← VBar NEO/EVO VLink

Vbar Neo-mini

VBar › VBar NEO/EVO VLink · Started by xerolift on 25 November 2025 23:2625.11.2025 23:26
xerolift 25 November 2025 23:2625.11.2025 23:26
2 part question

can Vplane be put on the Neo-mini?
(it already has pro+rescue)

can the Neo-mini servo bus support micro servos on a 420 machine?

sorry for posting here. the site keeps redirecting me to the German forum from the English forum.
Eddi E. aus G. 26 November 2025 09:1926.11.2025 09:19
Hi,

VBar NEO mini has VPlane available (Pro or Pro+Rescue required).

I don't quite understand the servo question, though.
Power-wise, all VBars output the same voltage as the input voltage, like on a power rail.
Signal-wise, VBar NEO outputs 144 Hz on the swash plate (which is OK for like _all_ digital servos) and adjustable center pulse and pulse width on the tail (which should provide working settings for like _all_ digital servos).

On the other hand, where you can install midi servos, you should, not micros, and where you can install standard size servos, you should, not midi.
The performance is always better, and particularly on a helicopter, all there is between the VBar and the rotor head are the servos, so servo performance is key.

Analog servos are not supported, but who has those anyway, any more, on helicopters?

In VPlane, though, the refresh rate defaults to 70 Hz, which is also good for analog servos e.g. on cheapo ARF foamies or such.

Kind regards

Eddi

Born to fly ...
forced to work.
xerolift 26 November 2025 11:4326.11.2025 11:43
the folks at Mikado USA(peter) told me that I couldn't use the Neo-mini with midi servos on a Goblin Raw 500 because the servo b us couldn't handle the amp draw
Eddi E. aus G. 26 November 2025 14:1526.11.2025 14:15
Hmm ... as long as Uli is not contradicting, I guess Peter assumes wrongly.

Or he mixed it up with NEO micro, with the tiny JST-type servo connectors and bell wire.
But imo also there, the connector type is a limiting factor, not necessarily the mainboard. Still ...

But ... NEO mini has never been fully tested with and approved for other models than LOGO 200, mainly when it comes to vibration resilience, and in particular with Rescue: NEO mini has only the 16 G accelerometer, where the full size NEO has that plus a 200 G accelerometer.

Kind regards

Eddi

Born to fly ...
forced to work.
xerolift 27 November 2025 16:3427.11.2025 16:34
thank you, Eddi
ulrich 27 November 2025 20:0627.11.2025 20:06
Eddi is 100% right. The powerbus is similar capable to the NEO and EVO.

so long ... Uli
http://www.vstabi.de
Vinger 15 December 2025 15:2015.12.2025 15:20
As I was involved here, let me explain.

I never mentioned the powerbus but did explain it not being a good idea as the mini Neo does not have the same gyros in it as a Neo and would not advise it to be used on larger than200 size helicopters.

Cheers

VControl, VBar on all.
TDR, TDR2, TDF, TDS and TDSF
Peter
Eddi E. aus G. 16 December 2025 09:0616.12.2025 09:06
Hi again,

I see.

Anyway, as already stated, what speaks against NEO mini on larger helicopters is basically the use of Rescue, and I also wouldn't recommend it on nitros, even smaller ones.
If you just use it as a flybarless (with Pro, for example, or disable Rescue on that model), you should be good.
Another thing is, Lightness also makes use of the accelerometers, so that feature could also be off over time (make collective feel weird), with vibration/resonance. So better leave that one off, too.

Still, this is not carte blanche, just some thoughts from the sidelines.

Best,

Eddi

Born to fly ...
forced to work.
VStabi VStabi Pioneer of Flybarless