← Logo 400 ... 690

Update to version 8.2 translated

Mikado Model Helicopters › Logo 400 ... 690 · Started by klauserg on 31 August 2026 13:0531.08.2026 13:05
klauserg 31 August 2026 13:0531.08.2026 13:05
Over the weekend I updated all my VBAR to the latest software version.
The Logo 600 and Goblin 700 work perfectly, but the Logo 200 V8 was barely flyable after the update.
Reloading the presets (I tried all three: Sport/3D/extreme 3D) didn't help either.
In the end, the only thing that helped was to massively reduce the sensitivity of the rear and TS (they are now at 40 and 50 respectively).

Question 1:
Is this "new" behavior really a result of the update, or do I need to look for another error?
I already searched, but found nothing obvious, and the last flight before the update was completely normal.

Question 2:
Do I really have to update the motor controller according to these instructions https://www.vstabi.info/en/l200esc so that I can build on the values I've already set up? Note: I find the instructions good, but it's actually a mess if you have to do it that way; it doesn't correspond to Mikado's USP that everything is controlled via the VBAR. I would have expected something better from Mikado.

Question 3:
How can I reset the Vstabi to its factory settings if I absolutely have to update the controller when using version 8.2?

Question 4:
Where could I have seen before the update that a controller update was also required in addition to the Vstabi update?
I didn't notice anything unusual before, during, or after the update. I only saw that the settings needed to be checked.

Thanks
machine-translated from German · Show original
Eddi E. aus G. 31 August 2026 14:0431.08.2026 14:04
Hi,

Version 8.2 works best with the controller update to 1.9, and then with the preset from 'New Model Setup'.
The sub-settings Sport/3D etc. unfortunately work worse than expected (because micro helicopters simply have an extremely narrow window of values where they work great), we need to work on that again, but are still waiting for input from certain pilots.

Unfortunately, it's true that no matter which controller (OMP like here, or Hobbywing, or YGE, or-or-or) 'follows its own (update) rules'.
We're just glad it works at all; it would be worse if they weren't user-upgradeable (by users or us), then you'd need a new controller to use the advanced firmware...

Otherwise, you could just go back to version 7.x, load a new setup and the corresponding settings, trim it, then everything will be as it was before.

:-) Here on our homepage, since May, almost everything has revolved around 8.2, micro helicopters, tuning tips and the guide for the switchover.
And as far as I know, there were also one or two reports in the news app on the channel, I don't recall them right now.
But... no 'warning', attention, if you have this helicopter you need this or something :-/

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
klauserg 31 August 2026 19:2331.08.2026 19:23
Thanks for the reply. I guess I'll have to piece together the update stuff myself.

Best regards
Gerhard
machine-translated from German · Show original
Eddi E. aus G. 1 September 2026 08:5101.09.2026 08:51
Good morning,

Or... you send the helicopter around.

I have no idea if you'll need the BT stuff a second time, unless you have other OMP products where it also works.

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
klauserg 1 September 2026 09:0301.09.2026 09:03
Okay, thank you and have a nice day.
Gerhard
machine-translated from German · Show original
klauserg 3 September 2026 08:5203.09.2026 08:52
I have another question:
I wanted to install your setup using VBar Evo Setup 7.1.
Unfortunately, the PC no longer connects to Vstabi due to driver problems.
I have worked through the forum post https://www.vstabi.info/forum/read.php?53,210681 , but have not found a solution.

Therefore, my question is:
If I create a new model with VBAR Control and then download the preset for the Logo 200 2025 V8, will I get a setup that works well right away with the new ESC firmware 1.9, or do I need to adjust anything else besides the trimming (e.g., controller to digital, jitter filter, optimizer, and whatever else can be found in the entries here)?
Thanks in advance!
machine-translated from German · Show original
Eddi E. aus G. 3 September 2026 09:5703.09.2026 09:57
Good morning,

No offense, but what is it you all keep doing with the computer?
It is only valid if you are flying with a third-party transmitter (up to V7).
There are no presets there either.

Updating with VBar Control Manager might be faster than via Wi-Fi and radio, OK, but otherwise... please keep the device off!

:-) *puppy eyes*

The downloadable setup is V8 (!) and compatible with controller firmware 1.9 _if_ you didn't have it on your transmitter (back then, (as of 01-07-2026)).

Now, let's be constructive:

VBar V7 with non-updated ESC 1.4, bind, model setup, new model setup, LOGO 200, wait, trim swashplate horizontally (Setup/Trim), have a good flight!

VBar V8 with non-updated ESC 1.4, bind, model setup, new model setup, Mikado new, ESC firmware old LOGO 200 (refers to the ESC firmware!), wait, trim swashplate horizontally, set 0° pitch (fold blades; setup/trim), have a good flight!

VBar V8 with updated ESC 1.9, bind, model setup, new model setup, Mikado new, ESC firmware new LOGO 200 (refers to the ESC firmware!), wait, trim swashplate horizontally, set 0° pitch (fold blades; setup/trim), have a good flight!
-> There will also be a written announcement on the transmitter and a QR code here.

Then you don't have to change anything; the helicopter flies like it's brand new.

One could also do this, but it's not absolutely necessary:

https://www.vstabi.info/de/update_8_2_2
https://www.vstabi.info/de/v8_microheli

Please do _not_ use the first 3-dot menu on the 2nd model screen (scroll down one page) (basic setups for ...), these are too general and do not work well or at all on micro helicopters.

If you want to adjust things, you can set the RPM, maneuverability and (rotation) rate (like Dual Rate) there, or also the expo in the (...) menus for the main and tail rotor.

Of course, you can always experiment/try to optimize for your flying style :-)

So far, so good :-)

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
klauserg 3 September 2026 12:1903.09.2026 12:19
Thanks

I only wanted to use the PC because I thought the download you linked would be different from what I get via the Control Panel. If that's not the case, then everything's clear. :-)
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless