← VBar Control Classic

Nick After-Echoes with Small Inputs V 8.1 translated

VBar Control › VBar Control Classic · Started by jgmeiner on 1 December 2025 21:3001.12.2025 21:30
jgmeiner 1 December 2025 21:3001.12.2025 21:30
Hi,

Here's the problem: I have two XL Power Specter V2s, one Nick Maxwell Edition and one World Champion Edition, each with Vstabi V 8.1. The WCE has MKS X8 servos installed, the NME GDW has BLS 992 servos on the swashplate. Both have stock POM dampers. Both swashplate servos are set to 166Hz, gain 84/92, maneuverability 112, and Venture 701 blades.
The WCE flies like a helicopter on a simulator. Absolutely clean, locks into place perfectly.
The NME clicks into place perfectly with crisp 45-degree pitch impulses, but if I only make very small, sharp pitch inputs, it wobbles a bit. Just a little pitch, then quickly back to center. This is most pronounced at 1550 RPM, then lessens at 1800, and almost disappears at 2000. If I cyclically reduce the I-gain to 35, the wobble disappears. I can't say for sure whether the overall flight performance is suffering because my fingers are currently too cold, but I'd rather not reduce the I-gain.

My question:
Why does the NME lock in perfectly after hard stops at 45 degrees (even with tic-tocs/sawtooth patterns, for example), but oscillate after small impulses? I can increase the gain to about 100 before the typical "gain-too-high oscillations" occur when I really lay on the sticks. Reducing the gain below 76 worsens the behavior.

I haven't tried version 8.2 yet, but I'd like to understand it... including how the I-Gain factor fits into it.

Thanks in advance for any tips.

Best regards,
Johannes
machine-translated from German · Show original
RV 1 December 2025 22:0701.12.2025 22:07
I would start with the optimizer. If it throws a wrench in the works, it could be that your agility setting is a bit too high (it starts with half). Try lowering it by 5 points.

Alternatively, there's the control response. You could reduce that slightly to better adjust the model's implementation capabilities.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
ulrich 1 December 2025 22:3701.12.2025 22:37
Rainer is referring to the direct share ;-) , but the suggestions are still just as correct.

So long... Uli
http://www.vstabi.de
machine-translated from German · Show original
jgmeiner 2 December 2025 09:5602.12.2025 09:56
Hi, thanks for the tips!
Adjusting the direct input/control behavior didn't help. BUT increasing the stop support to 60 from 20 has now fixed it. However, I have the feeling that the helicopter is reacting a bit more sluggishly. But I'll figure that out...
However, it is surprising that these two almost identical helix motors (except for the servos) behave so differently.
machine-translated from German · Show original
Eddi E. aus G. 2 December 2025 10:0702.12.2025 10:07
Good morning,

The servos are an integral part of the control loop, and they behave quite obviously quite differently.

For the sake of science :-) one could swap the servo sets between the helicopters and compare them ^^

What seems to make the whole thing even more exciting is that some people say things like "MKS bomb!" or "MKS get hot, wobble."
Similarly with Theta, we know quite well that these are parameters in the servo.
GDW, an F3C pilot reported, one of his machines pitch-wobbles with V8, in parallel to adjustments he received two more servo sets from his sponsor, with the 3rd one (with standard parameters in the VBar!) everything was OK according to him.
Then there's the question of Midi or Full-Size, which also cannot be answered definitively.

I always read along with great interest :-)

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
jgmeiner 2 December 2025 20:5502.12.2025 20:55
I actually have a set of MKS HBL 850 X8s here, and I'm going to install them... And then I'll report back!
machine-translated from German · Show original
jgmeiner 3 December 2025 05:4103.12.2025 05:41
One more question: Is the stop support the same as the stop gain at the rear? I have the feeling that changes of direction take longer with higher stop support.
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless