TRACON
26 July 2026 20:1326.07.2026 20:13
Question for the MIKADO team:
If I connect the mini receiver to the OFS of the OMP M2, can I then also control/trigger the rescue function of the OFS?
I would like to use my VBC for control.
Thanks and regards
Andreas
Frage and das MIKADO Team:
Wenn ich den Mini Empfänger mit dem OFS des OMP M2 verbinde, kann ich dann auch die Rettungsfunktion des OFS ansteuern/ auslösen?
Würde gerne meine VBC für die Steuerung nutzen.
Danke und Gruß
Andreas
thomas1130
26 July 2026 20:3326.07.2026 20:33
TRACON
26 July 2026 20:4426.07.2026 20:44
Great, thanks Thomas!
Then I'll order the receiver immediately!
Super, danke Thomas!
Dann bestelle ich mir aber sofort den Empfänger!
TRACON
1 August 2026 17:1801.08.2026 17:18
So, I have successfully connected the micro receiver to the OFS3 and all functions seem to be working.
Now to Macrocell 15 - connection to the rescue function:
I have switch option 1 selected, meaning the lower left three-way switch is now active.
(The basic setup is in Mikado setting switch option 3. I have changed this to switch option 1)
And now I need HELP! ;-)
My three-way switch is intentionally installed in a reversed position: If I want to activate rescue, I only need to briefly tap the switch downwards from the center position with my middle finger to start the rescue sequence (spring-loaded, so just tap, the switch returns to the center position 0).
What exactly do I need to configure in the setup of macro cell 15?
It currently shows CH5: 3D ATT. (I don't want ATT mode.) In OFS, I've set CH5 for rescue. In macro cell 15: Position A appears when I tap the switch downwards, so A should trigger the rescue. (-125) is then displayed. Center is 0 and position B is (125).
So the switch control works.
I'll need a little step-by-step guide for that, unfortunately :-)
How do I assign the OFS rescue as such?
Thank you so much for your help!
greeting
Andreas
Edited 1 time(s). Last edit at 08/01/2026 05:20PM by TRACON.
So, habe den Micro Empfänger erfolgreich an das OFS3 angebunden und alle Funktionen scheinen zu funktionieren.
Jetzt zur Macrocell 15 - Anbindung and die Rettungsfunktion:
Ich habe die Switchoption 1, also der linke, untere Dreiwege Schalter ist jetzt aktiv.
(Grundsetup ist in der Mikado Einstellung Switchoption 3. Diese habe ich auf Swichtoption 1 gewechselt)
Und nun benötige ich HILFE! ;-)
Mein Dreiwegeschalter ist absichtlich verdreht eingebaut: Wenn ich Rettung aktivieren möchte, muss ich den Schalter aus der Mittelstellung lediglich mit dem Mittelfinger kurz nach unten antippen, um die Rettungssequenz zu starten (Springloaded, also einfach nur antippen, Schalter kehrt in die Mittelstellung 0 zurück).
Was muss ich nun genau einstellen in dem Setup der Macrozelle 15?
Da steht ja jetzt erst einmal CH5: 3D ATT. (ATT Mode möchte ich nicht) Im OFS habe ich den CH5 für die Rettung eingestellt. In Macrozelle 15: Position A erscheint, wenn ich den Schalter nach unten antippe, also sollte A die Rettung auslösen. (-125) wird dann angezeigt. Mitte ist gleich 0 und Position B ist (125).
Schalter Ansteuerung funktioniert also.
Da benötige ich jetzt leider eine kleine Schritt für Schritt Anleitung :-)
Wie weise ich die OFS-Rettung als solche zu?
Vielen lieben Dank für die Hilfe!
Gruß
Andreas
Edited 1 time(s). Last edit at 08/01/2026 05:20PM by TRACON.
TRACON
2 August 2026 11:4502.08.2026 11:45
If I leave the Mikado preset on Switch Option 3 (3D/ATT), pressing the corresponding switch in the MC menu shows no reading. Only the switch position is displayed.
Therefore, there will probably be no active switching from 3D to ATT?
Lasse ich die Mikado Voreinstellung auf Switch Option 3 (3D/ATT) zeigt bei Betätigung des entsprechenden Switches in dem MC Menü kein Ausschlag an. Lediglich die Switch Position wird angezeigt.
Somit wird es wahrscheinlich auch kein aktives Umschalten von 3D auf ATT geben?
Aaronheli
2 August 2026 18:5902.08.2026 18:59
Hello Andreas,
Depending on what you have set in the OFS3 app, either Attitude OR rescue mode will be activated via macro cell 15.
The app also describes this as follows: Attitude Mode is replaced by Rescue Mode. :-)
In macro cell 15, you simply select your switch (in your case Sw Op 1) and set the output signal to 100 in the desired switch position (top/middle/bottom), where the rescue mode should be active.
You can easily test it with the helicopter switched on to see if it works. The swashplate will briefly give a positive pitch when the rescue mode is triggered.
Greetings Aaron
Hallo Andreas,
je nachdem was du in der OFS3 App eingestellt hast, wird über die Makrozelle 15 der Attitude ODER der Rettungsmodus aktiviert.
Das ist in der App auch so beschrieben, dass der Attitude Modus durch den Rettungsmodus ersetzt wird. :-)
In der Makrozelle 15 wählst du also einfach deinen Schalter (in deinem Fall Sw Op 1) und stellst das Ausgangssignal in der gewünschten Schalterstellung (oben/mitte/unten) auf 100, wo der Rettungsmodus aktiv sein soll.
Du kannst es ja einfach mit eingeschaltetem Heli testen, ob es passt. Die Taumelscheibe gibt bei ausgelöstem Rettungsmodus kurz positiv Pitch.
Grüße Aaron
TRACON
3 August 2026 10:2103.08.2026 10:21
Thanks Aaron, it works as described. :-)
I initially didn't notice any response from Pitch. After reinstalling it, it worked.
greeting
Andreas
Danke Aaron, funktioniert wie beschrieben. :-)
Ich hatte erst keine Reaktion auf Pitch feststellen können. Nach Neuinstallation hat es funktioniert.
Gruß
Andreas