Firefly
23 June 2026 12:2123.06.2026 12:21
Hello,
I use the Mini Vstabi together with the Hobywing 60A V4 controller.
VGov also works, however, the log always shows the message "Speed controller does not switch reliably".
The sensor cable from the Hobbywing is connected to Rx A, the controller input to Rx B.
What could that be?
Hallo,
ich verwende das Mini Vstabi zusammen mit dem Hobywing 60A V4 Regler.
VGov funktioniert auch, allerdings habe ich im Log immer die Meldung Drehzahlregler schaltet nicht sicher um.
Das Sensorkabel vom Hobbywing hängt an Rx A, Reglereingang auf Rx B.
Was könnte das sein?
Eddi E. aus G.
23 June 2026 15:1523.06.2026 15:15
Good morning,
It's possible that the signal level is too weak, and that's why the signal isn't switching reliably, with the levels fluctuating from low to high to low to a stuttering low to high to low... or there might be a loose connection, a faulty cable, a damaged connector, etc.
Are the entries sporadic or constant?
Counter-test loopback test: take a patch cable and connect the signal, e.g., from the tail servo output of the VBar, to RX A (not +/– ...).
Then a low speed should be displayed immediately (servo pulse / gear ratio / number of poles).
If no messages are displayed, then the signal input of the VBar is OK; then it must be something else.
Grüßle
Eddi
Born to fly ...
forced to work.
Moin,
es kann schon sein, dass der Signalpegel zu schwach auf der Brust ist, und dass deswegen eben das Signal 'nicht sicher umschaltet', Pegel Low-High-Low-Hust-Low-High-Low ... oder es ist ein Wackler drauf, Kabel schadhaft, Stecker, ...
Kommen die Einträge sporadisch, oder ständig?
Gegenprobe Loopback-Test: mal ein Patchkabel hernehmen, und Signal bspw. vom Heckservo-Ausgang der VStabi auf RX A stecken (nicht +/– ...).
Dann müsste sofort eine niedrige Drehzahl angezeigt werden (Servopuls / Übersetzung / Polzahl).
Wenn dann keine Meldungen angezeigt werden, ist der Signal-Eingang der VStabi OK, dann muss es was anderes sein.
Grüßle
Eddi
Born to fly ...
forced to work.
Firefly
23 June 2026 19:1523.06.2026 19:15
Hi,
The entries accumulate throughout the entire flight.
Like I said, if I hadn't looked at the log, I wouldn't have noticed it.
Hi,
die Einträge summieren sich den ganzen Flug über auf.
Wie gesagt hätte ich nicht ins Log geschaut, hätte ich es nicht bemerkt.
Eddi E. aus G.
24 June 2026 09:2024.06.2026 09:20
Hm, OK.
There might actually be interference on the signal line, or the signal might not be stable/strong enough.
In principle, if everything else works and you know what you're doing, you can fly like that. I would just make sure that the base throttle and pitch adjustments are suitable for flight without a governor (unplug the RPM cable, set a good hovering speed with the base throttle, and then use the cyclic and pitch adjustments to create a rough V-curve that allows you to fly and land safely even without a governor).
It happened to me, the RPM signal dropped out (still with an external phase sensor...), the RPM dropped to around 700-800 RPM, and that briefly woke me up ^^
Another disadvantage is that the log is pretty useless when it's full of these entries; important ones that would otherwise be more noticeable might get lost.
—Eddi
Born to fly ...
forced to work.
Hm, OK.
Womöglich stört wirklich etwas auf der Signalleitung, oder das Signal ist nicht stabil/stark genug.
Im Prinzip, wenn's sonst funktioniert und man um die Sache weiß, kann man so fliegen. Ich würde nur schauen, dass Basisgas und Pitchzugaben für einen Flug ohne Governor passen (RPM-Kabel mal ausstecken, mit Basisgas eine gute Schwebedrehzahl einstellen, mit zyklischer- und Pitchzugabe eine grobe V-Kurve malen, mit der man auch ohne Governor zumindest sicher fliegen und landen kann.
Mir passiert, Drehzahlsignal weggefallen (noch mit ext. Phasensensor ...), Drehzahl fällt auf irgendwie 700-800 1/min, da bin ich kurz munter geworden ^^
Nachteil noch, das Log ist halt dann ziemlich nutzlos, wenn es voll mit diesen Einträgen ist, gehen vielleicht wichtige unter, die einem sonst eher auffallen würden.
—Eddi
Born to fly ...
forced to work.
Firefly
25 June 2026 14:5025.06.2026 14:50
Quick update
I have now removed the Mini Vbar and replaced it with a Vstabi Neo.
There are no more error messages in the log.
So it seems there's something wrong with the Mini.
Kurzes Update
Ich habe jetzt mal das Mini Vbar ausgebaut und durch ein Vstabi Neo ersetzt.
Hier sind keinerlei Fehlermeldungen mehr im Log.
Scheint also was mit dem Mini zu sein.
Eddi E. aus G.
26 June 2026 09:0126.06.2026 09:01
Good morning,
That's possible. The RX A connector on the Mini was originally intended for servo outputs with standard wiring, but was later repurposed so that the Governor – which was originally a feature of the full-size model – could also be used with the Mini. However, I believe it doesn't have the same signal input amplifier as the NEO with its dedicated input. This means it works if the signal source adheres to certain standard operating procedures, or it doesn't.
A pull-up resistor might help, or a voltage divider for an external sensor if the RC voltage directly affects the signal level.
Most likely the Mini doesn't even have anything wrong with it, otherwise the signal input probably wouldn't work at all, 'it is what it is'.
But... it's good if it works :-)
—Eddi
Born to fly ...
forced to work.
Moin,
kann schon sein. Der Anschluss RX A der Mini ist ja eigentlich mal für Servoausgänge für Standard-Verkabelung vorgesehen gewesen, wurde im Zuge der Zeit umgewidmet, damit man auch mit der Mini den Governor – der ursprünglich ein Feature der Full-Size war – verwenden kann. Der hat aber meine ich eben nicht den Signal-Eingangsverstärker so wie die NEO mit dediziertem Eingang. D. h. es funktioniert, wenn der Signalgeber sich an gewissen übliche Spielregeln hält, oder halt nicht.
Ggfs. könnte ein Pull-up Widerstand helfen, oder bei ext. Sensor ein Spannungsteiler, wenn die RC-Spannung dort direkt auf den Signalpegel Einfluss hätte.
Höchstwahrscheinlich hat die Mini nicht mal was, sonst würde der Signaleingang vermutlich gar nicht funktionieren, 'es ist halt wie's ist'.
Aber ... gut wenn's tut :-)
—Eddi
Born to fly ...
forced to work.
RV
26 June 2026 17:0626.06.2026 17:06
That's right - the Mini is somewhat "limited" in that respect. The signal voltage levels probably aren't quite right.
And honestly, older stabilizers haven't been tested for 10 years. If something still works flawlessly by chance – okay, if not – that's just how it is.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
So ist es - die Mini ist da was "beschränkt". Bestimmt passen da die Spannungspegel des Signale nicht ganz.
Und ehrlich - auf Altstabis wurde auch seit 10 Jahren nicht mehr getestet. Wenn da was zufällig störungsfrei noch geht - okay, wenn nicht - isso.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.