Smartflyer
12 March 2026 00:0912.03.2026 00:09
Hi guys,
Unfortunately, I'm currently despairing over my new project and hope that you might be able to help me.
I wanted to test a different FBL system and have now acquired an RX-only receiver.
The receiver is now set to SBus and also outputs the signal to the FBL via AUX1.
Channel 5 is now displayed/used as the throttle channel, and I can control it via the pitch stick.
also change the value of the gas.
Now I would like to have 3 fixed values for the controller for flying.
So I deleted the previous "Channel" setting with "Input Signal: FC ESC" in cell 15/E1Tail and
I entered a 3-level switch with fixed values.
Unfortunately, my "engine off" switch no longer works.
Is there any way I can configure the macro cell so that I have my 3 fixed values on the bank switch and overwrite the bank value with the motor off switch?
LG
Hi Leute ,
leider verzweifel ich gerade an meinem neuen Projekt und hoffe das Ihr mir vllt. helfen könnt.
Ich wollte ein anderes FBL System testen und habe mir jetzt einen RX-only Empfänger besorgt.
Der Empfänger ist jetzt auf SBus eingestellt und gibt das Signal auch über AUX1 an das FBL raus.
Als Gaskanal wird jetzt Kanal 5 angezeigt/genutzt und über den Pitchknüppel kann ich
auch den Wert vom Gas ändern.
Jetzt hätte ich aber gerne für den Regler 3 Festwerte zum Fliegen.
Also habe ich in der Zelle 15/E1Tail die vorherige Einstellung "Kanal" mit "Eingang Signal: FC ESC " gelöscht und
mir einen 3-Level Schalter mit festen Werten eingetragen.
Leider funktioniert jetzt aber mein "Motor Aus" Schalter nicht mehr.
Gibt es irgendeine Möglichkeit wie ich die Makrozelle so einrichten kann das ich meine 3 festen Werte auf dem Bankschalter habe und mit dem MotorAus Schalter den Wert der Bank überschreibe ?
LG
RV
12 March 2026 07:0812.03.2026 07:08
From the back:
ESC - Channel cell with FS and endpoints, fed by MUX
MUX cell as input source at the top with SW motor as control - input 2 or 3 additional MC depending on position
1 MC Fixed value non-banked for engine off (if required, another one for LL)
1 MC Fixvalue Banked for bank securities
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Von hinten:
ESC - Kanal Zelle mit FS und Endpoints, gefüttert von MUX
MUX Zelle als Zuspieler oben mit SW Motor als Steuerung - Eingang 2 oder 3 weitere MC je nach Stellung
1 MC Fixvalue non-banked für Motor aus (falls erf. für LL noch eine solche)
1 MC Fixvalue Banked für Bankwerte
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Smartflyer
12 March 2026 22:1812.03.2026 22:18
RV wrote:
-------------------------------------------------------
From the back:
>
> ESC - Channel cell with FS and endpoints, fed
> from MUX
> MUX cell as player above with SW motor as
> Control - Input 2 or 3 additional MCs depending on the
> Position
> 1 MC Fixed value non-banked for motor off (if
> another one like this is required for LL)
> 1 MC Fixvalue Banked for bank assets
Awesome, thank you so much!
I just did it with the Mux and it's exactly how I wanted it.
The only thing that doesn't work is the additional safety switch (it can't be selected anywhere).
That's okay, it's only for testing anyway, I'll stick with Vstabi :-)
Edited once. Last edited on 12/03/2026 at 22:20 by Smartflyer.
RV schrieb:
-------------------------------------------------------
> Von hinten:
>
> ESC - Kanal Zelle mit FS und Endpoints, gefüttert
> von MUX
> MUX Zelle als Zuspieler oben mit SW Motor als
> Steuerung - Eingang 2 oder 3 weitere MC je nach
> Stellung
> 1 MC Fixvalue non-banked für Motor aus (falls
> erf. für LL noch eine solche)
> 1 MC Fixvalue Banked für Bankwerte
Mega, vielen Dank !
Habs gerade mit dem Mux so gemacht und ist genau so wie ich das wollte.
Das einzige was nicht klappt ist der zusätzliche Sicherheitsschalter. ( der lässt sich halt nirgendwo auswählen).
Ist aber nicht schlimm, soll ja eh nur zum Testen sein, ich bleibe beim Vstabi :-)
1 mal bearbeitet. Zuletzt am 12.03.2026 22:20 von Smartflyer.
Eddi E. aus G.
13 March 2026 09:1313.03.2026 09:13
Good morning,
Yes, the safety switch assigned in the switch assignment is hardwired to affect the motor logic, specifically the ESC output (safety=OFF regardless of the motor switch position).
But if you bypass the engine logic, it won't work.
And since it refers to the gas value and not to the actual motor switch position (input for your Mux), that's just how it is.
One possible solution is to insert another multiplex with the (physical) safety switch between the channel and the motor multiplex: Safe = OFF, Not Safe = Motor multiplex.
Therefore (motor logic overridden) it is also important to program (and test, BMFA Fail Safe Test App) fail safe in the output channel (last instance) so that the motor is switched off by the VBar in case of emergency.
Grüßle
Eddi
Born to fly ...
forced to work.
Moin,
ja, der in der Schalterzuordnung zugewiesene Sicherheitsschalter wirkt fest verdrahtet auf die Motor-Logik, auf den Ausgang ESC (Sicherheit=AUS egal wo der Motorschalter steht).
Wenn man aber die Motorlogik aushebelt, geht der nicht.
Und da er sich auf den Gaswert bezieht und nicht auf die tatsächliche Motorschalterstellung (Eingang für deine Mux), ist das eben so.
Was man machen könnte, 'ne weitere Mux mit dem (physischen) Sicherheitsschalter zwischen Kanal und Motor-Mux einflechten, Sicher = AUS, Nicht Sicher = Motor-Mux.
Daher (Motorlogik ausgehebelt) auch wichtig, dass man in dem Kanal am Ausgang (letzte Instanz) Fail Safe programmiert (und testet, BMFA Fail Safe Test App), damit der Motor im Fall des Falles von der VStabi ausgeschaltet wird.
Grüßle
Eddi
Born to fly ...
forced to work.
klauserg
25 April 2026 13:0025.04.2026 13:00
Is there any way to query the safety switch (engine off) via the macro cells to, for example, display the switch position via voice output? I haven't found the switch as an input for the macro cells. Perhaps I'm overlooking something.
Lässt sich der Sicherheitsschalter (Moto aus) irgendwie über die Makrozellen abfragen um z.B.: die Schalterstellung per Sprachausgabe anzuzeigen. Habe den Schalter nicht als Eingang für die Makrozellen gefunden. Vielleicht überseh ich da ja was.
RV
26 April 2026 19:2426.04.2026 19:24
No. It's only programmed locally in the VBC as an override for motor switches.
You could also assign him an option which would then appear in the MC's...
But then it only works if you don't bind a different VBC where the OPxx is located somewhere else...
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
1 mal bearbeitet. Zuletzt am 26.04.2026 19:26 von RV.
Nein. Der ist nur lokal in der VBC als Override für Motorschalter programmiert.
Man könnte ihm zusätzlich eine Option zuweisen welche dann in den MC's ...
Aber dann gehts halt nur wenn man nicht ne andere VBC bindet wo der OPxx dann woanders ist ...
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
1 mal bearbeitet. Zuletzt am 26.04.2026 19:26 von RV.