← Cafe

Failure, then abaturz translated

Public Talk › Cafe · Started by Simon_75 on 15 July 2026 22:0815.07.2026 22:08
Simon_75 15 July 2026 22:0815.07.2026 22:08
Hello dear colleagues

Yesterday I wanted to fly a few more laps. On the third lap, I had a malfunction. I wanted to do a tail-first backflip across the ground, but at a height of about 20-30 meters, the helicopter fell like a stone.

Can you use the logs to determine what caused the crash?

07/14/2026 7:25:32 p.m.;VBar Start -- Goblin 570 -- 0027010050 -- V 8.2 -- pl 37

Flight details 14.07.2026 19:25:30

Goblin 570
0027010050
VBar Simon
11007665

I had no connection at all, and the motor switch didn't beep, indicating it had switched off in a stressful situation. Could the connection have been broken? It was in an open field.

Best regards, Simon

PS: How can I be sure that my VBar is still working correctly?

07/14/2026 7:25:32 p.m.;VBar Start -- Goblin 570 -- 0027010050 -- V 8.2 -- pl 37
14.07.2026 19:25:32 Good; Cold start
14.07.2026 19:25:33 Good;VBackup Device detected
14.07.2026 19:25:33 Good; Backup connected, cap: 7.9V
14.07.2026 19:25:33 Good; Backup minimum ready, cap: 7.9V
14.07.2026 19:25:33 Good; Reset Reason: Power On
14.07.2026 19:25:33 Good; Bank 1 loaded
14.07.2026 19:25:33 Good; Bank 2 loaded
14.07.2026 19:25:33 Warning; Initialization is being repeated...
14.07.2026 19:25:34 Warning; Initialization is being repeated...
07/14/2026 7:25:38 p.m. Good; HW controller detected
14.07.2026 19:25:38 Good; Calibration complete
14.07.2026 19:25:45 Good; Backup in standby
14.07.2026 19:25:47 Good; Manual battery selection: ManiaX 5500 6S 2
14.07.2026 19:26:32 Good;VBackup connected, cap:8.0V
14.07.2026 19:26:43 Good;VBackup in standby
14.07.2026 19:26:48 Good;VBackup connected, cap:8.0V
14.07.2026 19:26:49 Info; Speed controller switched ON
14.07.2026 19:26:49 Good; Motor switch Motor On
14.07.2026 19:29:44 Info; No signal from the speed sensor
07/14/2026 7:29:44 PM Warn; HW overcurrent
07/14/2026 7:29:47 p.m. Info;Off - Controller - Umin:20.8V Imax:109.5A Temp:55?
14.07.2026 19:29:47 Good; Bank 4 loaded
14.07.2026 19:29:47 Info; Speed controller switched to OFF
14.07.2026 19:29:48 Good; Motor switch Motor Off
14.07.2026 19:29:55 Good; VBackup in standby
14.07.2026 19:30:10 Good; Backup connected, cap: 8.0V
14.07.2026 19:30:20 Good; Backup in standby
07/14/2026 7:30:35 p.m.;VBar Logfile End -- 07/14/2026 -- 7:30:35 p.m
14.07.2026 19:30:35 Good;VBackup Consumed: 19mAh
14.07.2026 19:30:35 Good;VBackup Separated
14.07.2026 19:30:35 Good;HW Controller Separated

14.07.2026 19:29:44 Info; No signal from the speed sensor
14.07.2026 19.29.24 Warning HW Overcurrent



Edited 1 time(s). Last edit at 07/15/2026 10:15PM by Simon_75.
machine-translated from German · Show original
RV 15 July 2026 23:5815.07.2026 23:58
I just looked at it in the cloud.

Regarding the radio communication: It's working perfectly. Over the entire flight, we only lost about 30 packets – out of approximately 30,000 sent. Furthermore, the return transmission (telemetry, log) continued uninterrupted.

Regarding the log above: It's noticeable that the HW ESC reported an overcurrent at 19:29:44. However, the recorded current value was rather moderate. It wasn't much. You then "reacted" a few seconds later.

Regarding the UI log in the cloud: At 19:29:44 the current drops to 0 A. So the controller shut down at that point. The RPM also drops to 600 rpm.

Therefore, I would say that one needs to talk to HW to find out why the controller is sending an overcurrent warning and shutting down - even if the circumstances don't warrant it.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
Simon_75 16 July 2026 01:1116.07.2026 01:11
Hello Rainer

Thanks for the research. So, the hardware has shut down? Can I read the error code from the hardware?

Would you still use the controller? Could I have prevented the crash by grounding it? Did the backup still work?
At the same second, the message "no signal from the speed sensor" appears first; what does that mean?
Best regards, Simon



Edited 2 time(s). Last edit at 07/16/2026 01:35AM by Simon_75.
machine-translated from German · Show original
Eddi E. aus G. 16 July 2026 09:0316.07.2026 09:03
Good morning,

The regulator is switched off, it looks like this.

I have no idea if the hardware logs internally; at least I'm not aware of it doing so.

Still use it... 'actually' yes, if the cause is found and it's not a regulator defect.
Overcurrent _could_ be caused by a short circuit/ground fault on the motor side if the cables/insulation/connectors are not in good condition, or possibly also by mechanical damage to the cables or windings in the motor, e.g. if a screw is too long and pushes through.

It's impossible to say whether an electrostatic discharge was the cause. It's rather unusual; if it did happen, it would briefly "flash" the sensitive microelectronics, but there's no obvious indication of that in the logs.

According to the log, the backup worked and was logged.

The two messages are possibly related: the controller is "stuttering" and briefly not outputting an RPM signal (RPM cable), and it's reporting an overcurrent on the telemetry (tele-connection). It's like all the warning lights in a car suddenly coming on.

However, everything seemed to be fine again after switching it off, which again points to the controller/motor (cable) etc., since nothing happens when it no longer supplies power to the motor.

These are all just interpretations based on the data, but you can also rule some things out this way, radio, RC power supply for example.

—Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
Simon_75 17 July 2026 22:4017.07.2026 22:40
Thank you so much for the detailed answer, dear Rainer and Eddi.

About two weeks ago, I replaced my Scorpion 4025 1100kv motor with a Payro 650-103 (used, 11 flights). Connections were insulated separately and also protected with heat shrink tubing over the edges.

I've attached some hardware data; can you make use of it?

I'm going to buy a new helicopter, but unfortunately there isn't a wide selection in this size. What I'm wondering, though, is whether I can install the speed controller and/or motor in the new helicopter.

What can I do to further narrow down the error?

Thank you very much for your efforts.

Best regards, Simon



Edited 1 time(s). Last edit at 07/17/2026 11:06PM by Simon_75.

machine-translated from German · Show original
Simon_75 17 July 2026 22:4517.07.2026 22:45
P.S. This must be the event. I think the time zone is still correct on the hardware; the minute and second settings seem about right.

I only have the HW mobile app with a Bluetooth adapter; is there another way to read the data?

machine-translated from German · Show original
RV 18 July 2026 11:4918.07.2026 11:49
Quote: Is there another way to read the data?

Presumably with the PC adapter (LCD Program Box Pro) and the PC software.

Otherwise... could you rotate the posted image?

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
Eddi E. aus G. 20 July 2026 09:1820.07.2026 09:18
Good morning,

Yes, extremely difficult to read, and... seems more than 90° confusing to me... 6553.3 A peak current?
At 4% gas?
And 12.5V voltage?

Then 7,740 rpm?

If this is the data that HW works with internally, then nothing surprises me anymore ^^ (referring to another HW topic, phantasmetry...).

Previously with the Scorpion, how many (uneventful) flights were there? Can you trace that?
Because – if something occurs after a change to the system – it may be related to the change.

Then it would be conceivable to continue using the controller with the Scorpion (a duo that was known to be working until recently?), in which case the Pyro would be suspect in my eyes.
And you can also visually inspect it, or even quickly test it with an insulation tester.

—Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
Simon_75 21 July 2026 10:3321.07.2026 10:33
Hello Eddie

The Scorpion motor got very hot during the warm summer days, and I could see the magnets shift slightly (it had brilliantly handled thousands of missions over the past 20 years). That's why I got a new motor. The seller had it in a Kraken 580 and switched to a 12S battery. I called him again, and he said he hadn't had any problems in the few flights he'd done. I never had such an event in the log during any of my flights. There was a period of increased vibration, but I was able to resolve that. The hardware contains six logs, but only one shows the high current.

PS: What I find strange is that the controller was set to 3% and 600 RPM, and at that moment the voltage dropped (with a new Maniax on its second flight). Shouldn't it be the other way around under load, or am I mistaken?

I think I'll replace the motor and controller.

Thank you for your efforts.

Best regards, Simon



Edited 2 time(s). Last edit at 07/21/2026 10:56AM by Simon_75.

machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless