Hello,
This evening I went out briefly to test rotor blades and noticed a strange behavior from the VBAR Control EVO (or the Vstabi EVO).
Introductory remarks:
Vstabi is running the latest software (...157). And I also ran the app updater recently. But nothing much happened.
After connecting the battery and initializing, the battery selection screen appears. Once I selected the battery, I landed in the helicopter setup wizard.
See image.
I closed it with the X and was able to fly normally.
I restarted it several times. I also completely switched off the transmitter and restarted it.
The Wizard kept coming back.
At home I tested 3 other helicopters (all with EVO). The Wizard appeared on all three?
Something's not right here.
PS the other problem with the short pulse during startup (see previous post) with the YGE 205 still exists.
Regards, Thomas
This evening I went out briefly to test rotor blades and noticed a strange behavior from the VBAR Control EVO (or the Vstabi EVO).
Introductory remarks:
Vstabi is running the latest software (...157). And I also ran the app updater recently. But nothing much happened.
After connecting the battery and initializing, the battery selection screen appears. Once I selected the battery, I landed in the helicopter setup wizard.
See image.
I closed it with the X and was able to fly normally.
I restarted it several times. I also completely switched off the transmitter and restarted it.
The Wizard kept coming back.
At home I tested 3 other helicopters (all with EVO). The Wizard appeared on all three?
Something's not right here.
PS the other problem with the short pulse during startup (see previous post) with the YGE 205 still exists.
Regards, Thomas
Hallo,
heute Abend bin ich kurz raus um Rotorblätter zu testen und hatte ein merkwürdiges Verhalten der VBAR Control EVO (oder vom Vstabi EVO).
Einleitend:
Auf Vstabi ist st die aktuellste Software drauf (...157). Und zuletzt habe ich auch mal den App-Updater laufen lassen. Aber großartig passiert ist da nichts.
Nach Anstecken des Akkus und Intialisierung kommt ja die Akkuauswahl. Sobald ich den Akku ausgewählt habe landete ich im Heli Setup Wizard.
Siehe Bild.
Mit dem X habe ich es geschlossen und konnte ganz normal fliegen.
Ich habe es mehrs neu gestartet. Auch habe ich den Sender mal "komplett" ausgeschaltet und neu gestartet.
Immer wieder kam der Wizard.
Zuhause habe ich 3 andere Helis (alle mit EVO) getestet. Bei allen dreien kam der Wizard?
Irgendwas stimmt da nicht.
P.S. das andere Problem mit dem kurzen Impuls beim Hochlauf (siehe ges. Post) beim YGE 205 besteht noch.
Gruß Thomas
heute Abend bin ich kurz raus um Rotorblätter zu testen und hatte ein merkwürdiges Verhalten der VBAR Control EVO (oder vom Vstabi EVO).
Einleitend:
Auf Vstabi ist st die aktuellste Software drauf (...157). Und zuletzt habe ich auch mal den App-Updater laufen lassen. Aber großartig passiert ist da nichts.
Nach Anstecken des Akkus und Intialisierung kommt ja die Akkuauswahl. Sobald ich den Akku ausgewählt habe landete ich im Heli Setup Wizard.
Siehe Bild.
Mit dem X habe ich es geschlossen und konnte ganz normal fliegen.
Ich habe es mehrs neu gestartet. Auch habe ich den Sender mal "komplett" ausgeschaltet und neu gestartet.
Immer wieder kam der Wizard.
Zuhause habe ich 3 andere Helis (alle mit EVO) getestet. Bei allen dreien kam der Wizard?
Irgendwas stimmt da nicht.
P.S. das andere Problem mit dem kurzen Impuls beim Hochlauf (siehe ges. Post) beim YGE 205 besteht noch.
Gruß Thomas
machine-translated from German · Show original