← VPlane / VBasic VLink

Macro use with side effects translated

VBar › VPlane / VBasic VLink · Started by Volker Wahlen on 25 March 2025 12:0625.03.2025 12:06
Volker Wahlen 25 March 2025 12:0625.03.2025 12:06
I have a question.
If I use the macro function "Curve", will the mixers no longer work, e.g., aileron/rudder?
Does the sensitivity for attitude stability only work for the ailerons but not for the elevator and rudder?
Are the original Expo values also switched off then?
Bank switching is also obsolete.

Greetings from sunny Thailand

Volker



Edited once. Last edited on March 25, 2025 at 12:07 PM by Volker Wahlen. File attachments:
Open | Download - 11006398_vplane_Adiction_Neu.zip (618 bytes)
Open | Download - 11006398_macro_Adiction_Neum.zip (305 bytes)
machine-translated from German · Show original
Eddi E. aus G. 25 March 2025 13:1625.03.2025 13:16
Good morning,

If the _input_ is the original output on the connection, then yes. For example, servo on CH2 <- curve <- input CH2.

The problem is (there's always something...) if I flatten the curve very much, _all_ outputs are reduced there, including stabilization, including mixing, proportionally as if the smaller spike would occur.

Is the thing normally unflyable with maximum expo, or are you just doing that to please the Futaba fans? :-) ;-)

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
Volker Wahlen 26 March 2025 03:3426.03.2025 03:34
The plane has "huge" control surfaces and is very light.
This makes it very sensitive, especially during landing.
It's some kind of aerobatic thing.
So they set full paths, but made them more sensitive by using much more exposure.
Here with Vbar, even at 100 Expo, the dimming isn't as drastic as with Futaba. You know the curves, right?

I am also a Futaba disciple, but I want to get to know and understand your system much better and show them that it is possible.

I had hoped and thought that these macros would only affect the sticks, the selected input signal, and not the sum output.
It seems to be different when rolling; it's still okay then.

As the "commissioning manager," I would have had my programmers do it that way.
Otherwise I would have selected other inputs, but there aren't any that would need to be addressed.

Greetings from sunny Thailand

Volker
machine-translated from German · Show original
Eddi E. aus G. 26 March 2025 09:0426.03.2025 09:04
Hi Volker,

Well, one could also mix stick and stabilization (FC) together, then curve them, or curve them individually before mixing, then output them and see if you get the desired result.

But when it comes to sensitivity/twitchiness, especially in slow flight and during landing, I would try it without macro cells and with one bank dedicated to that, turning down agility (flattening the entire turn, like dual rate), and possibly also increasing stabilization (sensitivity). Set the second bank to medium, and the third bank to extreme.

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
Dirtygeri 26 March 2025 09:2326.03.2025 09:23
Hi Volker!

Eddi beat me to it... I fly several "3D monsters" (elevator with 50 to 70 degrees of deflection) without any problems using my Vbar Control, exactly as Eddi described... Bank 3 with agility of 100 (torques, flat spins, etc.), Bank 2 with agility (depending on the model - it's individual) of 40 to 70 for "nice" flying, and Bank 1 (instructor/student, possibly landing) with agility between 30 and 50...
Works perfectly! Give it a try...
Best regards, Geri
machine-translated from German · Show original
Volker Wahlen 27 March 2025 02:5227.03.2025 02:52
Sounds good. I had 30, 50, 70 maneuverability yesterday and 100 expo.
Our retired Dreamliner was happy with it yesterday, even in strong crosswinds.
The plane remained perfectly still with stabilization support and flew super straight even inverted.
He didn't notice anything.
I hadn't enabled macros, so it worked after all :-)
Thank you so much for your help.

Greetings from sunny Thailand

Volker
machine-translated from German · Show original
Eddi E. aus G. 27 March 2025 09:1327.03.2025 09:13
:-)

...following the motto, "can't be done" doesn't exist; either it's more difficult, or (in this case) done differently :-)

The beauty of our stabilization is that you don't feel like you have to work against it, but can always freely control the model.
Otherwise, torn figures, causing a flow separation in figures or 3D would hardly be possible.

—Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless