nick77
22 May 2026 20:5922.05.2026 20:59
hey hey,
I have a problem with my speed controller in my RAW 580. I can't reach the set speeds (the helicopter is brand new).
oppset:
xnova lightning l4025/3y-560 8p
hobbywing platinum 180a v5
batteries 2x 6s 2800mah and 2x 6s 3300mah
I set the motor to 22 pinions, gear ratio 9.40 and 8n poles/4 pole pairs.
bank1 is 2000 umin, bank2 is 2200 umin and bank3 is 2400 umin.
I reach approximately 1500 rpm and a little more in banks 2 and 3.
Where could the problem be here?
mfg Kai
hei hei,
ich habe ein problem mit meinem drehzahlregler in meinem raw 580.ich erreiche die eingestellten drehzahlen nicht(der heli ist ganz neu).
oppset:
xnova lightning l4025/3y-560 8p
hobbywing platinum 180a v5
batterien 2x 6s 2800mah und 2x 6s 3300mah
eingestellt habe ich 22 ritzel am motor, gear ratio 9.40 und 8n pole/4 polpaare.
bank1 sind 2000umin, bank 2 2200umin und bank 3 2400umin.
ich erreiche ca 1500umin und ein bisschen mehr in bank 2 und 3.
wo kann hier das problem sein?
mfg kai
RV
22 May 2026 22:3422.05.2026 22:34
Which government is being used? VBar, I think?
Was the RPM measured or just read?
- What is the controller opening status in the HW Info/Status?
Are there any logs from the test run in the cloud? What is the serial number of the VBC/Stabi?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
- welcher Gov wird verwendet? VStabi denke ich?
- wurde die RPM nachgemessen oder nur abgelesen?
- wie ist dann die Regleröffnung im HW Info/Status?
- gibt es logs auf der Cloud vom Testlauf? Seriennummer VBC/Stabi?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
nick77
22 May 2026 22:5922.05.2026 22:59
Hey Reiner
Yes, the vstabi gov is used.
The engine speed is only displayed on the screen, but is noticeably/audibly low.
I can't tell you anything about the regulator opening because I don't know what that means.
I can answer your questions about the logs and serial number tomorrow.
If I increase the base throttle to 70-80-90 in the speed control menu, I roughly reach the desired speed. But I don't think that's the solution.
Kind regards, Kai
Hei Reiner
Ja der vstabi gov wird benutzt.
Die drehzahl wird nur im display abgelesen, ist aber spürbar/hörbar gering.
Zur regleroeffnung kann ich dir nichts sagen, weil ich nicht weiss was das bedeutet.
Zu den logs und seriennr, kann ich dir morgen antworten.
Wenn ich im drehzalregler meny das basisgas auf 70-80-90 erhoehe, komme ich ca auf die gewünschte drehzahl. Aber ich denke, das das nicht die lösung ist.
Mfg kai
RV
22 May 2026 23:1322.05.2026 23:13
Quote: Are there logs from the test run on the cloud? Serial number of VBC/Stabi?
Quote: - What is the controller opening status in the HW Info/Status?
Click the HW icon on the VBC to view the information during the test run.
The question is – if I read this correctly:
Is the RPM input also connected to the stabilizer?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Edited 2 time(s). Last edit at 05/22/2026 11:16PM by RV.
Quote:- gibt es logs auf der Cloud vom Testlauf? Seriennummer VBC/Stabi?
Quote:- wie ist dann die Regleröffnung im HW Info/Status?
HW Icon auf der VBC anklicken, Infos beim Probelauf dort anschauen.
Preisfrage - wenn ich das so lese:
Ist der RPM input auch am Stabi dran?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Edited 2 time(s). Last edit at 05/22/2026 11:16PM by RV.
nick77
23 May 2026 17:1623.05.2026 17:16
Hey Rainer,
It was actually just the RPM connector that had come loose.
Because I already had a speed reading, I would never have thought to check the connector :-)
thank you very much for your help.
mfg Kai
hei rainer,
es war tatsaechlich nur der rpm stecker der sich geloest hatte.
weil ich ja eine drehzahl hatte, waehre ich nie darauf gekommen, den stecker zu ueberpruefen :-)
vielen dank fuer deine hilfe.
mfg kai
RV
23 May 2026 18:0423.05.2026 18:04
Hoi Kai,
Great!
You can always test this by unplugging the TELE cable and then checking if RPM is still displayed. TELE takes priority for the display; RPM is the fallback. However, we need the fast RPM input for the Gov (government module).
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Hoi Kai,
prima!
Man kann das immer testen indem man den TELE abzieht und dann schaut ob noch RPM angezeigt wird. Fürs Display hat TELE vorrang, Fallback ist RPM. Für den Gov brauchen wir aber den schnellen RPM Eingang.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.