Racerbuk
28 May 2026 19:4728.05.2026 19:47
Hello everyone
I have a Vario Cobra 800. I did my first test flights today. Initially, it was very twitchy on all control surfaces, especially pitch. I experimented with all sorts of settings that I thought would be useful, and it flies much better than before, but I'm still not completely satisfied. The helicopter isn't as stable in the air as, for example, my 700-size Agusta with Align mechanics. Do I just need to get used to it? I'm running at just under 1500 RPM at the rotor head, and it only takes off at about 3/4 pitch. With the pitch stick in the center position, I have -2.3 degrees of deflection, and the maximum pitch is 13 degrees. The blades are 800-size S-shaped. I've attached some photos showing my current transmitter settings.
I'd really appreciate any tips, it's my first 800.
Edited 2 time(s). Last edit at 05/28/2026 08:55PM by Racerbuk.
Hallo zusammen
Ich habe eine Vario Cobra als 800er. Heute die ersten Flugversuche gemacht. Sie war anfangs sehr nervös auf allen Rudern, vor allem auf Nick. Ich hab mal mit allen möglichen Einstellungen hantiert die ich für sinnvoll erachte, er fliegt damit um welten besser als zuvor, aber so richtig glücklich bin ich noch nicht. Der Heli liegt nicht so stabil in der Luft wie ich es z.B. von meiner 700er Agusta mit Alignmechanik kenne. Muss ich mich erst an das Teil gewöhnen? Ich habe am Kopf knapp 1500 umin und sie hebt erst ab ca 3/4 Pitch ab. In Mittenstellung des Pitchknüppels hab ich - 2.3 Grad anliegen, max Pitch ist 13 Grad. Die Blätter sind 800er S-Schlag. Ich hab mal paar Fotos angehängt wie die Sendereinstellungen gerade sind.
Bin für Tipps echt dankbar, ist mein erster 800er
Edited 2 time(s). Last edit at 05/28/2026 08:55PM by Racerbuk.
Racerbuk
28 May 2026 19:4828.05.2026 19:48
Racerbuk
28 May 2026 19:5328.05.2026 19:53
Photos didn't work somehow from my phone
Edited 1 time(s). Last edit at 05/28/2026 08:07PM by Racerbuk.
Fotos, ging irgendwie vom Handy nicht
Edited 1 time(s). Last edit at 05/28/2026 08:07PM by Racerbuk.
Fingolf
28 May 2026 20:0628.05.2026 20:06
What's your weight?
I can gladly provide my Airwolf setup. It's at
10kg and very stable in the air.
Stephan
Was hast du da für ein Gewicht?
Kann sonst gerne mein Airwolf Setup zur Verfügung stellen. Der ist bei
10kg und sehr stabil in der Luft.
Stephan
Racerbuk
28 May 2026 20:0828.05.2026 20:08
Approximately 10 kg as well; the settings of your Bell would be interesting.
Greetings Günter
Edited 1 time(s). Last edit at 05/28/2026 08:54PM by Racerbuk.
In etwa auch 10 kg, die Einstellwerte von Deiner Bell wären schon interessant
Grüsse Günter
Edited 1 time(s). Last edit at 05/28/2026 08:54PM by Racerbuk.
RV
28 May 2026 22:3428.05.2026 22:34
If you have a VBar EVO - install V8 and work with the Control Response ;-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Wenn Du eine VStabi EVO hast - mach V8 drauf und arbeite mit der Control Response ;-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Racerbuk
28 May 2026 22:3828.05.2026 22:38
Unfortunately not, only the "old" Neo...
But it should still be flyable, right?! A few tips regarding my settings (photo) would be really helpful. The helicopter isn't very stable in the hover; I'll try a trim flight. Does the optimizer make any difference?
Greetings Günter
Edited 2 time(s). Last edit at 05/28/2026 10:43PM by Racerbuk.
Leider nein, nur das „alte“ Neo ..
Aber sollte doch auch damit fliegbar werden, oder ?! Paar Tipps in Bezug auf meine Einstellungen ( Foto) wären echt hilfreich. Irgendwie ist der Heli nicht stabil in der Schwebe, werde auch mal einen Trimmflug starten. Bringt der Optimierer was ?
Grüsse Günter
Edited 2 time(s). Last edit at 05/28/2026 10:43PM by Racerbuk.
RV
29 May 2026 06:3829.05.2026 06:38
Well, that's hard to say, it's been a long time since the NEO and V6. The V8 on the EVO is significantly better, as I noticed with my UH-1D.
But if it's "indifferent", the question arises as to what brings more integral and also possibly to massively reduce the direct component (optimizer) (approx. 1/4 to 1/3 maneuverability), instead flying more via gain.
How heavy is the helicopter, what RPM is it running at, where is the stabilizer installed, and what does the vibration analysis in the VBC show while hovering?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Naja - das ist schwer zu sagen, ist schon lange her mit NEO und V6. V8 auf EVO ist da um einiges besser geworden, hatte ich bei meiner UH-1D so festgestellt.
Aber wenns "indifferent" ist stellt sich die Frage was mehr Integral bringt und auch ev. den Direktanteil (Optimierer) massiv (Ca. 1/4 bis 1/3 Wendigkeit) zu reduzieren, dafür mehr übers Gain fliegen.
Wie schwer ist der Heli denn, welche RPM liegt an, wo ist die Stabi verbaut, was sagt die Vibrationsanalyse in der VBC im Schweben?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Racerbuk
29 May 2026 07:4529.05.2026 07:45
Hello Rainer
It weighs about 10 kg, the VBar is mounted in front of the rotor head, about 15 cm in front of it. It's not showing any vibrations. The RPM is at 1450; I had the feeling that it didn't do much below that.
PS: I've already reduced the maneuverability to 48.
Edited 2 time(s). Last edit at 05/29/2026 07:53AM by Racerbuk.
Hallo Rainer
Sie wiegt etwa 10 kg, die VStabi ist vorm Rotorkopf verbaut, etwa 15 cm davor. Vibs zeigt sie keine an. Die Drehzahl ist bei 1450 umin, hatte das Gefühl drunter tut sich recht wenig
P.s. Bei der Wendigkeit bin ich eh schon auf 48 runter
Edited 2 time(s). Last edit at 05/29/2026 07:53AM by Racerbuk.
Fingolf
29 May 2026 08:5229.05.2026 08:52
Here are my values.
V7:
Flight values Cyclical
Exponential 28 28 28 10
Maneuverability 74 74 74 90
Sensitivity 80 80 80 80
Style 100 100 100 100
Lightness 0 0 0 0
Nick precompensation 10 10 10 10
Paddle Simulator 0 10 10 10
Integral 60 60 60 60
Pitch pump 0 0 0 0
Pitch Balance -1 -1 -1 -1
Optimizer 37 37 37 45
Helicopter size ----- ----- 80 ----- -----
V8:
Flight values Cyclical
Exponential 10 10 10 10
Maneuverability 38 38 38 50
Direct share 19 19 19 50
Tax behavior 20 20 20 22
Sensitivity 88 88 88 72
Integral 70 70 70 70
Pitch Balance 35 35 35 35
Stop Support 20 20 20 20
You'd almost have to see/fly it to find out why it doesn't quite fit.
Otherwise, I would also suggest the main focus.
As you can see, the benches are completely identical; only the rotational speed has minimal differences.
My V8 is slightly better, but the Airwolf was always top-notch even with the V6/V7 Neo/Evo.
Stephan
Hier mal meine Werte.
V7:
Flugwerte Zyklisch
Exponential 28 28 28 10
Wendigkeit 74 74 74 90
Empfindlichkeit 80 80 80 80
Style 100 100 100 100
Leichtigkeit 0 0 0 0
Nick Prekompensation 10 10 10 10
Paddelsim 0 10 10 10
Integral 60 60 60 60
Pitchpump 0 0 0 0
Pitch Balance -1 -1 -1 -1
Optimierer 37 37 37 45
Heligröße ----- ----- 80 ----- -----
V8:
Flugwerte Zyklisch
Exponential 10 10 10 10
Wendigkeit 38 38 38 50
Direktanteil 19 19 19 50
Steuerverhalten 20 20 20 22
Empfindlichkeit 88 88 88 72
Integral 70 70 70 70
Pitch Balance 35 35 35 35
Stop Unterstützung 20 20 20 20
Man müsste das fast mal sehen/fliegen um ggf. rauszufinden warum es nicht ganz passt.
Sonst würde mir noch der Schwerpunkt einfallen.
Die Bänke siehst ja, sind komplett gleich, nur Drezhahl hab ich minimale Unterschiede.
Bei mir ist die V8 eine Kleinigkeit besser, aber auch mit V6/V7 Neo/Evo lag der Airwolf immer Top.
Stephan
RV
29 May 2026 09:0429.05.2026 09:04
First, please mount the stabilizer in a suitable location in such a way that it only absorbs the rotational movement of the helicopter and cannot be disturbed by vibrations, flap around, or be further stimulated by an attachment on top ;-)
The best place is on a wooden board or similar in the fuselage floor. The mechanics are always the worst place. There, it absorbs all the vibrations the mechanics produce, including those that the NEO analysis might not even detect. This affects precision – sometimes more, sometimes less – but always to some extent.
The stabilizer should rest flat and stably. Flat isn't really the case here – and stable with the "screw-in plate mounting method"... I don't know.
Please remove the antennas from the stabilizer! - Such a swaying Tower of Babel isn't good either. Many people do it that way, but they're simply doing it wrong in terms of vibration.
1450 rpm should be fine – but it also depends on the blades. My Bo runs at 1240 rpm at 10 kg with an 800 NHP symmetrical, 4-blade propeller, so it's comparable.
How were the 8 degrees determined?
Do you have zero pitch at stick center and symmetrical pitch paths or "scale-like" - and if the latter - how was it done?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Montiere bitte als erstes die Stabi an eine vernünftige Stelle in einer Art und weise dass sie möglichst nur das Drehverhalten des Helis aufnimmt und nicht von Vibrationen doch gestört werden kann, herumschlabbern kann und mit einem Aufsatz obendrauf noch angeregt wird ;-)
Im Rumpfboden auf ein Holzbrett o.Ä. am Besten. An der Mechanik ist immer der schlechtere Platz. Da bekommt sie alles ab was die Mechanik an Vibrationen hergibt, auch welche die die Analyse der NEO hier ggf. gar nicht anzeigen kann. Darunter leidet die Präzision - mal mehr, mal weniger - aber eben immer etwas.
Die Stabi sollte da auch flächig uns stabil aufliegen. Flächig ist hier auch net so ganz - und stabil mit der "Einschraubenplattenbefestigungsmethode" auf Nick ... ich weiß net.
Die Antennen bitte auch runter vom Stabi! - So ein schwingender Turmbau zu Babel ist auch net gut. Machen viele so, machen sie dann halt schwingungstechnisch einfach falsch.
1450 1/min sollten schon ok sein - kommt aber auch auf die Blätter an. Meine Bo hat 1240 1/min an 10 kg bei 800er NHP symmetrisch und 4-Blatt, ist somit vergleichbar.
Wie wurden denn die 8 Grad ermittelt?
Hast Du Nullpitch bei Knüppelmitte und symmetrische Pitchwege oder "Scale-like" - und wenn letzteres - wie gemacht?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Racerbuk
29 May 2026 09:3429.05.2026 09:34
Hello Rainer
I'll relocate the stabilizer away from the mechanics; there's plenty of room for it. I've zeroed the mechanics cyclically. Does it absolutely have to be 8 degrees, or can I lower it so that the roll and pitch deflections are smaller? I've programmed the helicopter for scale from the start; the center position is 2.3 degrees.
Greetings Günter
Hallo Rainer
Das Stabi verlege ich dann runter von der Mechanik, Platz ist genug dafür da. Zyklisch hab ich an der Mechanik genullt. Muss das unbedingt 8 Grad sein oder kann ich auch runter damit so dass die Ausschläge auf Roll und Nick kleiner werden ? Programmiert habe ich den Heli von Anfang an auf Scale, in der Mitte liegen 2.3 Grad an
Grüsse Günter
Racerbuk
29 May 2026 09:3629.05.2026 09:36
PS I made the pitch curve steeper at the beginning and flatter towards the top.
P.S. Pitchkurve habe ich Anfangs steiler und nach oben hin flacher gemacht
JMalberg
29 May 2026 11:4929.05.2026 11:49
Hi Günter,
Always mount the VBR securely, without any additional components, onto a stable plate that is exactly perpendicular to the rotor shaft in all axes.
8° is an essential reference for the system; not 7.5° and not 8.4°. Tip: If you have a digital pitch meter, check if it displays the same value when you rotate it 180°. ;-)
Believe me! It cost me a lot of batteries and nerves before I accepted this 8° reference point, especially with "sluggish" scalers. The reaction isn't immediate like with agile 3D helicopters, but rather delayed, and you end up wasting your time trying to find the right setting.
The shifted pitch curve ultimately just causes problems, since the 0° pitch then has to be manually adjusted again (and I had to search for that for ages in the setup menus). I only use linear curves now, which are perhaps only slightly flattened below 0° pitch.
Could it be that your servo travel is limited in VBAR because otherwise the servo would bottom out? That was the biggest source of wobbly behavior on one of my scale models. Therefore, maximize servo travel in VBAR and compensate mechanically with shorter servo arms.
Regards, Jürgen
(Here are the missing commas for free use in my posts: ,,,,,,,,, )
Hi Günter,
Das VBR immer fest ohne alles auf eine stabile Platte montieren, die genau senkrecht in allen Achsen zur Rotorwelle liegt.
8° sind eine unabdingbare Referenz für das System; keine 7,5° und keine 8,4°. Tipp: Bei einem digitalen Pitchmesser prüfen, ob er wenn du ihn um 180° drehst auch den gleichen wert anzeigt. ;-)
Glaub 's mir! Es hat mich viele Akkus und Nerven gekostet, bis ich gerade bei "trägen" Scalern diese 8°-Referenz akzeptiert habe. Da kommt die Reaktion nicht wie bei agilen 3D-Helis direkt sondern irgendwie und etwas später und du suchst dir nen Wolf.
Auch die verschobene Pitchkurve macht letztendlich nur Ärger, da dann auch die 0°-Pitch wieder manuell angepasst werden muss (und das musste ich in den Setup-Menüs echt lange suchen). Ich benutze nur noch lineare Kurven, die evtl nur <0° Pitch etwas abgeflacht sind.
Kann es sein dass deine Servowege im VBAR eingeschränkt sind, weil sonst das Servo anschlägt? Das war an einem meiner Scaler die größte Fehlerquelle für wabbeliges Verhalten. Deshalb möglichst viel Servoweg im VBAR und mechanisch durch kürzere Servohebel ausgleichen.
Gruß Jürgen
( hier noch die fehlenden Kommata zu freien Verwendung in meinen Beiträgen: ,,,,,,,,, )
Racerbuk
29 May 2026 12:1229.05.2026 12:12
Hello Jürgen
I'll reposition the stabilizer now. I always check the deflections with the digital pitch gauge. There are plenty of deflections, but nothing is stuck. The collective pitch is at 8 degrees, measured multiple times. I'll program the pitch curve to be linear at 0 degrees at the center and then flatten it out slightly above the center for better responsiveness.
By "perpendicular to all axes," you probably mean that the stabilizer bar shouldn't be mounted off-center, right? So, aligned with the rotor shaft... and not offset to the side.
VG Günni
Edited 2 time(s). Last edit at 05/29/2026 12:16PM by Racerbuk.
Hallo Jürgen
Das Stabi werde ich jetzt versetzen. Die Ausschläge kontrolliere ich grundsätzlich mit der digitalen Pitchlehre. Ausschläge sind reichlich vorhanden, anstehen tut das nirgends. Kollektiver Pitch ist bei 8 Grad, mehrfach gemessen. Pitchkurve werde ich mal linear programmieren bei 0 Grad auf Mitte und dann etwas abflachen über Mitte für mehr Reaktion.
Mit senkrecht zu allen Achsen meinst Du wahrscheinlich dass das Stabi nicht aussermittig montiert werden sollte , oder? Also fluchtend zur Rotorwelle.. und nicht seitlich versetzt
VG Günni
Edited 2 time(s). Last edit at 05/29/2026 12:16PM by Racerbuk.
JMalberg
29 May 2026 14:0529.05.2026 14:05
@Racerbuk Orthogonal to the HaRo axis but not necessarily centered / aligned with the axis.
In my Hughes, the VBAR is located on the right side and in front of the HaRo shaft, but exactly perpendicular to it.
Regards, Jürgen
(Here are the missing commas for free use in my posts: ,,,,,,,,, )
@Racerbuk Orthogonal zur HaRo-Achse aber nicht zwingend mittig / fluchtend zur Achse.
In meiner Hughes sitzt das VBAR seitlich rechts und vor der HaRo-Welle, aber eben genau senkrecht zu ihr.
Gruß Jürgen
( hier noch die fehlenden Kommata zu freien Verwendung in meinen Beiträgen: ,,,,,,,,, )
Eddi E. aus G.
29 May 2026 14:2629.05.2026 14:26
Good morning,
Being off-center is no problem at all, the rotation rate °/sec is just as fast at the pivot point as at the extreme end.
That wouldn't even work on all axes ;-)
—Eddi
Born to fly ...
forced to work.
Moin,
außermittig ist überhaupt kein Problem, die Drehrate °/sek ist ja im Drehpunkt genauso schnell wie am äußersten Ende.
Ginge ja auch gar nicht auf allen Achsen ;-)
—Eddi
Born to fly ...
forced to work.
Racerbuk
29 May 2026 16:3729.05.2026 16:37
Would the settings on the HRW work as shown in the photos? Or are fundamental changes necessary?
Würden die Einstellungen auf der HRW so passen wie auf den Fotos gepostet ? Odersind da grundsätzliche Änderungen notwendig. ?
Racerbuk
31 May 2026 09:0531.05.2026 09:05
Hello Jürgen,
I mostly copied the settings changes from your Neo; there weren't any significant differences to my settings. I need to experiment a bit in the field; a test flight is still pending.
@Rainer, the VBar is now mounted laterally in the lower fuselage area in the direction of flight, antennas are guided on the fuselage wall and the cables and the stabilizer are securely attached to a painted wooden bulkhead with 3M 0.5mm VHB.
The center of gravity is perfectly balanced, but lies absolutely perfectly on the rotor axis. The cyclic pitch is exactly 8 degrees, zero pitch is precisely at the stick center and at 13 degrees at the top and 7 degrees at the bottom. Zeroed at the mechanism in front of the rotor head with a digital pitch gauge, and both blades were measured above the boom (exactly the same values). Nothing is rubbing. The curve is set slightly steeper in the middle and then flatter at the top so that it lifts its tail more easily and quickly.
The weight is 10520g including all batteries, rotor blades are Vario 800 S-type.
I think I just need to get used to the flight characteristics; my 700-size Agusta weighs 6100g ready to fly. That's a huge difference. When the 800-size motor moves in any direction, it's a completely different mass pushing against it.
I hope the weather is suitable for another test flight next week, calm winds, I would like to do a trim flight then.
Greetings Günni
Edited 2 time(s). Last edit at 06/01/2026 10:41PM by Racerbuk.
Hallo Jürgen,
Hab die Änderungen bei den Einstellungen grösstenteils von Deiner Neo Übernommen, gravierende Unterschiede zu meinen Einstellungen waren da nicht. Muss mich mal rantasten am Feld, Testflug steht noch aus.
@Rainer , das VStabi ist jetzt im unteren Rumpfbereich seitlich in Flugrichtung montiert, Antennen an der Rumpfwand geführt und die Kabel sowie das Stabi wackelfrei auf einem lackiertem Holzspannt mit 3M 0.5mm VHB befestigt.
Der SP ist noch mal ausgewogen, liegt aber absolut perfekt auf der Rotorachse. Der Zyklische ist bei exakt 8 Grad, Nullpitch genau in Knüppelmitte und oben bei 13 Grad, unten 7. Genullt an der Mechanik vorm Rotorkopf mit digitaler Pitchlehre und beide Blätter jeweils überm Ausleger gemessen ( exakt gleiche Werte ) . Anstehen tut nirgends was. Die Kurve ist über Mitte etwas steiler gestellt und dann oben flacher damit er leichter und schneller den Hintern hochnimmt.
Gewicht liegt übrigens bei 10520g inkl allen Akkus, Rotorblätter sind Vario 800er SSchlag.
Denke ich muss mich einfach auch an das Flugverhalten rantasten, im Vergleich liegt meine 700er Agusta bei 6100g abflugfertig. Ist schon ein gewaltiger Unterschied. Wenn der 800er eine Bewegung in irgendeine Richtung macht, dann schiebt halt eine ganz andere Masse an.
Hoffe das Wetter passt um nächste Woche mal einen weiteren Testflug zu machen , windstill, möchte da einen Trimmflug starten.
Grüsse Günni
Edited 2 time(s). Last edit at 06/01/2026 10:41PM by Racerbuk.
RV
31 May 2026 13:0231.05.2026 13:02
Yep - the key data is good.
With profiled blades, however, there's one thing we always have to consider – their response isn't linear. This applies both to control and to flying. For example, if you come into a flare, you'll notice that they don't initially "catch" when you recover. Just calmly add more pitch... it's a matter of practice.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Edited 1 time(s). Last edit at 05/31/2026 01:03PM by RV.
Jupp - die Eckdaten sind gut.
Bei profilierten Blättern haben wir allerdings immer eines zu berücksichtigen - sie sind nicht linear im Ansprechverhalten. Zum Einen für die Regelung, zum anderen beim Fliegen. Kommst Du z.B. im Flare rein wirst du bemerken dass sie zuerst nicht "greifen" beim Abfangen. dann einfach ruhig Pitch nachschieben ... ist ne Übungssache.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Edited 1 time(s). Last edit at 05/31/2026 01:03PM by RV.
Racerbuk
31 May 2026 13:2231.05.2026 13:22
Yes, I have to approach it carefully. He's not a coach, but it'll be alright.
Greetings Günter
Ja, muss mich da vorsichtig ranrasten. Ist halt kein Trainer, aber wird schon.
Grüsse Günter
Eddi E. aus G.
1 June 2026 08:5901.06.2026 08:59
Good morning,
...The term "zero pitch" is somewhat misleading: with symmetrical blades, 0° means zero lift and minimum drag, which is also the reversal point for torque compensation at the tail. With a lifting airfoil, the angle is slightly less than 0°. It's minimal, but you can feel/notice it.
What I found more unpleasant was that I perceived a difference in the circular/aerobatic flight on the taxi, compared to the trainer.
Conversely, it didn't bother me that Scale is left-handed and Trainer is right-handed...
Grüßle
Eddi
Born to fly ...
forced to work.
Moin,
... Nullpitch ist da auch etwas missverständlich: bei symmetrischen Blättern ist 0° null Auftrieb, geringster Widerstand, was auch der Umkehrpunkt für den Drehmomentausgleich am Heck ist, bei tragendem Profil liegt das Winkelmäßig etwas unter 0°. Ist minimal, spürt/merkt man aber.
Ich fand unangenehmer, dass ich damit im Rundflug/Kunstflug auf Roll eine Differenzierung wahrgenommen habe, im Vergleich zum Trainer.
Umgekehrt hat's mir nix ausgemacht, dass Scale Linksdreher und Trainer Rechtsdreher sind ...
Grüßle
Eddi
Born to fly ...
forced to work.
Racerbuk
1 June 2026 22:4401.06.2026 22:44
Hi Eddi,
So, at zero pitch, the blade angle is approximately -2?
Greetings Günni
Hallo Eddi,
Also bei Nullpitch Blattanstellung bei -2 etwa ?
Grüsse Günni
Eddi E. aus G.
2 June 2026 09:0202.06.2026 09:02
Hi Günni,
That certainly depends on the sheet; I believe it was most likely -1.00 on the SAB sheets, which we first had on the BOs, but which we replaced quite quickly with symmetrical NHP sheets.
It doesn't have to be 1000% perfect, you can actually hear/see it quite well on the ground if you steer a little 'through zero', then you can set 'zero pitch' at the stick position.
In scale flying, this hardly matters for the control loop, but if, for example, you quickly switch from negative to positive or quickly reduce pitch, and if the zero point for torque compensation is not correct, the tail will become a little unstable (pulls slightly or veers slightly).
With today's servos and control loops, it's probably hardly noticeable anymore, but I lack a comparison.
Grüßle
Eddi
Born to fly ...
forced to work.
Moin Günni,
das hängt sicher vom Blatt ab, –1-komma waren's glaube ich am ehesten bei den SAB, die wir als erstes auf den BOs hatten, die wir aber recht schnell durch symmetrische NHP ersetzt haben.
1.000-%ig muss es sicher nicht sein, man hört/sieht es eigentlich ganz gut am Boden, wenn man ein wenig 'durch Null steuert', bei der Knüppel-Position kann man dann 'Nullpitch' setzen.
Beim vorbildgetreuen Fliegen fällt das kaum in's Gewicht, für den Regelkreis, aber wenn man bspw. schnell von negativ nach positiv durchsteuert, oder schnell Pitch wegnimmt, und wenn der Nullpunkt für den Drehmoment-Ausgleich nicht stimmt, wird das Heck halt ein wenig unruhig (schiebt etwas, oder weicht etwas aus).
Mit heutigen Servos und dem heutigen Regelkreis vermutlich kaum mehr wahrnehmbar, da fehlt mir aber der Vergleich.
Grüßle
Eddi
Born to fly ...
forced to work.
Racerbuk
3 June 2026 21:4303.06.2026 21:43
Hello everyone
I flew today and was extremely satisfied. I did a trim flight and it was the icing on the cake. Thank you all for the helpful tips. Wishing you a happy holiday and great flights!
Greetings Günni
Edited 1 time(s). Last edit at 06/03/2026 10:44PM by Racerbuk.
Hallo zusammen
Heute geflogen und äusserst zufrieden. Hab einen Trimmflug gemacht und der war das i-Tüpfelchen. Danke euch allen für die hilfreichen Tipps. Wünsche euch einen schönen Feiertag und tolle Flüge
Grüsse Günni
Edited 1 time(s). Last edit at 06/03/2026 10:44PM by Racerbuk.