← VBar Control Classic

YGE controller + U/I sensor for two loads with only one drive battery? Please clarify. translated

VBar Control › VBar Control Classic · Started by EchoMike on 22 January 2026 15:0222.01.2026 15:02
EchoMike 22 January 2026 15:0222.01.2026 15:02
Hello everyone,

I would like to know the best way to monitor my drive battery.
The situation is as follows:

In my Interceptor E620 I now fly a YGE Saphir 155 V2 and of course also use the telemetry of the controller.
In addition to the drive system, the helicopter also has an electric smoke system (EL-Smoke S Duo - i.e. with two vaporizers), which is also powered by the drive battery (6S / 5000 mAh).
Now I'm wondering if it would be possible to monitor the consumption of the smoke system using a U/I sensor in parallel with the drive train and to have corresponding announcements issued that would give me an indication of how much capacity has been consumed.
The controller doesn't automatically "see" the consumed capacity of the smoke system, which poses a risk to me.

Thanks for your help and greetings,

Matthias
machine-translated from German · Show original
RV 22 January 2026 19:2622.01.2026 19:26
If both (controller and UI) are installed, the UI is always the "winner" for battery management. So, if that's what you want, just branch off after the UI ;-)

But... 6s 5000mAh batteries - don't get any illusions about using Smoke EL batteries. Below 7000mAh you won't get any decent flight time.

The fact is (I had this for 4 years with my BO 105) that you're always "ready" to start vaping immediately. Switching it off makes no sense with a helicopter. And so you need about 2000mAh for 8 minutes of flight time just for the smoke generator...

=> I had an extra 3000mAh 6S battery in there. Extra weight for the fun... 2 kilograms then.

https://www.vstabi.info/forum/read.php?10,25374,page=17

I then removed it again; the extra weight is significant, and besides, the system has often become clogged with carbon deposits and had to be disassembled.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.




1 mal bearbeitet. Zuletzt am 22.01.2026 19:27 von RV.
machine-translated from German · Show original
EchoMike 23 January 2026 10:5923.01.2026 10:59
Hello Rainer,

Thanks for your feedback and the valuable information :-)
Then I will install the U/I sensor according to your recommendation.

Let's see how things develop with the smoker; there are other models where I could use the system.

Have a nice weekend and thanks again,

Matthias
machine-translated from German · Show original
EchoMike 1 February 2026 21:1801.02.2026 21:18
Good evening again,

I've noticed something in the last few days that I'd like to adjust properly:
I have "looped in" the U/I sensor as suggested.
Telemetry is working, however, both telemetry ports are currently transmitting. There is now one signal from the controller and one from the U/I sensor;
How and what do I need to configure in either the VBar Control (Classic) or the YGE controller PC software to receive only the outputs from the U/I sensor?
I'm only asking so I can set the parameters correctly from the start, because I don't want to risk programming any errors.

Thank you and best regards,

Matthias
machine-translated from German · Show original
RV 1 February 2026 21:5701.02.2026 21:57
Which announcement are you referring to?

The battery percentages that appear automatically in increments of 10? - Those actually come from the battery log.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
EchoMike 2 February 2026 04:0802.02.2026 04:08
Yes, that's right, the battery percentage announcement in increments of 10, that's the one I mean.
As soon as the first threshold is reached and "Battery 90%" is announced, another announcement follows seamlessly: "Battery 70%".
That's somewhat misleading.

Best regards,
Matthias
machine-translated from German · Show original
EchoMike 2 February 2026 15:3902.02.2026 15:39
Small addendum:

Using the YGE software, I saw that the controller still had "YGE" entered under "Telemetry".
I didn't change anything there because I thought the protocol could communicate with the VBar anyway if the YGE app was activated.
machine-translated from German · Show original
RV 3 February 2026 07:0403.02.2026 07:04
Ah... yes... what I wrote above only works with a VBar Control Touch or EVO. That's where I can do the override.

Since the app structure is different in that respect for VBC classic... unfortunately not.

Give me some time, I'll take a look and see if I can do anything about it with minimal effort. The Classic version is actually no longer being developed here, but we'll see, maybe it's still possible if it only takes a little time.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
EchoMike 3 February 2026 12:2303.02.2026 12:23
Hi Rainer, thanks for your reply.

If you happen to find a way to make the VBar Classic work, I would of course be extremely happy :-)
I'm certainly waiting with anticipation :-)

At this point I would like to express my sincere thanks for the truly great support you have provided - whether here in the forum or on the phone.
You always find a solution for every problem :-) :-)

Regards, Matthias
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless