swalko
23 December 2020 10:2623.12.2020 10:26
Today i done update from 6.3 to 6.4 firmware on my NEO and now it is not working.
It is possible to switch it to firmware update mode (with plug connected) , so VBar Control manager see it and i can switch between firmwares without issues.
But when i try to boot it without plug connected it will not boot, still resets self in loop and cause my RX to reset too (SBUS connection) . I tried another RX and it is still same, both RXs works without issues without VBar connected.
If i connect NEO to computer with running software i see that sw try to connect to unit, but after while it resets and continue in loop.
Before 6.4 update everything worked without issues.
https://www.youtube.com/watch?v=PL03vOu-oxk
1 mal bearbeitet. Zuletzt am 23.12.2020 12:04 von swalko.
RV
23 December 2020 14:5023.12.2020 14:50
Cloud you load a Express and check?
if ok then - Reload the Pro?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
swalko
23 December 2020 15:2023.12.2020 15:20
Hi Rainer
I already tried 6.4 Express, 6.4 Professional, 6.1 testing and then i loaded 6.4 Professional Rescue. It is still same. Before flashing led flash blue, after flashing unit flash green. I see that mass storage device partition was mounted. Last few times Windows detected corruption on mounted partition and i let it repair with successful result. I tried to flash firmware on three different machines, one MacOS, 2x Windows 10 machines with same result :-( .
RV
23 December 2020 18:5723.12.2020 18:57
Which SN is it?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
swalko
23 December 2020 19:1023.12.2020 19:10
RV
24 December 2020 14:0324.12.2020 14:03
Okay - there is nothing wrong on our side. Is this a NEO with sat on board or external one? - If external one, disconnect during the update for a try.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
swalko
24 December 2020 14:0924.12.2020 14:09
Without int/ext sats. I use S-BUS.
RV
24 December 2020 14:4724.12.2020 14:47
Hmmm ... so at this point i am afraid i can't solve it online, it seems to be a hardware issue.
Please file a rma by clicking on this device "service request" icon in your list here. Eddi will take over then, but keep note we have holidays until 4th of January here. I hope you have something else to fly these days ,-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
swalko
24 December 2020 15:0124.12.2020 15:01
Until 6.4 update everything worked. As first i connected NEO with SW and checked configuration. I dont have spare unit or helicopter, but it is not a problem. Bigger problem is that i need NEO configuration for every bank, because i dont have latest fonfigurations in my computers, so i hope it will stay preserved. I will try to disconnect everything and flash it again. Is there a way to completely rollout back to 6.3 version?
swalko
24 December 2020 18:0324.12.2020 18:03
Hi Rainer
So i done few tests. I am able to boot my NEO without connected receiver. It starts in Failsafe mode due to missing RX input. Then i am able connect to unit with PC sw. Servos are not armed, but everything seems ok. I am able to boot NEO with connected receiver and turned off radio. When i turn on radio and RX binds with TX, NEO starts that infinite loop of restarts and RX restarts too. If i switch off radio, RX fall in failsafe mode and NEO boot again without issues.
Is not there some incompatibility with Frsky S-BUS receivers and 6.4 firmware? I updated my Frsky receivers to new 2.1 firmware, but after this update NEO 6.3 worked without issues.
Problems is same with both my receivers, but both are same RX with same firmware.
Here is log from my testing session:
Thu Dec 24 17:20:59 CET 2020
Serial: 2000****
Firmware: 6.4
Patchlevel: 48
---- start ----
Info 0:01 Bank 2 Loaded
Info 0:01 Motor Switch operated to OFF
Info 0:01 Motor Switch operated to Idle bailout
Info 0:02 Bank 2 Loaded
Info 0:02 Motor Switch operated to OFF
Info 0:02 Motor Switch operated to Idle bailout
Info 0:03 Bank 2 Loaded
Info 0:03 Motor Switch operated to OFF
Info 0:03 Motor Switch operated to Idle bailout
Info 0:04 Bank 2 Loaded
Info 0:04 Motor Switch operated to Idle bailout
Info 0:05 Motor Switch operated to OFF
Info 0:06 Bank 2 Loaded
Info 0:06 Motor Switch operated to OFF
Info 0:06 Motor Switch operated to Idle bailout
Info 0:07 Bank 2 Loaded
Info 0:07 Motor Switch operated to OFF
Info 0:07 Motor Switch operated to Idle bailout
OK 0:00 Reset Reason: Power On
Info 0:00 Bank 2 Loaded
Info 0:00 Motor Switch operated to OFF
Info 0:00 Motor Switch operated to Idle bailout
Info 0:01 Bank 2 Loaded
Info 0:01 Motor Switch operated to OFF
Info 0:01 Motor Switch operated to Idle bailout
Info 0:02 Bank 2 Loaded
Info 0:02 Motor Switch operated to Idle bailout
Info 0:03 Motor Switch operated to OFF
Info 0:04 Bank 2 Loaded
Info 0:04 Motor Switch operated to OFF
Info 0:04 Motor Switch operated to Idle bailout
Info 0:05 Bank 2 Loaded
Info 0:05 Motor Switch operated to OFF
Info 0:05 Motor Switch operated to Idle bailout
Info 0:06 Bank 2 Loaded
Info 0:06 Motor Switch operated to OFF
Info 0:06 Motor Switch operated to Idle bailout
Info 0:07 Bank 2 Loaded
Info 0:07 Motor Switch operated to OFF
Info 0:07 Motor Switch operated to Idle bailout
Info 0:08 Bank 2 Loaded
Info 0:08 Motor Switch operated to OFF
Info 0:08 Motor Switch operated to Idle bailout
Info 0:09 Bank 2 Loaded
Info 0:09 Motor Switch operated to OFF
Info 0:09 Motor Switch operated to Idle bailout
Info 0:10 Bank 2 Loaded
Info 0:10 Motor Switch operated to OFF
Info 0:10 Motor Switch operated to Idle bailout
Info 0:11 Bank 2 Loaded
Info 0:11 Motor Switch operated to OFF
Info 0:11 Motor Switch operated to Idle bailout
Info 0:12 Bank 2 Loaded
Info 0:12 Motor Switch operated to OFF
Info 0:12 Motor Switch operated to Idle bailout
Info 0:13 Bank 2 Loaded
Info 0:13 Motor Switch operated to OFF
Info 0:13 Motor Switch operated to Idle bailout
Info 0:14 Bank 2 Loaded
Info 0:14 Motor Switch operated to Idle bailout
Info 0:15 Motor Switch operated to OFF
Info 0:16 Bank 2 Loaded
Info 0:16 Motor Switch operated to OFF
Info 0:16 Motor Switch operated to Idle bailout
Info 0:17 Bank 2 Loaded
Info 0:17 Motor Switch operated to OFF
Info 0:17 Motor Switch operated to Idle bailout
Info 0:18 Bank 2 Loaded
Info 0:18 Motor Switch operated to OFF
Info 0:18 Motor Switch operated to Idle bailout
Info 0:19 Bank 2 Loaded
Info 0:19 Motor Switch operated to OFF
Info 0:19 Motor Switch operated to Idle bailout
OK 0:00 Reset Reason: Power On
Info 0:00 Bank 2 Loaded
Info 0:00 Motor Switch operated to OFF
Info 0:00 Motor Switch operated to Idle bailout
Info 0:01 Bank 2 Loaded
Info 0:01 Motor Switch operated to OFF
Info 0:01 Motor Switch operated to Idle bailout
Info 0:02 Bank 2 Loaded
Info 0:02 Motor Switch operated to OFF
Info 0:02 Motor Switch operated to Idle bailout
Info 0:03 Bank 2 Loaded
Info 0:03 Motor Switch operated to OFF
Info 0:03 Motor Switch operated to Idle bailout
Info 0:04 Bank 2 Loaded
Info 0:04 Motor Switch operated to OFF
Info 0:04 Motor Switch operated to Idle bailout
Info 0:05 Bank 2 Loaded
Info 0:05 Motor Switch operated to OFF
Info 0:05 Motor Switch operated to Idle bailout
Info 0:06 Bank 2 Loaded
Info 0:06 Motor Switch operated to Idle bailout
Info 0:07 Motor Switch operated to OFF
Info 0:08 Bank 2 Loaded
Info 0:08 Motor Switch operated to OFF
Info 0:08 Motor Switch operated to Idle bailout
Info 0:09 Bank 2 Loaded
Info 0:09 Motor Switch operated to OFF
Info 0:09 Motor Switch operated to Idle bailout
Info 0:10 Bank 2 Loaded
Info 0:10 Motor Switch operated to OFF
Info 0:10 Motor Switch operated to Idle bailout
Info 0:11 Bank 2 Loaded
Info 0:11 Motor Switch operated to OFF
Info 0:11 Motor Switch operated to Idle bailout
Info 0:12 Bank 2 Loaded
Info 0:12 Motor Switch operated to OFF
Info 0:12 Motor Switch operated to Idle bailout
Info 0:13 Bank 2 Loaded
Info 0:13 Motor Switch operated to OFF
Info 0:13 Motor Switch operated to Idle bailout
Info 0:14 Bank 2 Loaded
Info 0:14 Motor Switch operated to OFF
Info 0:14 Motor Switch operated to Idle bailout
Info 0:15 Bank 2 Loaded
Info 0:15 Motor Switch operated to OFF
Info 0:15 Motor Switch operated to Idle bailout
OK 0:00 Reset Reason: Power On
Info 0:00 Bank 2 Loaded
Info 0:00 Motor Switch operated to Idle bailout
OK 0:10 Good Health Message (10sec)
OK 0:20 Good Health Message (10sec)
OK 0:00 Reset Reason: Power On
Info 0:00 Bank 2 Loaded
Info 0:00 Motor Switch operated to Idle bailout
OK 0:10 Good Health Message (10sec)
OK 0:20 Good Health Message (10sec)
OK 0:30 Good Health Message (10sec)
OK 0:40 Good Health Message (10sec)
OK 0:50 Good Health Message (10sec)
OK 1:00 Good Health Message (10sec)
OK 1:10 Good Health Message (10sec)
OK 1:20 Good Health Message (10sec)
OK 1:30 Good Health Message (10sec)
OK 1:40 Good Health Message (10sec)
OK 1:50 Good Health Message (10sec)
OK 2:00 Good Health Message (10sec)
OK 2:10 Good Health Message (10sec)
OK 2:20 Good Health Message (10sec)
OK 2:30 Good Health Message (10sec)
OK 2:40 Good Health Message (10sec)
OK 2:50 Good Health Message (10sec)
OK 3:00 Good Health Message (10sec)
OK 3:10 Good Health Message (10sec)
OK 3:20 Good Health Message (10sec)
OK 3:30 Good Health Message (10sec)
OK 3:40 Good Health Message (10sec)
OK 3:50 Good Health Message (10sec)
OK 0:00 Reset Reason: Power On
Info 0:00 Bank 2 Loaded
Info 0:00 Motor Switch operated to Idle bailout
Warn 0:02 Init Failed, retrying...
OK 0:12 Good Health Message (10sec)
OK 0:22 Good Health Message (10sec)
OK 0:32 Good Health Message (10sec)
OK 0:42 Good Health Message (10sec)
OK 0:52 Good Health Message (10sec)
OK 1:02 Good Health Message (10sec)
OK 1:12 Good Health Message (10sec)
OK 1:22 Good Health Message (10sec)
OK 1:32 Good Health Message (10sec)
OK 1:42 Good Health Message (10sec)
OK 1:52 Good Health Message (10sec)
OK 2:02 Good Health Message (10sec)
OK 2:12 Good Health Message (10sec)
OK 2:22 Good Health Message (10sec)
OK 2:32 Good Health Message (10sec)
OK 2:42 Good Health Message (10sec)
OK 2:52 Good Health Message (10sec)
OK 3:02 Good Health Message (10sec)
OK 3:12 Good Health Message (10sec)
OK 3:22 Good Health Message (10sec)
OK 3:32 Good Health Message (10sec)
OK 3:42 Good Health Message (10sec)
OK 3:52 Good Health Message (10sec)
OK 4:02 Good Health Message (10sec)
OK 4:12 Good Health Message (10sec)
OK 4:22 Good Health Message (10sec)
OK 0:00 Reset Reason: Power On
Info 0:00 Bank 2 Loaded
Info 0:00 Motor Switch operated to Idle bailout
OK 0:10 Good Health Message (10sec)
OK 0:20 Good Health Message (10sec)
OK 0:30 Good Health Message (10sec)
OK 0:40 Good Health Message (10sec)
OK 0:50 Good Health Message (10sec)
OK 1:00 Good Health Message (10sec)
OK 1:10 Good Health Message (10sec)
OK 1:20 Good Health Message (10sec)
OK 1:30 Good Health Message (10sec)
OK 1:40 Good Health Message (10sec)
OK 1:50 Good Health Message (10sec)
OK 2:00 Good Health Message (10sec)
OK 2:10 Good Health Message (10sec)
OK 2:20 Good Health Message (10sec)
OK 2:30 Good Health Message (10sec)
OK 2:40 Good Health Message (10sec)
OK 2:50 Good Health Message (10sec)
OK 3:00 Good Health Message (10sec)
OK 3:10 Good Health Message (10sec)
OK 3:20 Good Health Message (10sec)
OK 3:30 Good Health Message (10sec)
OK 3:40 Good Health Message (10sec)
OK 3:50 Good Health Message (10sec)
OK 4:00 Good Health Message (10sec)
OK 4:10 Good Health Message (10sec)
OK 4:20 Good Health Message (10sec)
OK 4:30 Good Health Message (10sec)
OK 4:40 Good Health Message (10sec)
OK 4:50 Good Health Message (10sec)
OK 5:00 Good Health Message (10sec)
OK 5:10 Good Health Message (10sec)
OK 5:20 Good Health Message (10sec)
OK 5:30 Good Health Message (10sec)
OK 5:40 Good Health Message (10sec)
OK 5:50 Good Health Message (10sec)
OK 6:00 Good Health Message (10sec)
OK 6:10 Good Health Message (10sec)
OK 6:20 Good Health Message (10sec)
OK 6:30 Good Health Message (10sec)
OK 6:40 Good Health Message (10sec)
OK 6:50 Good Health Message (10sec)
OK 7:00 Good Health Message (10sec)
OK 7:10 Good Health Message (10sec)
Info 7:20 Motor Switch operated to OFF
Critical 0:00 Warmstart
Info 0:00 Bank 2 Loaded
Info 0:00 Motor Switch operated to OFF
Info 0:00 Motor Switch operated to Idle bailout
Warn 0:01 RC Input Packet lost
Critical 0:00 Warmstart
Info 0:00 Bank 2 Loaded
Info 0:00 Motor Switch operated to OFF
Info 0:00 Motor Switch operated to Idle bailout
Critical 0:00 Warmstart
Info 0:00 Bank 2 Loaded
Info 0:00 Motor Switch operated to OFF
Info 0:00 Motor Switch operated to Idle bailout
Critical 0:00 Warmstart
Info 0:00 Bank 2 Loaded
Info 0:00 Motor Switch operated to OFF
Info 0:00 Motor Switch operated to Idle bailout
Critical 0:00 Warmstart
Info 0:00 Bank 2 Loaded
Info 0:00 Motor Switch operated to OFF
Info 0:00 Motor Switch operated to Idle bailout
Critical 0:00 Warmstart
Info 0:00 Bank 2 Loaded
Info 0:00 Motor Switch operated to OFF
Info 0:00 Motor Switch operated to Idle bailout
Critical 0:00 Warmstart
Info 0:00 Bank 2 Loaded
Info 0:00 Motor Switch operated to OFF
Info 0:00 Motor Switch operated to Idle bailout
Critical 0:00 Warmstart
Info 0:00 Bank 2 Loaded
Info 0:00 Motor Switch operated to OFF
Info 0:00 Motor Switch operated to Idle bailout
Critical 0:00 Warmstart
Info 0:00 Bank 2 Loaded
Info 0:00 Motor Switch operated to OFF
Info 0:00 Motor Switch operated to Idle bailout
Critical 0:00 Warmstart
Info 0:00 Bank 2 Loaded
Info 0:00 Motor Switch operated to OFF
Info 0:00 Motor Switch operated to Idle bailout
Critical 0:00 Warmstart
Info 0:00 Bank 2 Loaded
Info 0:00 Motor Switch operated to OFF
Info 0:00 Motor Switch operated to Idle bailout
Critical 0:00 Warmstart
Info 0:00 Bank 2 Loaded
Info 0:00 Motor Switch operated to OFF
Info 0:00 Motor Switch operated to Idle bailout
Critical 0:00 Warmstart
Info 0:00 Bank 2 Loaded
Info 0:00 Motor Switch operated to OFF
Info 0:00 Motor Switch operated to Idle bailout
Critical 0:00 Warmstart
Info 0:00 Bank 2 Loaded
Info 0:00 Motor Switch operated to OFF
Info 0:00 Motor Switch operated to Idle bailout
Critical 0:00 Warmstart
Info 0:00 Bank 2 Loaded
