Zille1987
3 May 2026 16:1903.05.2026 16:19
Hello Team Mikado,
I pre-ordered the Stratos 200 from XL Power and also a Vstabi Evo in a neon yellow aluminum case.
Then it suddenly occurred to me that it's not a rear servo but a rear motor that's being controlled.
How is this "selected" or implemented in Vstabi Evo? Is there a setting for it, or do macrocells need to be written? I haven't encountered this situation before.
VG
Zille
Edited 1 time(s). Last edit at 05/03/2026 04:20PM by Zille1987.
Hallo Team Mikado,
habe mir den Stratos 200 von XL Power vorbestellt und gleich dazu ein Vstabi Evo im neongelben Alu-Case.
Jetzt kam mir plötzlich der Gedanke, dass da ja kein Heckservo sondern ein Heckmotor angesteuert wird.
Wie wird das im Vstabi Evo "ausgewählt" bzw. realisiert? Gibts da eine Einstellung zu oder müssen dafür Makrozellen geschrieben werden? Habe den Fall bisher nicht gehabt.
VG
Zille
Edited 1 time(s). Last edit at 05/03/2026 04:20PM by Zille1987.
thomas1130
3 May 2026 16:2103.05.2026 16:21
That's no problem - there's a "setting" for that...
LG
Ist kein Problem - da gibt es eine "Einstellung" dafür...
LG
Zille1987
9 May 2026 14:1609.05.2026 14:16
Hello everyone,
Unfortunately, I have to bring this topic up again.
Yesterday I wanted to put the Stratos 200 into operation and first created a new model as "No Mikado Helicopter". Then I went through the entire setup (servos set to center pulse and 200 Hz, etc.) and then, at the "tail rotor" point, switched from servo to motor by holding down the button for a long time.
Unfortunately, the tail motor only beeps and twitches – so there's clearly some kind of fault. If I lower the DShot protocol from DShot600 to 300 or even further, the beeping slows down, but the motor still doesn't start. The main motor, on the other hand, works perfectly.
I then created a new test setup with "Logo Helicopter" -> "Logo 200" and adjusted the servo settings accordingly. While this eliminated the problem with the beeping and jerking of the tail motor, the helicopter initially flew terribly.
In the afternoon I went briefly into the field and made a total of five familiarization flights.
Initial situation with the settings of the Logo 200:
The main rotor experiences problems with strong pitching impulses, even while hovering. The tail section then oscillates up and down at a high frequency.
Tail rotor practically non-existent: strong oscillation while hovering, no clean locking into place. With positive pitch inputs, the tail rotates up to 120°, and with negative pitch inputs, it rotates in the opposite direction.
During cautiously tested tick-tock maneuvers, the helicopter rotates completely around its own axis under load shocks. Clean tail stops while hovering are practically impossible.
Result after five test flights:
By reducing the main rotor gain, I was able to eliminate the tail bouncing during pitching maneuvers.
The tail section itself is still not really under control. While I was able to improve it somewhat with pitch pre-compensation and torque compensation, 3D flying is currently out of the question.
To make sure I hadn't gotten a "Monday heli," I then quickly installed a Nexus-XR with a Radiomaster Pocket (ELRS) and set up Rotorflight with a few basic adjustments. This immediately made the tail stand rock-solid – completely unobtrusive and without any problems.
Therefore, I'm now fairly certain it's purely a settings issue. However, I do find it strange that the manual setup with "No Mikado Heli" was practically unusable.
Therefore, my question is:
What am I doing wrong here, or what am I perhaps overlooking? I would really like to fly the Stratos with the EVO instead of the Nexus.
Thank you in advance for any helpful tips and experiences!
Edited 1 time(s). Last edit at 05/09/2026 02:17PM by Zille1987.
Hallo zusammen,
ich muss das Thema leider noch einmal aufgreifen.
Ich wollte gestern den Stratos 200 in Betrieb nehmen und habe zunächst ein neues Modell als „Kein Mikado Helikopter“ angelegt. Danach habe ich das Setup komplett durchlaufen (Servos auf Mittenimpuls und 200 Hz eingestellt etc.) und anschließend beim Punkt „Heckrotor“ per langem Gedrückthalten von Servo auf Motor umgestellt.
Leider piept und zuckt der Heckmotor dabei nur – hier scheint also eindeutig irgendein Fehler vorzuliegen. Wenn ich das DShot-Protokoll von DShot600 auf 300 oder noch weiter herunterstelle, wird das Piepsen zwar langsamer, der Motor dreht aber trotzdem nicht an. Der Hauptmotor funktioniert dagegen ohne Probleme.
Daraufhin habe ich testweise ein neues Setup mit „Logo Helikopter“ -> „Logo 200“ erstellt und die Servoeinstellungen entsprechend angepasst. Damit ist das Problem mit dem Piepen und Zucken des Heckmotors zwar verschwunden, allerdings flog der Heli zunächst wie ein Sack Nüsse.
Nachmittags war ich dann kurz im Felde und habe insgesamt fünf Einstellflüge gemacht.
Ausgangssituation mit den Einstellungen des Logo 200:
Hauptrotor macht Probleme bei stärkeren Nick-Impulsen bereits im Schweben. Dabei schlägt das Heck hochfrequent auf und ab.
Heckrotor praktisch nicht vorhanden: starkes Pendeln im Schweben, kein sauberes Einrasten. Bei positiven Pitchstößen dreht das Heck teilweise bis zu 120° weg, bei negativen Pitchstößen entsprechend in die andere Richtung.
Bei vorsichtig angetesteten Tick-Tocks dreht sich der Heli bei Laststößen komplett um die eigene Achse. Saubere Heckstops im Schweben praktisch nicht möglich.
Ergebnis nach fünf Einstellflügen:
Durch Reduzierung des Hauptrotor-Gains konnte ich das Auf- und Abschlagen des Heckes bei Nickstößen beseitigen.
Das Heck selbst ist aber weiterhin nicht wirklich unter Kontrolle. Mit Nick-Prekompensation und Drehmomentausgleich konnte ich es zwar etwas verbessern, an 3D-Flug ist aktuell aber nicht zu denken.
Um sicherzugehen, dass ich keinen „Montagsheli“ erwischt habe, habe ich anschließend kurz ein Nexus-XR mit Radiomaster Pocket (ELRS) verbaut und Rotorflight mit wenigen Grundeinstellungen flugbereit gemacht. Damit stand das Heck sofort wie angenagelt – absolut unauffällig und problemlos.
Deshalb bin ich inzwischen ziemlich sicher, dass es sich um ein reines Einstellungsproblem handelt. Allerdings finde ich es schon merkwürdig, dass das manuelle Setup mit „Kein Mikado Heli“ praktisch überhaupt nicht betriebsbereit war.
Daher meine Frage:
Was mache ich hier falsch bzw. übersehe ich eventuell? Ich würde den Stratos wirklich gern mit dem EVO statt mit dem Nexus fliegen.
Vielen Dank schon einmal für hilfreiche Hinweise und Erfahrungen!
Edited 1 time(s). Last edit at 05/09/2026 02:17PM by Zille1987.
RV
9 May 2026 14:5509.05.2026 14:55
You're probably not doing anything wrong; the problem lies deeper.
HW built a controller with firmware that has some quirks. We disclosed this as soon as we knew about it (and unfortunately, they don't ask us at the beginning...). It's almost always the same story: there's a collaboration, we get it too late for testing and feedback, and then this is how it turns out.
Doesn't XL have a preset "in stock" that works?
Therefore - please address to XL and HW.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Edited 1 time(s). Last edit at 05/09/2026 03:24PM by RV.
Du machst vermutlich nichts falsch, das Problem sitzt tiefer.
HW hat einen Regler mit einer Firmware gebaut welche hier so ihre Macken hat. Wir haben das sowie es uns bekannt war (und uns fragt man leider nicht am Anfang ...) kundgetan. Es ist einfach fast immer dasselbe, da gibts ne Kooperation, wir bekommens zu spät zum Testen und Feedback und dann kommt es so raus.
Hat XL nicht ein Preset "auf Lager" das funktioniert?
Insofern - bitte an XL und HW Adressieren.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Edited 1 time(s). Last edit at 05/09/2026 03:24PM by RV.
Zille1987
9 May 2026 17:2909.05.2026 17:29
Hello Rainer,
thanks for the quick reply.
Even though Mikado doesn't seem to be directly "at fault" here, I, as an end customer, would like to describe my perspective:
I deliberately chose a Mikado FBL system, which in my configuration costs a total of €379 (Pro & Rescue upgrade, Yellow version). Other FBL systems cost only a fraction of that – in my case, the FBL system even exceeds the value of the rest of the helicopter.
Therefore, I honestly expect the system to function reliably. Unfortunately, that is currently not the case.
When I then receive feedback that I should contact XL Power or HobbyWing, I find that quite incomprehensible.
Therefore, my specific question is:
Are you actively working on this issue and will there be an update? If so, what is the approximate timeframe for this?
Hallo Rainer,
danke für die schnelle Antwort.
Auch wenn Mikado hier scheinbar nicht direkt „schuld“ an der Sache ist, möchte ich als Endkunde einmal meine Sicht schildern:
Ich entscheide mich ganz bewusst für ein FBL-System von Mikado, das in meiner Konfiguration insgesamt 379 € kostet (Pro- & Rescue-Upgrade, Yellow-Version). Andere FBL-Systeme kosten nur einen Bruchteil davon – in meinem Fall übersteigt das FBL sogar den Wert des restlichen Helis.
Daher erwarte ich ehrlich gesagt, dass das System zuverlässig funktioniert. Genau das ist aktuell aber leider nicht der Fall.
Wenn ich dann als Rückmeldung erhalte, ich solle mich an XL Power oder HobbyWing wenden, sorgt das bei mir schon für Unverständnis.
Deshalb meine konkrete Frage:
Wird das Thema von euch aktiv bearbeitet und ein Update kommen? Falls ja, welchen zeitlichen Horizont könnt ihr hierfür ungefähr nennen?
RV
9 May 2026 19:2509.05.2026 19:25
Well, we're in contact with Hobbywing. We're also working in parallel to see if we can achieve anything on our end. Alex and Uli are working hard on this, and Carl is helping out wherever he can.
I can't say more about it, I'm not directly involved.
If XL had shown up earlier with the part and given us some time... then it might all be over by now. But we only got involved after sales had already started; to be precise, that became clear on April 29th.
Incidentally... if you install an OMP controller from the Logo 200, everything is fine - tests were also carried out with this to make sure that the problem was with the controller.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Edited 1 time(s). Last edit at 05/09/2026 07:34PM by RV.
Naja - wir sind mit Hobbywing in Kontakt. Desweiteren arbeiten wir auch parallel daran ggf. auf unserer Seite ev. was zu erreichen. Das Ganze machen Alex und Uli mit Hochdruck, Carl unterstützt wo er kann.
Mehr kann ich dazu nicht sagen, ich bin da nicht direkt involviert.
Wäre XL eher mit dem Teil bei uns ums Eck gekommen und hätte uns was Zeit gelassen ... dann wäre das möglicherweise schon ausgestanden. Aber wir kamen erst ins Boot als der Verkauf schon losging, genau gesagt am 29. April hat sich das herausgestellt.
Übrigens ... pflanzt man einen OMP Regler aus dem Logo 200 ein ist alles gut - damit wurden ebenso Tests gemacht um sicher zu sein dass es am Regler liegt.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Edited 1 time(s). Last edit at 05/09/2026 07:34PM by RV.
Zille1987
10 May 2026 10:4810.05.2026 10:48
Hello Rainer,
First of all, thank you very much for responding to my request and being available over the weekend.
Last night I saw a video on Facebook from Carl-Henning Siebert showing that you're already actively working on the problem and apparently have a solution in sight. It seems only the final touches are needed before it's released to customers.
Here is the link to the video:
Facebook video by Carl-Henning Siebert To be honest, this information would have defused my dissatisfaction much earlier, or even prevented it from escalating to such an extent in the first place. Transparent communication is simply enormously helpful in such situations and shows that the issue is being taken seriously.
Greetings from North Rhine-Westphalia!
Zille
Hallo Rainer,
zunächst einmal vielen Dank, dass du am Wochenende auf meine Anfrage reagierst und erreichbar bist.
Ich habe gestern Abend auf Facebook noch ein Video von Carl-Henning Siebert gesehen, das zeigt, dass ihr bereits aktiv an dem Problem arbeitet und offenbar auch schon eine Lösung in Aussicht habt. Scheinbar fehlt aktuell nur noch der Feinschliff, bevor das Ganze bei den Kunden ankommt.
Anbei der Link zum Video:
Facebook-Video von Carl-Henning Siebert
Diese Informationen hätten meine Unzufriedenheit ehrlich gesagt deutlich früher entschärft bzw. gar nicht erst so hochkochen lassen. Transparente Kommunikation hilft in solchen Situationen einfach enorm und zeigt, dass das Thema ernst genommen wird.
