← VPlane / VBasic VLink

Vbar NEO mini rx only => Flybeam 2 translated

VBar › VPlane / VBasic VLink · Started by Wiesel1005 on 9 October 2026 18:1109.10.2026 18:11
Wiesel1005 9 October 2026 18:1109.10.2026 18:11
Hello folks...

I've been struggling and getting frustrated all day and can't find a solution.
I recently bought a Vbar Control Touch and want to start flying helicopters. However, I also want to continue flying fixed-wing aircraft with the VBCT. I've now acquired a Vbar NEO mini (7-channel).
I can't even get the first plane to work... Everything works except for the throttle via the receiver's ESC output.

Finally, I figured out that if I connected the controller to CH1, it worked. However, that's not a solution for me, because if I already have an ESC output, safety switch, and motor cutoff, then I want to use them correctly.
I've tried everything, even the programming mode... But I just can't get it to work with the ESC port...

Perhaps someone can help me. I would be very grateful...

Thanks and best regards
Gerald
machine-translated from German · Show original
RV 9 October 2026 21:1409.10.2026 21:14
Hello Gerald,

- What is the reaction at the ESC when you connect a servo there? - As expected?
- What is the difference to the servo on CH1?
- Which controller is it? - If it's one of our recommended models with integrated telemetry, it will automatically recognize paths, etc. If not, => you might have to go through the old-fashioned, self-imposed setup process like they did 100 years ago, using the learning mode first.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
Fingolf 9 October 2026 22:1009.10.2026 22:10
The controller is from Aerostar. That means nothing to me, and probably not to Rainer either.
The controller's instruction manual is definitely important. It must describe how
he is being trained.
Then, as Rainer already writes, the classic old way with the gas pedal up/down, doo-doo.

Stephan
machine-translated from German · Show original
Wiesel1005 10 October 2026 15:3610.10.2026 15:36
Hello Rainer,

So, for example, if I connect the controller to CH2 and then the rudder to ESC, it moves with the stick movement as it should... So that's not the problem...
But as soon as I connect the controller to the ESC and try to program it, it just doesn't work... I spent ages fiddling with it yesterday, but no luck... I'm at my wit's end and getting desperate... It does work if I connect the controller to CH1, but that's not ideal...

Unfortunately, I can't find any instructions for this controller on how to program it... But the strange thing is: I can program CH1 using the old method just fine...

lg
Gerald
machine-translated from German · Show original
RV 10 October 2026 21:4310.10.2026 21:43
This leads me to two questions in order to understand this 1:1:

- How exactly do you proceed with the CH1 learning process?

- How exactly do you proceed when teaching the ESC key?

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless