← VPlane / VBasic VLink

OMP M2 V3 Pro + Receiver 05680 – Governor/Speed Control Not Working translated

VBar › VPlane / VBasic VLink · Started by sonorsonic on 13 June 2026 15:4013.06.2026 15:40
sonorsonic 13 June 2026 15:4013.06.2026 15:40
Hello everyone,

I am trying to operate an OMP M2 V3 Pro with the 05680 receiver and VBar Touch.

I have already taken the following steps:

- Everything was connected and set up according to the instructional video.
- VBar Touch updated to the latest version.
- The firmware M2V3Pro.015.20.fw was loaded onto the helicopter.
- The appropriate setup was loaded from VBar multiple times and the entire setup process was repeated several times.

My problem:

The throttle is still controlled directly via the throttle stick from 0 to 100%. Instead of a fixed head speed, the system behaves like in normal throttle mode.

Regardless of whether I select bank 1, 2, or 3, the engine does not automatically rev up to the preset RPM. The RPMs set in the individual banks are apparently not being applied.

Does anyone have any idea what the cause might be or what setting I might have overlooked?

Thank you so much for your support.

Kind regards
Raphael
machine-translated from German · Show original
Aaronheli 13 June 2026 23:0813.06.2026 23:08
Hello Raphael,

That's actually strange. OFS3 isn't designed to fly with a linear throttle channel. It shouldn't even work.
Could you please activate the "Software Throttle" function in the OFS3 app? This will control the engine speeds that are set in the app.

What about that?

Greetings Aaron
machine-translated from German · Show original
sonorsonic 14 June 2026 09:0614.06.2026 09:06
Hi Aaron,

After further tests, I found the following:

Whether I activate the "Software Throttle" function or not – as long as the throttle stick is all the way down, the engine will not start, regardless of which bank I am in.

When I move the throttle stick upwards, the engine slowly revs up to the corresponding speed. If the stick is in the middle, for example, and I switch banks, it also switches to a different speed. So that seems to work in principle.

The only problem is that the motor doesn't turn when the throttle stick is in the lowest position. Pitch control, however, works perfectly normally.

It would be nice, of course, if the thing didn't shut down immediately when a negative pitch is given. ;-)

For context: I've already used the system with Radiomaster, FrSky, and Spektrum transmitters (I work in a model shop and wanted to familiarize myself with the different systems). The helicopter flew perfectly with each of them. Therefore, I don't suspect the problem lies with the helicopter itself.

Greetings
Raphael
machine-translated from German · Show original
RV 14 June 2026 11:2414.06.2026 11:24
Raphael,

Something is fundamentally wrong with your setup. Was the MacroCells app downloaded before (!!!) the setup was installed?

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
sonorsonic 14 June 2026 12:5514.06.2026 12:55
Hello Rainer,
Yes, the macrocell app was already downloaded. I had it previously installed on the VBar.
Greetings
Raphael
machine-translated from German · Show original
RV 14 June 2026 15:0314.06.2026 15:03
Please note, there is a common misconception that repeatedly leads to confusion:

VBar (EN) = VBar (DE) = Flight control system for helicopters
VBar Control (classic, touch, EVO, Basic), abbreviated VBC = transmitter from Mikado

I think you mean the VBar Control.

Please save both the model and MC setup to the VBC and wait until it has "clouded out". That is, until you see it in your cloud.

Then tell me the serial number of your VBC here - and I'll take a look at it.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.




1 mal bearbeitet. Zuletzt am 14.06.2026 15:04 von RV.
machine-translated from German · Show original
Aaronheli 14 June 2026 17:1814.06.2026 17:18
Hello Raphael,

As Rainer already suspected, something isn't right here.
I just reloaded the latest setup. Everything works perfectly for me.

Please check the model motor settings and macro cell 13. This controls the throttle channel and should have the following fixed values "out of the box": -18% on bank 1, -48% on bank 2 and -68% on bank 3. (With S.Bus, the throttle channel is reversed)

Attached is an image for comparison. This is how it should look after loading the setup.

machine-translated from German · Show original
sonorsonic 14 June 2026 17:5914.06.2026 17:59
@Rainer I meant the VBar Control. I have a Touch version and have already uploaded the data. The serial number is: 11002171.

@Aaron My settings are the same as in your photos. The values also cycle through like this: -18, -48, -68. However, they are only displayed when I push the throttle stick upwards, regardless of which bank I'm in. The values are displayed correctly for each bank, though.

However, the engine will not start if the throttle stick is in the lowest position.
machine-translated from German · Show original
RV 14 June 2026 21:2514.06.2026 21:25
Please check your stick calibration... and recalibrate all sticks, especially pitch. I bet it's already showing -100% before it's even at the bottom ;-)

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.




1 mal bearbeitet. Zuletzt am 14.06.2026 21:26 von RV.
machine-translated from German · Show original
sonorsonic 14 June 2026 22:4714.06.2026 22:47
It was due to the throttle stick calibration. Now everything works perfectly!
Thank you so much for your help.
Greetings
Raphael
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless