Good morning
I have a Vstabi RX-Only here which I use to control the counterpart via S-Bus.
I chose S.Bus as the basic setup; my default is now a typical area layout.
I need to adjust the output channels because the other end expects input on predefined channels. I then ventured into the macro cells and made some initial attempts. I wanted to output, for example, the bank switch via S.Bus on channel 5, so I selected macro cell Ch5, changed it to channel 5, and selected the corresponding switch. It's not working somehow, but I'm sure it's possible; I just don't know how. I also need to output channels 1-4, like with a helicopter. Can you give me a hand? I'll dig through VTube again and see if I can find anything else that might help me.
VG
Edited 3 time(s). Last edit at 04/01/2026 05:09PM by Teci.
I have a Vstabi RX-Only here which I use to control the counterpart via S-Bus.
I chose S.Bus as the basic setup; my default is now a typical area layout.
I need to adjust the output channels because the other end expects input on predefined channels. I then ventured into the macro cells and made some initial attempts. I wanted to output, for example, the bank switch via S.Bus on channel 5, so I selected macro cell Ch5, changed it to channel 5, and selected the corresponding switch. It's not working somehow, but I'm sure it's possible; I just don't know how. I also need to output channels 1-4, like with a helicopter. Can you give me a hand? I'll dig through VTube again and see if I can find anything else that might help me.
VG
Edited 3 time(s). Last edit at 04/01/2026 05:09PM by Teci.
Moin
Ich habe hier ein Vstabi RX-Only mit dem ich über S-Bus das Gegenstück ansteuere.
Als Grundsetup habe ich S.Bus gewählt, als Standard habe ich jetzt eine Typische Flächenbelegung.
Ich müsste jetzt die Kanäle der Ausgabe anpassen da die Gegenstelle Eingaben auf Vorgegebenen Kanälen erwartet. Habe mich dann mal an die Macrozellen getraut und die ersten Versuche unternommen, ich wollte erreichen das zum Beispiel der Bankumschalter über S.Bus auf Kanal 5 ausgegeben wird also hab ich die Macrozelle Ch5 ausgewählt sie auf Kanal umgestellt und den Schalter dazu ausgewählt. Klappt irgendwie nicht bin mir aber Sicher das es geht nur wie. Ich müsste auch Kanal 1-4 wie beim Heli ausgeben, könnt ihr mir auf die Sprünge helfen, ich wühle mich nochmal durch Vtube und schaue ob ich noch was finde was mich vieleicht weiter bringt ;-)
VG
Edited 3 time(s). Last edit at 04/01/2026 05:09PM by Teci.
Ich habe hier ein Vstabi RX-Only mit dem ich über S-Bus das Gegenstück ansteuere.
Als Grundsetup habe ich S.Bus gewählt, als Standard habe ich jetzt eine Typische Flächenbelegung.
Ich müsste jetzt die Kanäle der Ausgabe anpassen da die Gegenstelle Eingaben auf Vorgegebenen Kanälen erwartet. Habe mich dann mal an die Macrozellen getraut und die ersten Versuche unternommen, ich wollte erreichen das zum Beispiel der Bankumschalter über S.Bus auf Kanal 5 ausgegeben wird also hab ich die Macrozelle Ch5 ausgewählt sie auf Kanal umgestellt und den Schalter dazu ausgewählt. Klappt irgendwie nicht bin mir aber Sicher das es geht nur wie. Ich müsste auch Kanal 1-4 wie beim Heli ausgeben, könnt ihr mir auf die Sprünge helfen, ich wühle mich nochmal durch Vtube und schaue ob ich noch was finde was mich vieleicht weiter bringt ;-)
VG
Edited 3 time(s). Last edit at 04/01/2026 05:09PM by Teci.
machine-translated from German · Show original