Icuk73
16 April 2025 16:5416.04.2025 16:54
Hello,
I notice the following problem specifically with 2 helicopters.
When I switch on the motor, the motor/rotor initially spins up very rapidly (shortly after switching on), causing the corner to spin out of alignment. Then it gradually reaches the target speed.
These are the following helicopters with Vstabi-EVO-Gov.
1. Il Goblin Pro with YGE 205 and XNOVA 4535-460
2. Protos 800 EVO with YGE 205 and Combove 4735-410
With my other helicopters (Specter with Aureus, Nimbus with Saphir 125 and P380 with LV65) it boots up smoothly.
I've already reduced the ramp-up limit from 3 to 2.
I also set the VBAR's control menu to Smooth, but it has no effect.
Where can I influence the fact that there is less torque at the beginning?
I'm afraid my helicopter might tip over sometime.
Thank you.
Regards, Thomas
Edited once. Last edited on 16.04.2025 at 16:56 by Icuk73.
Hallo,
mir fällt speziell bei 2 Helis folgendes Problem auf.
Wenn ich den Motor einschalte, dann dreht der Motor/Rotor anfänglich (kurz nach einschalten) sehr heftig hoch, wobei es mir das Eck wegdreht. Dann geht es gemächlich bis zur Zieldrehzahl.
Es handelt sich um folgende Helis mit Vstabi-EVO-Gov.
1. Il Goblin Pro mit YGE 205 und XNOVA 4535-460
2. Protos 800 EVO mit YGE 205 und Combove 4735-410
Bei meinen anderen Helis (Specter mit Aureus, Nimbus mit Saphir 125 und P380 mit LV65) läuft das geschmeidig hoch.
Das Hochlauflimit habe ich schon von 3 auf 2 zurückgenommen.
Auch habe ich im Regler Menü der VBAR auf Smooth eingestellt, aber das wirkt null.
Wo kann ich das beeinfluss, dass am Anfang weniger Drehmoment vorhanden ist.
Ich fürchte, dass mir der Heli mal umkippt.
Vielen Dank.
Gruß Thomas
1 mal bearbeitet. Zuletzt am 16.04.2025 16:56 von Icuk73.
RV
16 April 2025 22:2516.04.2025 22:25
Was the VBar Governor Mode also set/checked in both the VBar AND the controller?
Otherwise – what about the motor switch? Which one? How is it operated? Does it have a safety switch?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Wurde auch in der VStabi UND im Regler der VBar Governor Mode gesetzt / geprüft?
Ansonsten - wie ist der Motorschalter? Welcher? Wie wird er bedient? Hats einen Sicherheitsschalter?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Icuk73
17 April 2025 09:2317.04.2025 09:23
Hello Rainner,
I believe that I selected VBAR/Mikado in both the controller software and the VBAR.
The safety switch is on the left side, the long one at the very bottom.
Motor switch to the right, above the long switch.
I'll double-check that.
What I've heard is that if you use VBAR-Gov, the settings like Smooth etc. in the YGE app are ineffective?!
Regards, Thomas
Hallo Rainner,
ich meine ja, dass ich Sowohl in der Reglersoftware als auch in der VBAR VSTABI/Mikado gewählt habe.
Sicherheitsschalter ist auf der linkens seite der der lange ganz unterste.
Motorschalter rechts der über dem langen Schalter.
Ich checke das nochmal.
Was ich mal gehört habe, ist, dass wenn man den VSTABI-Gov nimmt die Einstellungen mit Smooth usw. in der YGE-App wirkungslos sind?!
Gruß Thomas
RV
17 April 2025 12:3717.04.2025 12:37
With the VBar Gov, the controller has control over the start-up - and then switches to our ramp-up.
However, if the customer misuses the throttle by NOT programming and using the engine switch according to our recommendations, it is possible that AFTER the first start the engine will start up 10 times faster because the customer previously had the engine switch set to AR instead of OFF.
=> Is the MOTOR switch also turned OFF before the motor is turned ON?
Then there are those who use the safety switch to turn the motor on and off... also wrong. See the result above.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Beim VStabi Gov hat der Regler Kontrolle über den ANlauf - und blended nachdem auf unseren HOCHlauf um.
Wenn jetzt aber der Kunde das Gashandling falsch macht indem er den Motorschalter NICHT nach unserer Empfehlung programmiert und benutzt - kann es ein dass NACH dem 1. Start der HOCHlauf 10-fach schneller erfolgt da der Kunde zuvor NICHT den MOTORSchalter auf AUS - sondern auf AR hatte.
=> Wird der MOTORSchalter auch AUS gemacht bevor der Motor EINgeschaltet wird?
Dann gibts noch die Leute die mit dem Sicherheitsschalter den Motor an- und aus machen ... auch falsch. Ergebnis siehe oben.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
cc1975
17 April 2025 12:5517.04.2025 12:55
RV wrote:
-------------------------------------------------------
> Was also included in the VBar AND in the VBar controller
> Governor Mode set/checked?
>
I don't need to set the VBar Governor Mode in the controller, do I? It does that automatically because the app is installed and everything is learned "automatically," including the throttle positions, right?
RV schrieb:
-------------------------------------------------------
> Wurde auch in der VStabi UND im Regler der VBar
> Governor Mode gesetzt / geprüft?
>
Ich muss doch nicht im Regler den VBar Governor Mode setzen? Das macht der doch automatisch weil die App ja installiert ist und alles "automatisch" eingelernt wird, so wie auch die Gaswege?????
RV
17 April 2025 13:3917.04.2025 13:39
Quote: I don't need to set the VBar Governor Mode in the controller, do I?
Please check the ESC settings in the VBC file. You mentioned the old Classic version of VBC on the forum, and I don't have that version in front of me. I'm assuming that's the case – and checking it yourself with VBC shouldn't be too difficult.
For VBC touch and EVO it's clear - if the controller has been detected and the app is loaded BEFORE selecting it in the setup.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Quote:Ich muss doch nicht im Regler den VBar Governor Mode setzen?
Bitte mal nachsehen in der VBC beim ESC. Du schreibst bei VBC im Board (also die alte Classic) und die habe ich nicht gerade vor mir. Davon gehe ich aus - und nachsehen Deinerseits ist mit der VBC nicht wirklich schwierig.
VBC touch und EVO ists klar - wenn ZUVOR der Regler erkannt wurde und die App geladen ist BEVOR man im Setup das anwählt.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Icuk73
18 April 2025 18:1118.04.2025 18:11
Hello Rainer,
What do you mean by "incorrect throttle handling"?
I have the safety switch on 1 and the motor switch on 5.
Normally, I always switch off the safety features first and then switch on the engine.
I've attached some screenshots of the controller settings.
I also played around with the YGE menu in VBAR.
By long-pressing "Expert Settings", I changed the "Response" acceleration from medium to slow.
In the further menu, I experimented with the startup power setting by clicking briefly. The default setting is 0-10%.
I've tried different values here. I don't think it makes any difference.
I've already set the behavior to Smooth.
Thank you in advance.
Regards, Thomas
Hallo Rainer,
was meinst du mit "Gashandling falsch"?
ich habe die Sicherheit auf Schalter 1 und den Motor auf Schalter 5.
Normalerweise schalte ich immer zuerst die Sicherheit "aus" und dann schalte ich den Motor an.
Ich hab mal Screenshots von den Regler-einstellungen angehängt.
In der VBAR habe ich auch im YGE-Menü rumgespielt.
Bei einem langen Klick auf "Expert Einstellungen" habe ich die "Reaktion" Beschleunigung von mittel auf langsam gestellt.
Im weiteren Menü bei kurzen Klick habe ich mit der Anlaufleistung gespielt. Standardmäßig steht da ja 0-10 %.
Hier habe ich mit verschiedenen Werten rumprobiert. Ich finde da ändert sich nix.
Das Verhalten habe ich schon auf Smooth gestellt.
Vielen Dank im Voraus.
Gruß Thomas
RV
18 April 2025 20:0518.04.2025 20:05
Quote: Normally I always switch the safety off first and then I switch on the engine.
And does the motor switch go from OFF to ON? - Or from AR (center) to ON?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Quote:Normalerweise schalte ich immer zuerst die Sicherheit "aus" und dann schalte ich den Motor an
Und der Motorschalter geht dann auch von AUS nach EIN? - Oder von AR (Mitte) nach Ein?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Icuk73
18 April 2025 20:4118.04.2025 20:41
Hello Rainer,
From Off via AR to On.
I always do it that way.
Regards, Thomas
Hallo Rainer,
von Aus über AR zu Ein.
Hab das immer so.
Gruß Thomas
RV
20 April 2025 09:2820.04.2025 09:28
Is it possible to view a log of this somewhere in the cloud?
What does the gas bar do in the VBC?
What does the regulator opening do in parallel?
Is RPM also connected?
User screen display, possibly requiring the installation of an app:
- RPM Tele from VBar
- RPM aujs VSTabi RPM
- Gas from VBar
- Regulator opening from YGE
Take screenshots of the display, startup, and values (use the app with the switch for this), and attach them here in the thread.
Do you perhaps have the Pro Value Pack App Bundle with the option for custom telemetry on the VBC?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
1 mal bearbeitet. Zuletzt am 20.04.2025 09:28 von RV.
Kann man denn irgendwo ein Log davon sehen in der Cloud?
Was macht denn der Gasbalken in der VBC dabei?
Was macht parallel die Regleröffnung dabei?
Ist RPM auch angeschlossen?
Userscreen Anzeige, ggf. App dazu installieren:
- RPM Tele aus VStabi
- RPM aujs VSTabi RPM
- Gas aus VStabi
- Regleröffnung aus YGE
Das Anzeigen, Hochlauf und werte screenshotten (App dazu mit Schalter nutzen), hier anhängen im Thread.
Hast Du ev. das Pro Value Pack App Bundle mit Möglichkeit zur eigenen Telemetrie auf der VBC?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
1 mal bearbeitet. Zuletzt am 20.04.2025 09:28 von RV.
Icuk73
20 April 2025 20:2820.04.2025 20:28
I observed it more closely again yesterday.
It starts off softly for 3-6 revolutions, then suddenly accelerates really hard for a short time (1-2 seconds - then the rear end spins out "away" ;-) and then it slowly revs up to the target speed of bank 1.
With the Nimbus and sapphire 125 rotor, the rotor spins up very smoothly.
The settings in the Vbar are all set to default, as Homer already wrote above.
To Rainer:
Yes, can you look at my cloud? Or how can I send you the log?
If you can take a look, check out the Il Goblin Pro and the Protos 800 EVO.
RPM is all connected according to regulations.
I need to take another look at the other one.
I'll try again tomorrow without leaves.
Edited once. Last edited on 20.04.2025 at 20:31 by Icuk73.
Ich habe es gestern nochmal genauer beobachtet.
Er fängt 3-6 Umdrehungen soft an, dann schiebt er plötzlich kurz richtig an (1-2 Sekunden - da dreht Heck dann "Weg" ;-) und dann dreht er langsam zu Zieldrehzahl der Bank1 hoch.
Beim Nimbus mit Saphir 125 läuft der Rotor ganz homogen hoch.
Die Einstellungen in der Vbar sind jeweils auf default wie oben von Homer schon geschrieben .
An Rainer:
ja kannst du in meine Cloud reinschauen? Oder wie kann ich dir Log übermitteln.
Wenn du reinschauen kannst, dann schau dir den Il Goblin Pro und den Protos 800 EVO an.
RPM ist alles vorschriftsgemäß angeschlossen.
Das andere muß ich mir nochmal anschauen.
Ich probieres es morgen nochmal ohne Blätter.
1 mal bearbeitet. Zuletzt am 20.04.2025 20:31 von Icuk73.
RV
21 April 2025 00:0221.04.2025 00:02
So - I also had the 205 in my 800 - and it always started and revved up well.
A fellow club member is currently installing it in a scaler; perhaps Stephan (who is also here) can take another look at it without the leaves.
Please ALWAYS answer my questions! - This is often never done these days - but I have my reasons... so... first, this:
Quote: What does the gas bar do in the VBC?
What does the regulator opening do in parallel?
- RPM Tele from VBar
- RPM from VBar RPM
- Gas from VBar
- Regulator opening from YGE
Here's what you have: The Pro Value Pack app bundle with the option to create your own flight log. Just enter the values above there, without any switches, always on.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Also - ich hatte den 205er auch im 800er - und der lief immer gut an und hoch.
Ein Vereinskollege baut den gerade in einen Scaler ein, vielleicht kann Stephan (ist auch hier) das nochmal sich ohne Blätter dann ansehen.
Bitte IMMER meine Fragen beantworten! - Wird heute oft nie mehr gemacht - aber ich habe meine Gründe ... also ... erstmal das hier:
Quote:Was macht denn der Gasbalken in der VBC dabei?
Was macht parallel die Regleröffnung dabei?
- RPM Tele aus VStabi
- RPM aus VStabi RPM
- Gas aus VStabi
- Regleröffnung aus YGE
Das hast Du: Pro Value Pack App Bundle mit Möglichkeit zur eigenem Log beim Flug. Zimmere da mal obige Werte rein einfach ohne Schalter, immer an.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
RV
21 April 2025 21:0621.04.2025 21:06
https://www.vstabi.info/de/node/2489 Are there any videos on how to build your own log? ;-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
https://www.vstabi.info/de/node/2489
Gibts Videos wie man das eigene Log baut ;-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Icuk73
8 June 2025 10:2108.06.2025 10:21
Hello,
The problem is solved.
It appears that - for reasons unknown - the value of the "transition speed" changed from 235 to 247 in the last controller update.
Reset it and everything will work again.
Thanks to the people involved.
Regards, Thomas
Hallo,
das Problem ist gelöst.
Es hat sich scheinbar - unbekannterweise warum - beim letzten Regler Update der Wert der "Übergangsgeschwindigkeit von 235 auf 247 verändert.
Den zurückstellen und alles läuft wieder.
Danke an die betreffenden Personen.
Gruß Thomas
Icuk73
12 June 2025 12:2812.06.2025 12:28
Hello,
Yesterday I was able to test it with leaves.
Everything fits again.
So it was a control setting.
Regards, Thomas
Hallo,
gestern habe ich es mit Blättern testen können.
Alles paßt wieder.
War also eine Reglereinstellung.
Gruß THomas