Info 0:00 Motor Switch operated to OFF
Info 0:00 Motor Switch operated to Idle bailout
Critical 0:00 Warmstart
Info 0:00 Bank 2 Loaded
Info 0:00 Motor Switch operated to Idle bailout
Info 0:01 Motor Switch operated to OFF
Critical 0:00 Warmstart
Info 0:00 Bank 2 Loaded
Info 0:00 Motor Switch operated to OFF
Info 0:00 Motor Switch operated to Idle bailout
Critical 0:00 Warmstart
Info 0:00 Bank 2 Loaded
Info 0:00 Motor Switch operated to OFF
Info 0:00 Motor Switch operated to Idle bailout
Warn 0:01 RC Input Packet lost
Critical 0:01 RC Failsafe has been activated
OK 0:11 Good Health Message (10sec)
OK 0:21 Good Health Message (10sec)
OK 0:31 Good Health Message (10sec)
OK 0:41 Good Health Message (10sec)
OK 0:51 Good Health Message (10sec)
OK 1:01 Good Health Message (10sec)
OK 1:11 Good Health Message (10sec)
OK 1:21 Good Health Message (10sec)
OK 1:31 Good Health Message (10sec)
OK 1:41 Good Health Message (10sec)
OK 1:51 Good Health Message (10sec)
OK 2:01 Good Health Message (10sec)
OK 2:11 Good Health Message (10sec)
OK 2:21 Good Health Message (10sec)
OK 2:31 Good Health Message (10sec)
OK 2:41 Good Health Message (10sec)
OK 2:51 Good Health Message (10sec)
OK 3:01 Good Health Message (10sec)
OK 3:11 Good Health Message (10sec)
OK 3:21 Good Health Message (10sec)
OK 3:31 Good Health Message (10sec)
OK 3:41 Good Health Message (10sec)
OK 3:51 Good Health Message (10sec)
OK 4:01 Good Health Message (10sec)
OK 4:11 Good Health Message (10sec)
OK 4:21 Good Health Message (10sec)
OK 0:00 Reset Reason: Power On
Info 0:00 Bank 2 Loaded
Info 0:00 Motor Switch operated to Idle bailout
OK 0:10 Good Health Message (10sec)
OK 0:20 Good Health Message (10sec)
OK 0:30 Good Health Message (10sec)
OK 0:40 Good Health Message (10sec)
OK 0:50 Good Health Message (10sec)
OK 1:00 Good Health Message (10sec)
OK 1:10 Good Health Message (10sec)
OK 1:20 Good Health Message (10sec)
OK 1:30 Good Health Message (10sec)
OK 1:40 Good Health Message (10sec)
OK 1:50 Good Health Message (10sec)
OK 2:00 Good Health Message (10sec)
OK 2:10 Good Health Message (10sec)
Info 2:14 Bank 3 Loaded
Info 2:14 Motor Switch operated to OFF
Info 2:15 Calibration Finished
Critical 0:00 Warmstart
Info 0:00 Bank 2 Loaded
Info 0:00 Motor Switch operated to OFF
Info 0:00 Motor Switch operated to Idle bailout
Info 0:01 Bank 3 Loaded
Critical 0:00 Warmstart
Info 0:00 Bank 2 Loaded
Info 0:00 Motor Switch operated to OFF
Info 0:00 Motor Switch operated to Idle bailout
Info 0:01 Bank 3 Loaded
Critical 0:00 Warmstart
Info 0:00 Bank 2 Loaded
Info 0:00 Motor Switch operated to OFF
Info 0:00 Motor Switch operated to Idle bailout
Info 0:01 Bank 3 Loaded
Critical 0:00 Warmstart
Info 0:00 Bank 2 Loaded
Info 0:00 Motor Switch operated to OFF
Info 0:00 Motor Switch operated to Idle bailout
Info 0:01 Bank 3 Loaded
Critical 0:00 Warmstart
Info 0:00 Bank 2 Loaded
Info 0:00 Motor Switch operated to OFF
Info 0:00 Motor Switch operated to Idle bailout
Info 0:01 Bank 3 Loaded
Critical 0:00 Warmstart
Info 0:00 Bank 2 Loaded
Info 0:00 Bank 3 Loaded
Info 0:00 Motor Switch operated to OFF
Info 0:00 Motor Switch operated to Idle bailout
Critical 0:00 Warmstart
Info 0:00 Bank 2 Loaded
Info 0:00 Motor Switch operated to OFF
Info 0:00 Motor Switch operated to Idle bailout
Info 0:01 Bank 3 Loaded
Critical 0:00 Warmstart
Info 0:00 Bank 2 Loaded
Info 0:00 Bank 3 Loaded
Info 0:00 Motor Switch operated to OFF
Info 0:00 Motor Switch operated to Idle bailout
Critical 0:00 Warmstart
Info 0:00 Bank 2 Loaded
Info 0:00 Motor Switch operated to Idle bailout
Info 0:01 Bank 3 Loaded
Info 0:01 Motor Switch operated to OFF
Critical 0:00 Warmstart
Info 0:00 Bank 2 Loaded
Info 0:00 Motor Switch operated to OFF
Info 0:00 Motor Switch operated to Idle bailout
Info 0:01 Bank 3 Loaded
Critical 0:00 Warmstart
Info 0:00 Bank 2 Loaded
Info 0:00 Motor Switch operated to OFF
Info 0:00 Motor Switch operated to Idle bailout
Info 0:01 Bank 3 Loaded
Critical 0:00 Warmstart
Info 0:00 Bank 2 Loaded
Info 0:00 Motor Switch operated to Idle bailout
OK 0:10 Good Health Message (10sec)
---- end ----
RV
24 December 2020 18:3224.12.2020 18:32
Quote:Critical 0:00 Warmstart
This should not happen - please create a service request.
A rollback isn't possible - and it won't solve the issue, i think we have a hardware issue, so glad it came up now and not in flight.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
swalko
24 December 2020 19:0024.12.2020 19:00
Warmstarts happen when rx binds with tx. I will try to disconnect servos and if problem persists i will send my NEO for service.
But it is strange that this happend in a time of 6.4 update.
swalko
24 December 2020 19:1324.12.2020 19:13
How can i save settings for all banks? I cannot switch banks due to channel in failsafe mode and it stays still in Bank2.
swalko
24 December 2020 20:4324.12.2020 20:43
Definately it is NEO itself. I done another tests and found:
1.) Disconnected servos, NEO boot and everything seems fine
2.) Connected tail servo, NEO boot and everything seems fine
3.) Connected tail servo and one cyclic servo (independent what servo i use and independent in what servo output on NEO i connect servo), NEO boot and everything seems fine
4.) Connected/disconnected tail servo and two cyclic servos (independent what servo i use and independent what servo outputs on NEO i connect servos), NEO resets itself in loop
Luckily i was able to download configurations for all banks :-) .
RV
25 December 2020 13:0825.12.2020 13:08
Okay - BTW .. on a NEO the setup file contains all banks - so no separate file each bank required ;-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
swalko
25 December 2020 14:5725.12.2020 14:57
OK, thanks. I grew on VStabi V4 and V5 software, so i was not sure how it works on NEO :-) .
swalko
27 December 2020 18:3627.12.2020 18:36
And today i found ... if i boot NEO 6.4 with only one cyclic servo connected, when unit booted up, i can connect other cyclic servos too and everything works as expected.
Rainer, may you ask Uli if there was not introduced some feature in 6.4 that may cause this behaviour?
https://www.youtube.com/watch?v=HEDG8u634Do
RV
27 December 2020 20:1427.12.2020 20:14
i can't see anything wrong on this heli ... except ... probably ... in very rare cases the BEC of the ESC. Could you boot with a 2s LiPo instead the BEC and all servos?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
swalko
28 December 2020 11:0728.12.2020 11:07
Hi Rainer
I dont have 2s here, but if i connect my complete setup (tail servo to NEO, 1 cyclic servo to NEO, other servos to active RX outputs (RX is powered from NEO, so servos are powered through NEO, but not from cyclic ouputs) - to simulate equal power load) and i power on helicopter there is no problem, so BEC is working fine. Problem is only when is more than one cyclic servo connected to NEO before boot up. There must something happend during 6.4 update.
