Volker Wahlen
14 March 2025 08:3514.03.2025 08:35
Hello, I've recently taken up flying fixed-wing aircraft.
So far, "everything" is set up.
I managed to get the yaw trim right, both directions are even correct.
Now I wanted to do the same with the elevator.
I can only get that in one direction; in the other direction, the correction is inverted.
When flying a right or left turn, upward corrections are always necessary.
Which parameter do I need to adjust for it to work correctly?
Greetings from sunny Thailand
Volker
Hallo, Bin mal unter die Flächenflieger gegangen,.
Soweit "alles" eingestellt.
Trim für Yaw habe ich hinbekommen, beide Richtungen stimmen sogar.
Nun wollte ich das gleiche mit dem Höhen ruder machen.
Das bekomme ich nur in einer Richtung in, in der anderen Richtung ist die Korrektur inverted.
Beim Kurvenflug rechts oder links muss ja immer nach oben korrigiert werden.
Welchen Parameter muss ich anpacken damit es richtig greift?
Gruesse aus dem sonnigem Thailand
Volker
Eddi E. aus G.
14 March 2025 09:2014.03.2025 09:20
Good morning,
If I understand correctly, the way it is is correct for now: the trim changes the center (trim the control surface into the profile, or for certain flight conditions, trim against the center of gravity/pressure point or against a warped model).
That means if I trim by 'pulling', virtually the entire servo travel is reversed.
One could now mix in the height/crosswise function in the setup, but this only works as a percentage, so it works in one direction against the other.
Alternatively, one can take the macrocell CH1 (height), make it a mixer, and use as inputs CH1 (what would normally be output to CH1) and MC30 (any unused cell).
Then, cell 30, type curve, input FC Roll, and swirl a V-curve.
You can either leave the mixing ratios in cell CH1 at 100/100 and flatten the curve accordingly (fly it, 6 values to touch), or you create the V-curve in cell 30 +100...0...+100, and adjust it with the mixing ratio in CH1 (only one value to touch).
Or... you can simply pull back gently on the stick when flying a turn ^^ the mixing would potentially always turn rolls in straight flight into barrel rolls or other crippled results.
Grüßle
Eddi
Born to fly ...
forced to work.
Moin,
wenn ich das richtig verstehe, ist es so wie es ist erst mal richtig: die Trimmung verändert ja die Mitte (Steuerfläche in's Profil trimmen, oder für bestimmte Flugzustände, gegen den Schwerpunkt/Druckpunkt oder gegen ein verzogenes Modell trimmen).
D. h. wenn ich 'ziehen' trimme, wird quasi der ganze Servoweg verdreht.
Man könnte jetzt im Setup der Funktion Höhe Quer beimischen, das geht aber nur einfach prozentual, läuft also in eine Richtung dagegen.
Oder man nimmt die Makrozelle CH1 (Höhe), macht die zu einem Mischer, und nimmt als Eingänge einmal CH1 (das was normal an CH1 ausgegeben würde) sowie MC30 (eine beliebige noch ungenutzten Zelle).
Dann, Zelle 30, Typ Kurve, Eingang FC Roll, und eine V-Kurve hinzwirbeln.
Man kann nun entweder in Zelle CH1 die Mischanteile 100/100 lassen und die Kurve entsprechend flach stellen (erfliegen, 6 Werte zum Anfassen), oder man macht die V-Kurve in Zelle 30 +100...0...+100, und zieht sie mit dem Mischanteil in CH1 hin (nur ein Wert zum anfassen).
Oder ... man zieht einfach behutsam am Knüppel Höhe, wenn man eine Kurve fliegt ^^ die Beimischung würde aus Rollen im Geradeausflug u. U. immer Fassrollen oder andere krüppelige Ergebnisse machen.
Grüßle
Eddi
Born to fly ...
forced to work.
Volker Wahlen
14 March 2025 09:5614.03.2025 09:56
:-) Yes, I'll do the latter first :-)
The first one sounds very exciting. Let's see where it ends up.
I'm completely lost with the first paragraph. I stopped reading at the high school diploma level :-)
It's the end of the world here anyway. So I can still tinker with something.
Greetings from sunny Thailand
Volker
:-) Ja werde dann erstmal letzteres tun :-)
Das erste kling sehr spannend. Mal schaun wo ich da Ende.
Mit dem ersten Absatz komme ich gar nicht klar. Hatte bei Oberschulreife aufgehört :-)
Jetzt ist hier eh Weltuntergang angesagt. Da kann ich noch was fummeln.
Gruesse aus dem sonnigem Thailand
Volker