← VPlane / VBasic VLink

RX-Only 9-channel receiver, Aux3/Ch6 without servo function translated

VBar › VPlane / VBasic VLink · Started by gerdf01 on 9 April 2025 20:5809.04.2025 20:58
gerdf01 9 April 2025 20:5809.04.2025 20:58
Hello everyone,

For testing purposes, I have a setup with a VBar-RX-Only 9-channel receiver and 9 servos.
The goal of the construction: a glider with a 6-flap wing, elevator, rudder, and motor.
A new standard aircraft has been created. Macrocells have been reset.

Problem:
Aux3/Ch6 for the right landing flap is not outputting anything. The servo is unpowered.
I somehow "activated" Extender_Bus. As far as I know, RX-Only can't use Extender_Bus, right?
Under Macrocells > Settings, Extender_Bus is set to <Active>.
Deactivation with selection of <Aux2/Aux3> to use the connection as CH6 will be set to <Active> after restart.

The RX has the serial number: 27000357
I have the VBar-Control-Classic and EVO+ available.

Thank you.
Gerd
machine-translated from German · Show original
RV 9 April 2025 21:2709.04.2025 21:27
What happens when you create a new setup?

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
gerdf01 9 April 2025 21:3609.04.2025 21:36
Hello Rainer,
As always, very quickly! :-)

I already created a new standard aircraft. No effect.

Thank you all
Gerd
machine-translated from German · Show original
gerdf01 11 April 2025 16:2411.04.2025 16:24
Hello everyone.

After redoing several setups with the VBC-Classic and -EVO+, the problem persisted.
The macrocells could not be reset with the VBC-EVO+ either. It didn't complete the process. This only worked with the VBC-Classic.
I am now using a VBAR-EVO with VPlan in which I want to recreate the macro cells, as some things are no longer needed.
To observe, I put the "RX-Only-9-Channel Receiver" system with the VBC-Classic back into operation and took another look at the AUX3.
The extender bus now displays "Aux2/Aux3" and not "active," so the servo is running. It seems the sleep did us both good.
Good, the VBAR-EVO with VPlan gets its chance!

Thank you all
Gerd
machine-translated from German · Show original
RV 12 April 2025 10:1712.04.2025 10:17
Quote: The macrocells could not be reset with the VBC-EVO+ either. The procedure did not complete.

Is the system up to date? I made some changes there in the last few days.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
gerdf01 13 April 2025 18:0313.04.2025 18:03
Hello Reiner,

I just ran it again in the same version. Macro cells are now also resettable.

Thank you all
Gerd
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless