← Cafe

Tail rotor -> Tail Extended -> Control loop parameters translated

Public Talk › Cafe · Started by TanzderBlätter on 5 May 2026 20:3105.05.2026 20:31
TanzderBlätter 5 May 2026 20:3105.05.2026 20:31
Hello dear pilots,

Is it possible to assign a fixed value to the I limiter on a switch?

Greetings from Austria!
Paul Klinkenhammer
machine-translated from German · Show original
RV 5 May 2026 21:2905.05.2026 21:29
Not directly, but it could be adjusted via bank transfer.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
TanzderBlätter 5 May 2026 23:3605.05.2026 23:36
Dear Mr. Vetter,

Thank you for your reply. The idea behind my question is that when I initialize the helicopter on the table at the flying field and then carry it to the launch site, the tail isn't centered. During takeoff, the tail then swings away. I wanted to fix this with the switch. Simply set the I limiter to 5 -> activate the switch and the tail is perfectly aligned for takeoff.

Greetings from Austria!
Paul Klinkenhammer
machine-translated from German · Show original
Eddi E. aus G. 6 May 2026 09:0006.05.2026 09:00
Hi Paul,

Please just use the stick, that's what it's there for ;-)

Position the model, set the tail blades to 0° or minimally against the torque, and off you go.

You can hear and see it when the engine starts up; if the rear end generates unusual thrust, then simply correct it slightly.

Otherwise, use banks, a ramp-up bank with I-limit or, better yet, I-discharge – the latter reduces the I to zero over a certain period of time as long as nothing else is accumulating, and does not limit the heading hold like I-limit or even I-limit (normal mode).

Quote: TdB
to run away

New word creation :-)

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
RV 6 May 2026 12:2206.05.2026 12:22
I know another trick using bank 4, but I'll have to try it out later.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
TanzderBlätter 7 May 2026 19:4407.05.2026 19:44
Hello Eddi and Rainer,

I've now implemented it via AR-Bank and I'm completely satisfied with this solution!
Thank you so much for your support!

Greetings from Austria!
Paul Klinkenhammer
machine-translated from German · Show original
RV 7 May 2026 21:5007.05.2026 21:50
Ahhh... now... and I haven't even tried it yet... but great!

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless