christoph123
17 November 2025 17:0417.11.2025 17:04
Hello everyone
Search the shop for spare part 3051.
This is the blade bearing shaft.
Tail rotor.
Unfortunately, I can't find it; the search function didn't return any results either.
Thanks for the info
Regards
Hallo Gemeinde
Suche im Shop das Ersatzteil 3051
Es handelt sich um die Blattlagerwelle
Heckrotor.
Kann es leider nicht finden die Suchmaske ergab auch keine Treffer
Danke für die Info
MfG
Eddi E. aus G.
18 November 2025 09:0318.11.2025 09:03
Good morning,
The current hub is 04630, or the complete tail rotor is 04615.
If in doubt, I would take the complete tail rotor; I'm not sure what the differences are, and that way a) everything would be new, b) everything would be included, and c) it's probably cheaper overall than buying anything else separately.
Grüßle
Eddi
Born to fly ...
forced to work.
Moin,
die aktuelle Nabe ist 04630, oder der komplette Heckrotor 04615.
Im Zweifel würde ich den kompletten Heckrotor nehmen, ich bin gerade nicht sicher, was die Unterschiede sind, und damit wäre a) alles neu, b) alles dabei und c) ist's unter'm Strich vermutlich günstiger als noch was zu- oder nachzukaufen.
Grüßle
Eddi
Born to fly ...
forced to work.
Christoph68
18 November 2025 11:2618.11.2025 11:26
Hello,
Just a heads-up: if you use the 4630 hub, you'll also need to buy new bearings, because the hub diameter is 5 mm. The original L400/480 hub, part number 3051, was only 4 mm in diameter. Alternatively, you could check if another dealer has the 3051 in stock.
greeting
Christoph
Hallo,
nur als Hinweis: wenn Du die Nabe 4630 nimmst, musst Du auch die entsprechenden Lager neu kaufen, weil der Durchmesser der Nabe 5 mm beträgt. Die Original-Nabe vom L400/480 mit Nummer 3051 hatte nur 4 mm im Durchmesser. Oder halt schauen, ob noch ein anderer Händler die 3051 vorrätig hat.
Gruß
Christoph
Eddi E. aus G.
18 November 2025 11:3918.11.2025 11:39
Christoph helps Christoph, I like it :-)
Yes, that's it, 4 mm vs. 5 mm.
How quickly one forgets 1 mm :-)
I think screws and thrust washers were also discussed.
—Eddi
Born to fly ...
forced to work.
Christoph hilft Christoph, I like :-)
Ja das war's, 4 mm vs. 5 mm.
Wie schnell man 1 mm vergisst :-)
Ich glaube Schrauben und Anlaufscheiben waren da auch noch Thema.
—Eddi
Born to fly ...
forced to work.
Christoph68
18 November 2025 12:0418.11.2025 12:04
Hello,
Yes, we help each other out. That's one of the purposes of a forum. Back to the topic: if I saw correctly, the thrust bearing is the same, but not the ball bearings and the spacer between the front ball bearing and the thrust bearing. The screw for attaching the blade holder is also stronger (M3 vs. M2.5), but the washer between the rear blade holder screw and the thrust bearing is omitted. Now all the details should be clear.
greeting
Christoph
Hallo,
ja, man hilft sich. Das ist ja u.a. der Sinn eines Forums. Back to topic: wenn ich es richtig gesehen habe, ist das Drucklager gleich, nicht jedoch die Kugellager und die Distanzscheibe zw. vorderem Kugellager und Drucklager. Auch die Schraube zur Befestigung des Blatthalters ist stärker (M3 vs. M2,5), dafür entfällt die Unterlegscheibe zw. Heckblatthalterschraube und Drucklager. Jetzt sollte alle Details auf dem Tisch liegen.
Gruß
Christoph