Simon_75
16 June 2026 13:0516.06.2026 13:05
Hello
I have flown many flights with (Bank1,2,3) 1700/1800/1900, 70% Bank 2. However, I have always wondered why I had to switch to the highest 24-tooth pinion to achieve a controller opening of 75-85% in hovering flight.
During the maiden flight, I uploaded a picture of the motor to Chstgpt and compared it to the datasheet. Both specified a pole pair of 5.
I then asked the same question on Google and the answer was that the number is 4. A picture of the engine and the answers are attached.
Based on feel, the correct setting should be 4, as I am hovering at 2200 revolutions at 75%.
I could actually fly by feel and throttle setting, but I'm still interested in knowing what the correct RPM is.
Does anyone know the engine and the correct settings?
Best regards, Simon
Hallo
Ich bin viele Flüge mit (Bank1,2,3) 1700/1800/1900 geflogen, 70% Bank 2. Ich habe mich jedoch immer gewundert, dass ich auf das höchste 24er Ritzel wechseln musste, um auf eine Regleröffnung von 75-85% im Schwebeflug zu kommen.
Ich hatte beim Erstflug ein Bild vom Motor bei Chstgpt eingegeben und mit dem Datenblatt verglichen. Beide haben ein Polpaar von 5 angegeben.
Nun habe ich die gleiche Frage bei Google gestellt und die Antwort war, die Anzahl seien 4. Ein Bild vom Motor und die Antworten sind im Anhang.
Vom Gefühl müsste die richtige Einstellung 4 sein, da ich so im Schweben bei 2200 Umdrehungen bei 75% liege.
Eigentlich könnte ich nach Gefühl und Regleröffnung fliegen, trotzdem interessiert es mich, welche Drehzahl wirklich stimmt.
Kennt jemand von euch den Motor und die richtige Einstellung?
LG Simon
Eddi E. aus G.
16 June 2026 14:0116.06.2026 14:01
Hi Simon,
If you ask AIs, you can probably end up taking the weighted average :eyeroll: and counting the clicks until you lose it ^^
Scorpion itself (and who would know better...) specifies the 4025-1100 as having 10 poles (=5 pole pairs).
No guessing game with Jimiri...
But to be able to calculate, some information is still missing:
Rated speed = 3.7 V * 6 cells * 1,100 KV * 24 (pinion) / unknown (main gear)
Maximum regulated speed from full to empty (according to my four-finger-rolled-one-on-top rule) = rated speed * 0.8 (6s drives) or * 0.9 (12s drives)
It's not an exact science, but it works in most cases.
So, and now comes an absolute phenomenon :-) ... the batteries are fully charged at 4.2 V/cell.
This means that the throttle opening at that speed will probably/based on experience be at 60-65% at the beginning.
For the sake of the regulator, it shouldn't be set any lower...
As the battery/voltage decreases, it increases, but always remains 'well in control' (80-90%), so that under load (full cyclic-full pitch-yay!) there is still enough control reserve to maintain the speed even then and with an almost empty battery.
And then comes the dark side of the force, which is designed for maximum speed and power, but then, from about 1-2/3 of the battery charge onwards, lives with the controller almost always being 100% open (which isn't even a bad thing in this case), or rather, that at some point the speed simply follows the voltage and drops...
That's why you usually see the most aggressive flying at the beginning of a race, when the battery is still full, and then more relief at the end.
Grüßle
Eddi
Born to fly ...
forced to work.
Moin Simon,
wenn Du KIs fragst, kannst Du am Ende vermutlich das gewichtete Mittel nehmen :augenroll: und Einrasten zählen bis Du ausrastest ^^
Scorpion selbst (und wer wüsste es besser ...) gibt den 4025-1100 mit 10 Polen (=5 Pol-Paare) an.
Kein rate mal mit Jimiri ...
Aber um rechnen zu können, fehlen noch Angaben:
Nenndrehzahl = 3,7 V * 6 Zellen * 1.100 KV * 24 (Ritzel) / unbekannt (Hauptzahnrad)
Max. geregelte Drehzahl von voll bis leer (nach meiner Vier-Finger-eingerollt-einer-oben-drauf-Regel) = Nenndrehzahl * 0,8 (6s Antriebe) oder * 0,9 (12s-Antriebe)
Is keine exakte Wissenschaft, haut aber in den meisten Fällen hin.
So, und jetzt kommt noch ein absolutes Phänomen :-) ... die Akkus haben voll geladen 4,2 V/Zelle.
D. h. die Regleröffnung bei der Drehzahl wird vermutlich/erfahrungsgemäß zu Beginn bei 60-65 % liegen.
Sollte dem Regler zuliebe auch nicht niedriger liegen ...
Mit leerer werdendem Akku/abnehmender Spannung geht sie dann immer höher, bleibt aber immer 'gut in den Federn' (80-90 %), so dass bei Last (voll zyklisch-voll Pitch-yay!) noch genug Regelreserve da ist, um die Drehzahl auch dann und bei nahezu leerem Akku zu halten.
Und es kommt die dunkle Seite der Macht, die auf maximale Drehzahl und Leistung auslegt, dann aber ab ca. 1-2/3 des Akkus damit lebt, dass der Regler fast immer auf 100 % offen ist (was in dem Fall nicht mal schlecht ist) bzw. dass dann irgendwann die Drehzahl einfach der Spannung folgt und fällt ...
Deswegen sieht man in Küren auch meist das aggressivste Fliegen am Anfang, wenn der Akku noch voll ist, und am Ende dann mehr Entlastungen.
Grüßle
Eddi
Born to fly ...
forced to work.
Simon_75
16 June 2026 14:2116.06.2026 14:21
My Goblin 570 has two stages:
1. Main gear = 62 / Pinion 18
2nd gear (with freewheel) 60 | Motor pinion 24
Set translation: 8.61
With this gear ratio and 5 pole pairs, I'd be hitting the limit at 2000 RPM (100% under load). Larger pinions aren't available. Could it be that the motor has 4 pairs? When rotating 360 degrees, it engages strongly 24 times.
Attached is a data sheet.
Mein Goblin 570 hat zwei Stufen:
1. Hauptzahnrad = 62 / Ritzel 18
2. Zahnrad (mit Freilauf) 60 | Motorritzel 24
Eingestellte Übersetzung: 8.61
Mit dieser Übersetzung und 5 Pol Paare wäre ich bei 2000 Umdrehungen am Anschlag (100% bei Last) . Größere Ritzel gibt es nicht. Kann es nicht sein dass der Motor 4 Paare hat? Beim drehen um 360Grsd rastet er 24 mal stark ein.
Im Anhang noch ein Datenblatt
Eddi E. aus G.
16 June 2026 15:0416.06.2026 15:04
Hey,
exciting :-)
With us... 10/5 ->
https://shop.mikado-heli.de/Elektronik/Motoren/Motor-Scorpion-HKIII-4025-1100.htm?a=article&ProdNr=04349&p=4753 The engine in the picture doesn't yet have the Mikado branding, nor the fluted bell; it's not an HKIII.
If there was an 8/4-pole version before that (before 2010?), I'm not aware of it.
Scorpion may be able to determine this using the serial number.
But now let's look at the bill:
3.7 * 6 * 1.100 / 8.611 = 2.836 rpm nominal speed without load * 0.8 = 2.269 rpm expected continuously adjustable speed under load ... that sounds plausible to me.
However, this combination doesn't quite fit into SAB's table for the 570 (see attachment).
Something's not right here ;-)
Grüßle
Eddi
Born to fly ...
forced to work.
Edited 2 time(s). Last edit at 06/16/2026 03:15PM by Eddi E. aus G..
Hej,
spannend :-)
Bei uns ... 10/5 ->
https://shop.mikado-heli.de/Elektronik/Motoren/Motor-Scorpion-HKIII-4025-1100.htm?a=article&ProdNr=04349&p=4753
Der Motor im Bild hat auch noch nicht das Mikado-Branding, nicht die geriffelte Glocke, ist kein HKIII.
Falls es davor (vor 2010?) noch einen 8/4-Poler gab, ist mir das nicht geläufig.
Ggfs. kann Scorpion das anhand der Seriennummer noch ermitteln.
Aber jetzt mal die Rechnung:
3,7 * 6 * 1,100 / 8,611 = 2.836 1/min Nenndrehzahl ohne Last * 0,8 = 2.269 1/min zu erwartende durchgehend regelbare Drehzahl unter Last ... das klingt für mich plausibel.
Die Combo passt aber auch irgendwie wieder nicht in die Tabelle von SAB für den 570-er (Anlage).
Irgendwas stimmt da nicht ;-)
Grüßle
Eddi
Born to fly ...
forced to work.
Edited 2 time(s). Last edit at 06/16/2026 03:15PM by Eddi E. aus G..
RV
16 June 2026 18:4216.06.2026 18:42
That's correct, the motor was available a loooooong time ago as an 8-pole (4 pole pairs)... I even had it in the Logo 500. But that was 10 years ago!
Tip:
Check the RPM with an external tachometer at the rotor head, and then you'll see if it's set incorrectly.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Edited 1 time(s). Last edit at 06/16/2026 06:49PM by RV.
Das ist richtig so, dem Motor gab es gaaaaaaaaaaanz früher als 8-Poler (4 Polpaare) ... hatte ich auch im Logo 500 mal. Ist aber schon 10 Jahre her!
Tip:
RPM mit einem externen Drehzahlmesser nachprüfen am Rotorkopf und dann sieht mans auch wenn das falsch eingestellt ist.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Edited 1 time(s). Last edit at 06/16/2026 06:49PM by RV.
Simon_75
16 June 2026 18:4516.06.2026 18:45
According to your calculation, it should be an 8-pole system, if I understand correctly. I've sent an inquiry to Scorpio.
Thank you
Gemäß Deiner Berechnung müsste es ein 8 Pol sein, sofern ich es richtig verstanden habe. Ich habe eine Anfrage an Skorpion gesendet.
Vielen Dank
Eddi E. aus G.
17 June 2026 10:3217.06.2026 10:32
Yes, from that perspective that would make sense.
The HKIII has been listed with us since 04-2010, replacing the previous one (which was on sale roughly between 09-2008 and 10-2010).
I might have had one of those in my 500 series at the beginning :-) but back then it didn't really matter, because... no practical telemetry anyway, and I think the governor only became hip from version 5.0 onwards in 2010, and even then only with an external speed sensor and suitable (non-red) controllers.
Ah, those were the days! ^^
—Eddi
Born to fly ...
forced to work.
Ja, so gesehen würde das Sinn ergeben.
Der HKIII ist bei uns aber auch schon seit 04-2010 gelistet, ersetzte den vorherigen (im Verkauf etwa zwischen 09-2008 bis 10-2010).
Womöglich hatte ich auch so einen am Anfang im 500-er :-) aber damals war's tatsächlich noch Latte, weil ... keine praktikable Telemetrie eh nicht, und der Governor wurde meine ich erst ab Version 5.0 und in 2010 hip, und auch nur mit ext. Drehzahlsensor und geeigneten (nicht roten) Reglern.
Hach, waren das noch Zeiten ^^
—Eddi
Born to fly ...
forced to work.
Simon_75
17 June 2026 11:3417.06.2026 11:34
Hier die Antwort von Skorpion:
Hello,
This motor is 8 Pole. So 4 Pole Pair.
BR
Kyle Dahl
LG Simon
Eddi E. aus G.
17 June 2026 12:0317.06.2026 12:03
Super!
And who's training the AI with this now, 'Jibbidy, did you know?' ^^ :-)
—Eddi
Born to fly ...
forced to work.
Super!
Und wer trainiert jetzt die KI damit, 'Jibbidy, wusstest Du schon?' ^^ :-)
—Eddi
Born to fly ...
forced to work.
Simon_75
17 June 2026 14:0317.06.2026 14:03
AI should be approached with caution; it doesn't make us smarter, but rather more convenient?
KI ist mit Vorsichtig zu genießen, sie macht uns noch klüger sondern bequemer?????