RV 1 January 2021 07:4301.01.2021 07:43
You can use AUX3 now for other stuff of course - you can also use AUX2 (if not for Gyro gain used).

The difference is - AUX3 has a built in failsafe after 0.5s for "motor off" when there are no ingoing signals from the RX. AUX2 does not have this, it just holds.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
swalko 1 January 2021 10:5701.01.2021 10:57
Thank you Rainer!

Milan
VStabi VStabi Pioneer of Flybarless