Tgilf
7 June 2026 13:3707.06.2026 13:37
I'm sorry, but I need some advice. I have the OMP Hobby M1 V3 Pro. I've been using it with the Spektrum NX10. Now I'm switching to Vbar Control Touch and have bought the matching VLink S.bus telemetry receiver for micro helicopters. The connection is established via the OMP preset, and I can see the telemetry, etc. Problem: after connecting, there's only a constant beeping from the motor. I can't control the servos or start the motor. It's as if the connection isn't established correctly. In the OMP Hobby app, I've selected SBUS and Vbar telemetry. I would be very grateful if someone could help me. Thanks and best regards, Tom
Es tut mir leid aber ich benötige bitte einen Tipp. Ich habe den OMP Hobby M1 V3 pro. Bisher habe ich ihn mit der Spektrum NX10 benutzt. Jetzt bin ich dabei auf Vbar Control touch umzusteigen und habe mir den passenden VLink s.bus Telemetrie empfänger für Micro Helis gekauft. Die Verbindung wird über das OMP Preset hergestellt und ich sehe die telemetrie etc. Problem: nach dem Verbinden nur konstantes Piepen des Motors ich kann die Servos nicht steuern und auch nicht den Motor starten. So als wäre die Verbindung nicht korrekt hergestellt. In der OMP hobby app habe ich auf SBUS und Vbar Telemetrie gestellt. Würde mich sehr freuen wenn mir jemand helfen kann. Danke und viele Grüße Tom
Tgilf
7 June 2026 14:4307.06.2026 14:43
Addition:
It seems to me it might be related to the throttle. The OMP exhibits the same behavior when I try to connect with the Spektrum transmitter but the throttle switch isn't set to "off". However, the Vbar shows 0 throttle...
Anyone have any ideas?
Ergänzung:
Mir scheint als könnte es etwas mit dem Gas zu tun haben. Das gleiche Verhalten zeigt der OMP wenn ich mit der Spektrum versuche zu verbinden aber den Gas Schalter nicht auf „aus“ habe. Die Vbar zeigt allerdings Gas 0….
Jemand eine Idee?
RV
7 June 2026 17:5207.06.2026 17:52
Moved because it uses VBasic and not VBar. It's a helicopter, but not with our FBL system ;-(
I'll ask if Aaron from OMP can help - he also created the presets.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Verschoben da VBasic und keine VStabi. Ist zwar ein Heli - aber nicht mit FBL von uns ;-(
Ich frag mal ob Aaron von OMP da helfen kann - er hat auch die Presets gemacht.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
thomas1130
7 June 2026 18:3207.06.2026 18:32
Tgilf wrote:
-------------------------------------------------------
> The
The connection is established via the OMP preset.
Which one exactly? - there are several...
You need this for OFS3 for the M1 V3
That works perfectly too :-)
LG
Tgilf schrieb:
-------------------------------------------------------
> Die
> Verbindung wird über das OMP Preset hergestellt
Welches denn genau? - da gibt es verschiedene...
Du brauchst das für OFS3 für den M1 V3
Das funktioniert auch topp :-)
LG
Aaronheli
7 June 2026 19:3107.06.2026 19:31
Hi Tom,
Did you watch the setup video and follow all the steps exactly as described? :-)
OFS3 Setup Video VTUBE German Please verify that you have loaded the correct template.
Simply charge it, don't change anything, then it should work perfectly.
Greetings Aaron
Hallo Tom,
hast du das Setup Video angeschaut und alle Schritte exakt wie dort beschrieben durchgeführt? :-)
OFS3 Setup Video VTUBE deutsch
Bitte verifiziere, dass du auch das korrekte Template geladen hast.
Einfach laden, nix verstellen, dann muss es einwandfrei funktionieren.
Grüße Aaron
Tgilf
7 June 2026 21:1507.06.2026 21:15
Thanks Reiner for forwarding this!
@Aaron:
Thank you so much for your help. It worked after all. I was familiar with your very well-made video and had already tried it before. The difference was this:
Since it was my first model on my new VBar, I didn't use the "Add New Model" function you explained in the video, as it wasn't available, but instead used the Bind button. Now I've added a new model in addition to the bound M1, and it worked. I think that was the problem.
So: a thousand thanks to everyone - it's great how promptly help is provided here.
Best regards
Tom
Danke Reiner für das weiterleiten!
@Aaron:
Vielen Dank für deine Hilfe. Es hat jetzt doch geklappt. Dein sehr gut gemachtes Video kannte ich und habe es auch schon vorher damit versucht. Der Unterschied war folgender:
Da es für mich das erste Modell auf meiner neuen VBar war habe ich es nicht über die von dir im Video erklärte Funktion "Neues Modell hinzufügen" gemacht, da es diese nicht gab, sondern über den Binden Button. Jetzt habe ich ein neues Modell zusätzlich zu dem gebundenen M1 hinzugefügt und es hat geklappt.. Denke da lag der Fehler.
Also: tausend Dank an alle - Super wie prompt hier geholfen wird.
Liebe Grüße
Tom