Hello Rainer!
I need your help with my RC Skydiver, as I obviously can't see it... ???
Basically, each servo controls one arm of the jumper, requiring the entire servo travel in each case.
Resting position - no control input, right and left arm/servo in 90 degree position
Roll right or left input, right or left arm moves up to approximately 45 degrees downwards (flying a turn) = Half servo travel
Pulling the pitch stick (from center to bottom), both arms move to approximately 0 degrees at full deflection (pitch fully pulled) = full servo travel
See the manufacturer's video at minute 14:15... Video Link
My approach to programming
CH3 = Re Arm = Mixer of cell 14 (Roll Re Curve / Re Arm Half) and cell 18 (Pitch Pull / Re Arm Full)
Cell 14 = Curve with the points for ROLL input RE (servo travel half)
Cell 18 = Curve with the points for NICK input Drag (Servo travel full)
I'll spare us the left arm here, since we'll implement it right away...
Result:
Everything basically works, but I only get full servo travel when the stick is in the bottom right corner. With full pull on the pitch stick, I lose (some) servo travel...
Where is my mistake? It seems to be the mixing ratio... I'm completely baffled...
Attached are images, and the VPlane Basic and Macrocells files are also included in the ZIP file...
Many thanks for your support!
Geri
Edited twice. Last edited on 07/11/2025 at 16:15 by Dirtygeri.
File attachments:
Open | Download - SKYDIVER.zip (199.6 KB)
I need your help with my RC Skydiver, as I obviously can't see it... ???
Basically, each servo controls one arm of the jumper, requiring the entire servo travel in each case.
Resting position - no control input, right and left arm/servo in 90 degree position
Roll right or left input, right or left arm moves up to approximately 45 degrees downwards (flying a turn) = Half servo travel
Pulling the pitch stick (from center to bottom), both arms move to approximately 0 degrees at full deflection (pitch fully pulled) = full servo travel
See the manufacturer's video at minute 14:15... Video Link
My approach to programming
CH3 = Re Arm = Mixer of cell 14 (Roll Re Curve / Re Arm Half) and cell 18 (Pitch Pull / Re Arm Full)
Cell 14 = Curve with the points for ROLL input RE (servo travel half)
Cell 18 = Curve with the points for NICK input Drag (Servo travel full)
I'll spare us the left arm here, since we'll implement it right away...
Result:
Everything basically works, but I only get full servo travel when the stick is in the bottom right corner. With full pull on the pitch stick, I lose (some) servo travel...
Where is my mistake? It seems to be the mixing ratio... I'm completely baffled...
Attached are images, and the VPlane Basic and Macrocells files are also included in the ZIP file...
Many thanks for your support!
Geri
Edited twice. Last edited on 07/11/2025 at 16:15 by Dirtygeri.
File attachments:
Open | Download - SKYDIVER.zip (199.6 KB)
Hallo Rainer!
Ich ersuche dich um Hilfestellung zu meinem RC SKYDIVER, da ich das offensichtlich nicht sehe ... ???
Grundsätzlich steuert je ein Servo einen Arm des Springers, wobei jeweils der ganze Servoweg benötigt wird.
Ruhestellung - keine Steuereingabe re und li Arm / Servo in 90 Grad Position
Roll re oder li Eingabe, re oder li Arm bewegt sich bis zu ca. 45 Grad nach Unten (Kurve fliegen) = Halber Servoweg
Nick Ziehen (Knüppel von Mitte nach Unten), beide Arme bewegen sich bei Vollausschlag (Nick voll Ziehen) auf ca. 0 Grad (Flair zur Landung) = Voller Servoweg
Siehe Video des Herstellers bei Minute 14:15 ... Video Link
Mein Zugang der Programmierung
CH3 = Re Arm = Mischer von Zelle 14 (Roll Re Kurve / Re Arm Halb) und Zelle 18 (Nick Ziehen / Re Arm Voll)
Zelle 14 = Kurve mit den Punkten für ROLLeingabe RE (Servoweg Halb)
Zelle 18 = Kurve mit den Punkten für NICKeingabe Ziehen (Servoweg Voll)
Den linken Arm erspare ich uns hier, da gleich umzusetzen ...
Ergebnis:
Grundsätzlich funktioniert alles, aber den vollen Servoweg habe ich nur wenn der Knüppel re unten im Eck ist. Bei Nick voll Ziehen verschenke ich (etwas) Servoweg ...
Wo liegt mein Denkfehler ??? Es liegt offenbar am Mischanteil ... Ich stehe auf der Schaufel ...
Anbei Bilder und im ZIP noch die VPlane Basic und Makrozellen Datei ...
Vielen Dank für deine Unterstützung!
Geri
2 mal bearbeitet. Zuletzt am 07.11.2025 16:15 von Dirtygeri.
Dateianhänge:
öffnen | Download - SKYDIVER.zip (199.6 KB)
Ich ersuche dich um Hilfestellung zu meinem RC SKYDIVER, da ich das offensichtlich nicht sehe ... ???
Grundsätzlich steuert je ein Servo einen Arm des Springers, wobei jeweils der ganze Servoweg benötigt wird.
Ruhestellung - keine Steuereingabe re und li Arm / Servo in 90 Grad Position
Roll re oder li Eingabe, re oder li Arm bewegt sich bis zu ca. 45 Grad nach Unten (Kurve fliegen) = Halber Servoweg
Nick Ziehen (Knüppel von Mitte nach Unten), beide Arme bewegen sich bei Vollausschlag (Nick voll Ziehen) auf ca. 0 Grad (Flair zur Landung) = Voller Servoweg
Siehe Video des Herstellers bei Minute 14:15 ... Video Link
Mein Zugang der Programmierung
CH3 = Re Arm = Mischer von Zelle 14 (Roll Re Kurve / Re Arm Halb) und Zelle 18 (Nick Ziehen / Re Arm Voll)
Zelle 14 = Kurve mit den Punkten für ROLLeingabe RE (Servoweg Halb)
Zelle 18 = Kurve mit den Punkten für NICKeingabe Ziehen (Servoweg Voll)
Den linken Arm erspare ich uns hier, da gleich umzusetzen ...
Ergebnis:
Grundsätzlich funktioniert alles, aber den vollen Servoweg habe ich nur wenn der Knüppel re unten im Eck ist. Bei Nick voll Ziehen verschenke ich (etwas) Servoweg ...
Wo liegt mein Denkfehler ??? Es liegt offenbar am Mischanteil ... Ich stehe auf der Schaufel ...
Anbei Bilder und im ZIP noch die VPlane Basic und Makrozellen Datei ...
Vielen Dank für deine Unterstützung!
Geri
2 mal bearbeitet. Zuletzt am 07.11.2025 16:15 von Dirtygeri.
Dateianhänge:
öffnen | Download - SKYDIVER.zip (199.6 KB)
machine-translated from German · Show original