So i already filled service form and i will wait for reply :-) .
RV
28 December 2020 23:1228.12.2020 23:12
Please test as recommended. Get a 2s - or - get 2s voltage (carefully!!!) from your balancer leads for a check if they are strong enough.
Kontronik (especially known on older Kosmiks) powers the BEC up in 2 steps - and if Kontronik thinks about "hhmmm ... too much current draw in powerup" - it will shut off. This can happen due the servo caps loading behaviour at powerup.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
swalko
29 December 2020 07:5329.12.2020 07:53
This is not HV setup. But i understand where are you pointing Rainer. So i done it other way. To speed up Kosmik BEC bootup i paired another RX and connected it directly to Kosmik. There is not noticeable difference in speed how fast everything bootup, but practical difference is that it works this way!
So 6.4 must boot little faster, or there is other order of initialisation than in 6.3 (i use NEO AUX3 output for ESC) . But as result, 6.4 load BEC sooner and result is that BEC resets itself.
This setup works for years and much more than thousand flights with ZERO issues.
So what now?
1 mal bearbeitet. Zuletzt am 29.12.2020 08:37 von swalko.
RV
29 December 2020 18:2629.12.2020 18:26
Which RX was it?
Was it exactly the same wiring as with the NEO?
(Master, Slave, Servos)?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
swalko
29 December 2020 18:5929.12.2020 18:59
FrSky X4RSB.
Full setup, everything connected to NEO as usual with difference that RX is connected and powered directly from Kosmik - this way everything works and NEO boot correctly.
All the time i used RX connected and powered from NEO. But this not works after 6.4 update. I dont know if there is some delay in port initialisation on NEO (i use AUX3 routing to Kosmik master) or NEO boot too fast after update and BEC is not ready yet that time.
Kosmik will switch BEC from low power mode to full power only when receive correct signal.
But i am talking here about hundredth of second.
RV
30 December 2020 10:1030.12.2020 10:10
Hmmm ... this behaviour of the Kosmik was adressed a few years ago as it is not a good idea e.g. to init sensors with different voltages during powerup. So we just have to wait unless the voltage come up stable with our init.
But - a Warmstart as shown here will not be a result of this. So there must be something else wrong - and as long as it isn't tested with a battery direct on the NEO instead a BEC i stay still on the BEC as suspected item.
Anyway - if you would like to check the VBar in our service, no problem at all, probably makes sense to narrow it down too - just file a service case by clicking on the service icon at this device in your list here, fill out the forms (place a link to this thread for my colleques) and wait for response.
About 6.4 - the only thing which was added to the control loop is the Lightness - is the VBra on pro or pro/Rescue?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
swalko
30 December 2020 11:0630.12.2020 11:06
In a case of Kosmik, it is as is, this cant be changed and i only read about this problem until 6.4 NEO update.
So you wrote that NEO is waiting for stable voltage? If it is so, then in my case after 6.4 update it dont wait (or it looks so) or it detect voltage faster, or sensors are ready faster, or something other. But clearly BEC is not initialised and NEO power on servo outputs.
I use 5.6V voltage - default, because this is nonHV setup.
NEO is PRO RESCUE, but i tried all other available firmwares with no success.
Warmstart in log is a result of NEO loop of restarts when there is everything connected and RX is powered through NEO. NEO will try to boot, BEC is not ready, BEC restarts, NEO will log warmstart and this way still in loop. So NEO think/expect that BEC is ready, but it is not.
If i boot NEO with RX connected directly to Kosmik, there are no warmstars in log, because it simply works as it should.
I dont think that there is something damaged. Directly before 6.4 update i connected NEO to my pc and everything worked. Right after 6.4 update NEO was not able to boot correctly in same configuration.
Ports on NEO are not damaged too. On FrSky i can bind more RXs at same time. So i connected one RX directly to Kosmik and second one to NEO. Everything booted and worked, because BEC was ready due to directly connected RX.
I am 99% sure, if Uli will prepare modified firmware with short delay before NEO power on servo outputs, it will work.