Gruß aus NRW
Zille
Eddi E. aus G.
11 May 2026 09:1411.05.2026 09:14
Hi,
In our opinion, XL should actually be obligated to provide information and offer a solution.
Carl is also involved, fighting :-)
It would have been even better to come around the corner earlier, so that any potential inconsistencies could be uncovered and resolved before they reached the customer.
And when you (their team pilot and we in this case) give qualified feedback, you should accept and review it, not stonewall first.
All of this takes time.
Otherwise... everyone would be happy.
A workaround is in the works, but it would be better if the cause could be eliminated in parallel, which would mean an update of the controllers that have already been produced and delivered.
It would be even better if this could have been noticed before production, so
Now that workarounds are on the horizon, I almost don't believe it anymore, as it suggests that the problem lay elsewhere, which has been proven in both image and sound to be simply not true.
There's so much more performance potential to be squeezed out... for the customer, that would probably mean with V2...
Grüßle
Eddi
Born to fly ...
forced to work.
Hi,
eigentlich wäre unseres Erachtens XL in der Pflicht, zu informieren und die Lösung in Aussicht zu stellen.
Carl ist da ja auch dran, kämpft :-)
Noch besser wäre gewesen, früher um's Eck zu kommen, so dass man mögliche Ungereimtheiten aufdecken und ausräumen kann, bevor sie zum Kunden durchschlagen.
Und wenn man (deren Team-Pilot und wir in dem Fall) qualifiziertes Feedback geben, das auch annehmen und überprüfen, nicht erst mal mauern.
Das kostet alles Zeit.
Anders ... wären alle glücklich.
Ein Workaround ist in der Mache, aber besser wäre, wenn die Ursache parallel abgestellt würde, was aber ein Update der bereits produzierten und ausgelieferten Regler bedeuten würde.
Noch besser wäre, wenn das vor der Produktion hätte aufgefallen sein können, s.o.
Jetzt, wo Workarounds vor der Tür stehen, glaube ich da aber fast nicht (mehr) dran, das suggeriert ja, dass das Problem doch anderswo lag, was aber nachgewiesen in Bild und Ton schlicht und einfach nicht stimmt.
Man könnte noch so viel mehr an Performance rauskitzeln ... für den Kunden bedeutet das dann vermutlich, bei V2 ...
Grüßle
Eddi
Born to fly ...
forced to work.
steveman
13 October 2026 20:2713.10.2026 20:27
Has there been any change with the Stratos 200?
I'd really like it, but only if it works well with VBar. Best regards, Stefan
Hat sich da was getan beim stratos 200?
Würd mir sehr gut gefallen aber nur wenn er mit vbar gut funktioniert. Lg Stefan
RV
13 October 2026 20:3313.10.2026 20:33
https://www.vstabi.info/forum/list.php?68 Is there a dedicated forum for this, moderated by Carl-Henning Siebert? ;-)
Maybe you'll find something there, otherwise we'll have to wait until Carl gets in touch.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Edited 1 time(s). Last edit at 10/13/2026 08:34PM by RV.
https://www.vstabi.info/forum/list.php?68
Gibts ein eigenes Forum welches von Carl-Henning Siebert betreut wird dazu ;-)
Vielleicht findest Du dort was, ansonsten müssen wir warten bis sich Carl vielleicht mal meldet.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Edited 1 time(s). Last edit at 10/13/2026 08:34PM by RV.
thomas1130
14 October 2026 05:0614.10.2026 05:06
steveman Wrote:
-------------------------------------------------------
Has there been any change with the Stratos 200?
I would really like that, but only if he's with
> vbar works well. Best regards, Stefan
The Stratos 200 works excellently with VBAR - both 2 and 3 blades :-)
I've already done many flights on the mechanics - it works fantastically - it's extremely fun.
LG
steveman Wrote:
-------------------------------------------------------
> Hat sich da was getan beim stratos 200?
> Würd mir sehr gut gefallen aber nur wenn er mit
> vbar gut funktioniert. Lg Stefan
Der Stratos 200 funktioniert ausgezeichnet mit VBAR - sowohl 2 als auch 3 Blatt :-)
Hab schon sehr viele Flüge auf den Mechaniken - geht traumhaft - macht extrem viel Spaß.
LG