Orpheus
24 June 2025 18:4124.06.2025 18:41
Hey guys,
I need some advice and a little help.
I have been flying helicopters with VBar EVO for a long time now, and now I would like to fly and program a fixed-wing aircraft with VBar for the first time.
Since I am tired of constantly having to carry and program two different remote controls, I would now like to convert my glider (hotliner).
Now my question, since I have absolutely no experience with VPlane.
Which receiver/VBar/RX Only would be optimal?
A VBar NEO/EVO, a VBasic, or is a 7-channel RX Only receiver sufficient?
What makes the most sense?
The remote control is a VBar Control EVO
Segler is a hotliner with the following features
Engine, ailerons and elevator (T-tail)
No rudder, no flaps, and no camber-changing flaps.
Ideally, the ailerons would also have differential control, allowing them to be deployed for deceleration and landing while simultaneously mixing in elevator input. This will likely only be achievable with macrocells.
Thank you for your support
Dietmar
Hallo Jungs,
ich bräuchte einen Rat und ein wenig Hilfe.
Ich fliege nun schon lange Hubschrauber mit V-Stabi EVO, nun ist es so dass ich zum ersten Mal ein Flächenflugzeug mit der VBar fliegen und programmieren möchte.
Da ich es leid bin ständig zwei unterschiedliche Fernsteuerungen mitzunehmen und zu programmieren möchte ich nun meinen Segler (Hotliner) umrüsten.
Nun meine Frage da ich mit VPlane noch keinerlei Erfahrung habe.
Welcher Empfänger/VStabi/RX Only wäre optimal. ?
Ein VStabi NEO/EVO , eine VBasic oder genügt ein 7Kanal RX Only Empfänger ?
Was macht am meisten Sinn?
Fernsteuerung ist eine VBar Control EVO
Segler ist ein Hotliner mit folgenden Funktionen
Motor , Querruder und Höhenruder (T-Leitwerk)
Kein Seitenruder, keine Klappen und keine Wölbklappen.
Wunsch wäre auch bei den Querrudern eine Differenzierung und die Querruder zum Verlangsamen und Landen aufzustellen und Höhenruder beizumischen. Dies wird wahrscheinlich nur mit Makrozellen durchzuführen sein.
Danke für eure Unterstützung
Dietmar
Eddi E. aus G.
25 June 2025 10:0025.06.2025 10:00
Good morning,
Which stabilizer?
. if no stabilization is desired or required:
...RX Only with the appropriate number of servo connections (9/7, the 6-channel version has different connector sockets, so it's probably less suitable)
.. VBasic _if_ you want to keep the option open to upgrade to Pro or Pro+Rescue later.
...when stabilization is desired or required:
...VBar EVO VLink with Pro update, which adds VPlane.
Besides stabilization, VPlane has a few more basic setups from which you can individually adjust your model.
RX Only and VBasic work the same way.
Even without macro cells, you can assign different functions to the control surfaces depending on the bank; for example, flap function -> ailerons for landing, and flap function -> elevator. Differential is included and adjustable, as is a delay for the flap function.
No problem at all :-)
—Eddi
Born to fly ...
forced to work.
Edited once. Last edited on June 25, 2025 at 10:01 AM by Eddi E. from G.
Moin,
Welche Stabi?
. wenn keine Stabilisierung gewünscht oder benötigt wird:
.. RX Only mit passender Anzahl Servoanschlüsse (9/7, der 6-er hat andere Stecker-Buchsen, kommt vermutlich eher weniger in Frage)
.. VBasic _wenn_ man sich die Option offen halten möchte, später auf Pro oder Pro+Rettung upzudaten
. wenn Stabilisierung gewünscht oder benötigt wird:
.. VStabi EVO VLink mit Pro-Update, da kommt VPlane hinzu
VPlane hat neben der Stabilisierung noch ein paar mehr Grundsetups, von denen aus man sein Modell individuell einstellen kann.
RX Only bzw. VBasic funktionieren aber genauso.
Man kann auch ohne Makrozellen den Steuerflächen auch bankabhängig eine jeweils andere Funktion beimischen, für die Landung bspw. die Klappenfunktion -> Querruder, und Klappenfunktion -> Höhenruder. Differenzierung ist drin, einstellbar, und eine Verzögerung für die Klappenfunktion ebenso, ebenso.
Ois koa Probleem :-)
—Eddi
Born to fly ...
forced to work.
1 mal bearbeitet. Zuletzt am 25.06.2025 10:01 von Eddi E. aus G..
Orpheus
25 June 2025 15:2825.06.2025 15:28
Greetings Eddi,
So basically, I can use them all.
But if I want to program special functions like landing flaps, spoilers, and differential, is that only possible with VPlane and requires a VBar NEO/EVO with Pro version, if I understand you correctly?
With an RX Only receiver, I have all servo functions and motor (throttle) but no mixing functions, which I would need. Is that correct?
So, without the PRO version there's no VPlane and also no way to program my functions!?
Do I only need the PRO version, or do I also need the PRO+ Rescue version?
Or could the "only" PRO version also include stabilization? (I know this question sounds a bit naive :-) )
Best regards, Dietmar
Grüßle Eddi,
also grundsätzlich kann ich alle verwenden.
Aber wenn ich so spezielle Funktionen wie Landeklappen, Spoiler, Differenzierung programmieren möchte geht das dann nur mit VPlane und setzt ein VStabi NEO/EVO mit Pro Version voraus, wenn ich dich da richtig verstanden habe.
Bei einem RX Only habe ich zwar alle Servofunktionen und Motor (Gas) aber keine Mischer Funktionen die ich aber dazu bräuchte, korrekt so ?
Sprich ohne PRO Version gibt’s kein VPlane und auch die Möglichkeit meine Funktionen zu programmieren !?
Brauche ich dann nur die PRO Version oder doch auch die PRO+Rettung ?
Bzw. könnte die „nur“ PRO dann auch die Stabilisierung? ( Weiß schon kommt jetzt ein bisschen laienhaft rüber die Frage :-) )
Beste Grüße Dietmar
Eddi E. aus G.
25 June 2025 15:3425.06.2025 15:34
Good morning,
No. VBasic (upgradeable) and RX-Only (VBasic without an upgrade option; they will always remain receiver-only) have the same surface mixer as VPlane. Control surfaces are selected and configured there, including mixers.
Macro cells are included on top, both in VBasic and RX-Only.
Everything's included. Really, really.
Pro includes VPlane (with stabilization, surface gyroscope).
If you want to take a look, just take any VBar NEO or EVO, save your setup (Model Setup/Tools), then select VBasic on vstabi.info, update via VBar Control, and have a look around. That's how VBasic works in RX-Only mode.
Then select the previous firmware again, load it, reload the setup, and everything will be back to normal.
When servos and controller are connected, make sure that nothing can start mechanically (disconnect linkages if necessary) or that the drive cannot start (remove blades or unplug controller, use receiver battery).
It's better to do this with a loose stabilizer bar and a few servos on the workbench.
Grüßle
Eddi
Born to fly ...
forced to work.
2 mal bearbeitet. Zuletzt am 25.06.2025 15:34 von Eddi E. aus G..
Moin,
nein. VBasic (upgradefähig) und RX-Only (VBasic aber ohne Upgrade-Option, die werden für immer reine Empfänger bleiben) haben den selben Flächenmischer wie VPlane. Dort werden auch die Steuerflächen ausgewählt und eingestellt, inklusive Mischern.
Makrozellen gibt's on top, bei VBasic wie bei RX-Only.
Alles drin. Wirklich-wirklich.
Pro beinhaltet VPlane (mit Stabilisierung, Flächenkreisel).
Wenn Du mal schauen willst, nimm doch eine beliebige VStabi NEO oder EVO, sichere Dein Setup (Modell Setup/Werkzeuge), wähle dann auf vstabi.info VBasic, update über VBar Control, und schaue eben, probiere mal rum. So ist auch VBasic und RX-Only.
Dann die vorherige Firmware wieder auswählen, laden, das Setup zurück laden, und alles ist wieder wie vorher.
Achte nur bei angeschlossenen Servos und angeschlossenem Regler drauf, dass nix mechanisch anlaufen kann (Gestänge ggfs. aushängen) bzw. dass der Antrieb nicht anlaufen kann (Blätter ab oder Regler abstecken, Empfängerakku verwenden).
Besser man macht das mit einer losen Stabi und ein paar Servos auf der Werkbank.
Grüßle
Eddi
Born to fly ...
forced to work.
2 mal bearbeitet. Zuletzt am 25.06.2025 15:34 von Eddi E. aus G..
Orpheus
25 June 2025 16:4825.06.2025 16:48
Thanks Eddi, now I understand.
I have a VBar NEO with PRO here that was already intended for the aircraft.
I'll connect all the servos to the stabilizer on the table as an experimental setup and test through the menus and functions.
If I can't solve something, I'll shout really loudly, Edddiiiiii :-)
Thanks again for your help
Greetings, Dietmar
Besten Dank Eddi, jetzt habe ich es verstanden.
Habe ein bereits für den Flieger vorgesehenes VStabi NEO mit PRO hier liegen.
Werde mir mal alle Servos mit dem Stabi am Tisch als Experimentieraufbau verbinden und mich mal durch die Menüs und Funktionen durchtesten.
Sollte ich was nicht lösen können schrei ich ganz laut , Edddiiiiii :-)
Danke nochmal für deine Hilfe
Grüßle Dietmar
Orpheus
28 June 2025 18:5928.06.2025 18:59
Eddi, I still need a little bit of information from you :-)
I still have a VBar EVO with V8 software and PRO/RESCUE update.
Will flashing this to VPlane and installing it in a fixed-wing aircraft offer any additional benefit, or is that a waste of a PRO with RESCUE?
Or would a "only" PRO version have the same features and functions??? :-/
Otherwise, I'd rather use the EVO with PRO/RESCUE in a helicopter again.
Greetings, Dietmar
Eddi, ich brauche doch noch eine kleine Info von dir :-)
Ich habe noch ein V-Stabi EVO mit V8 Software und PRO/RETTUNG Update
Bringt mir das einen zusätzlichen Nutzen wenn ich das auf VPlane flashe und in einen Flächenflieger einbaue , oder ist das Verschwendung von einem PRO mit RETTUNG
Oder würde eine „nur“ PRO die selben Möglichkeiten und Funktionen haben ??? :-/
Sonst verwende ich das EVO mit PRO/RETTUNG lieber wieder in einem Heli
Grüßle Dietmar
Eddi E. aus G.
30 June 2025 09:4230.06.2025 09:42
Hi Dietmar,
To use VPlane, you only need the Pro version; otherwise, the rescue would be 'wasted' :-)
Grüßle
Eddi
Born to fly ...
forced to work.
Moin Dietmar,
um VPlane nutzen zu können, braucht es nur Pro, da wäre die Rettung 'verschwendet' :-)
Grüßle
Eddi
Born to fly ...
forced to work.
Orpheus
30 June 2025 10:0230.06.2025 10:02
Hi Eddi,
I thought so :-)
At least I was able to do some testing and I will use it again for a helicopter.
I'll get a used NEO with PRO for that; V7 will also be sufficient for a simple glider :-)
Thanks Eddi, have a nice day!
Dietmar
Moin Eddi,
das dachte ich mir schon :-)
Dann habe ich wenigstens ein bisschen herumtesten können und werde es wieder für einen Heli verwenden.
Werde mir dafür ein gebrauchtes NEO mit PRO besorgen , V7 wird für einen einfachen Segler ebenfalls ausreichen :-)
Danke Eddi, wünsche dir noch einen schönen Tag
Dietmar
Eddi E. aus G.
30 June 2025 10:5530.06.2025 10:55
Hi Dietmar,
The V8 is purely a helicopter development.
The VPlane is the same for both, and you won't benefit from the better performance of the EVO in terms of flight characteristics, as everything there is rather flat and linear.
Grüßle, und ebenso!!
Eddi
Born to fly ...
forced to work.
Hi Dietmar,
V8 ist ja eine reine Heli-Entwicklung.
Die VPlane ist die selbe, für beide, und in der Fläche wird man auch von der besseren Performance der EVO nicht profitieren, da ist ja alles eher flach und linear ^^
Grüßle, und ebenso!!
Eddi
Born to fly ...
forced to work.