Rainer2019
28 December 2025 17:3628.12.2025 17:36
Hello,
What can you do with the new macrocell "Latch" (see
https://www.vstabi.info/de/update_release_nov_2025 )?
Regards, Rainer
Hallo,
was kann man mit der meuen Makrozelle "Latch" anfangen (siehe
https://www.vstabi.info/de/update_release_nov_2025)?
Gruß Rainer
RV
28 December 2025 20:3228.12.2025 20:32
This allows you to define and lock a state as a start condition. If this state is not reached, nothing happens.
For example, to prevent an EZFW (retractable landing gear) from accidentally retracting when plugged in, the switch should be in the "retracted" position. It can only be retracted after the switch has been in the "extended" position once.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Hiermit kan man einen Zustand als Startbedingung festlegen und verriegeln. Wenn dieser nicht erreicht ist wird nix gemacht.
Z.B. für ein EZFW so dass es beim anstecken nicht aus versehen einfährt sollte der Schalter auf "eingefahren" stehen. Erst wenn der Schalter dann einmal auf "ausgefahren" stand lässt es sich einfahren.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
JMalberg
28 December 2025 23:1328.12.2025 23:13
Good morning,
Is the last state of the "latch" cell also retained in the VBAR if the VBAR was switched off?
So, as the name suggests, it's a lock that only opens when a pin is pulled? Like "Remove Before Flight" tags.
Regards, Jürgen
(Here are the missing commas for free use in my posts: ,,,,,,,,, )
Moin,
der letzte Zustand der "Latch"-Zelle wird dann in der VBAR auch gehalten, wenn die VBAR ausgeschaltet war?
Ist also wie der Name schon sagt, ein Riegel der erst öffnet, wenn ein Stift gezogen wurde? Wie "Remove Before Flight"-Tags.
Gruß Jürgen
( hier noch die fehlenden Kommata zu freien Verwendung in meinen Beiträgen: ,,,,,,,,, )
Rainer2019
29 December 2025 12:5829.12.2025 12:58
You don't need a latch for that, because you can achieve it with the existing macrocells (trigger + multiplexer).
Dazu braucht es doch kein Latch, denn das kann man doch mit den vorhandenen Makrozellen auch erreichen (Trigger + Multiplexer).
ulrich
29 December 2025 16:0229.12.2025 16:02
Currently, the status isn't maintained; instead, enabling it implies that everything has been properly configured with the "Remove before Flights" options after the flight. However, it would certainly be possible to implement this feature.
It's certainly possible to achieve this differently with a little imagination, but for example, there's a message if the model's state isn't correct after being switched on. This allows you to force the default position of important switches. This is already implicit in the motor switch.
So long... Uli
http://www.vstabi.de
Derzeit wird der Satus nicht gehalten, sondern ein Einschalten impliziert, das man nach dem Flug alles ordentlich mit den "Remove before Flights" bestückt hat. Es wär aber durchaus eine Möglichkeit, das noch zu machen.
Man kann das sicher mit etwas Fantasie auch anders hinbekommen, aber es gibt z.B. eine Meldung, wenn nach dem Einschalten des Modells der Zustand nicht passt. Damit kann man die Grundstellung wichtiger Schalter erzwingen. Beim Motorschater ist das ja schon implizit.
so long ... Uli
http://www.vstabi.de
Rainer2019
2 January 2026 17:2902.01.2026 17:29
Is it possible to do that with imagination too?
So far, I've only ever managed it using logic.
Edited 1 time(s). Last edit at 01/02/2026 05:58PM by Rainer2019.
Mit Fantasie geht das auch?
Ich habe es bisher immer nur mit Logik geschafft.
Edited 1 time(s). Last edit at 01/02/2026 05:58PM by Rainer2019.