surf10plus23@gmail.com
18 January 2026 13:0018.01.2026 13:00
Vbar evo 7.1 with futaba 16iz and futaba R7206SB rx, kontronik helijive 120, do I need to change throttle esc to aux 3 to control rpm?, i currently have it plugged into esc channel, channel 3, and on the setup page you can see the throttle percentage change when you select bank 1 bank2 bank 3, on spool up the esc goes through its normal soft start and then when its in the air and the esc continues to spool to maximum rpm, what's the reason for this?
2 mal bearbeitet. Zuletzt am 18.01.2026 13:07 von
surf10plus23@gmail.com.
RV
19 January 2026 07:3219.01.2026 07:32
The ESC out is just a fixed signal.
If something strange is happening here - check the outcome with a servo or something else. Consider the "external Gov" needs to be set in the PC Software.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
The ESC out is just a fixed signal.
If something weired is happening here - check the outcome with a servo or something else. Consider the "external Gov" needs to be set in the PC Software.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Eddi E. aus G.
19 January 2026 09:1319.01.2026 09:13
Hi,
please consider that Kontronik ESCs work best with their internal Governor (Mode 4 plus add-ons), which is External Governor from our perspective, they don't with VBar Governor Mode.
If set so, ESC will output the throttle values (percent) you set in the Setup software, per bank.
If set to VBar Governor Mode, the VBar will adjust throttle to the RPM signal it reads (if/when connected), and this will mess with the Kontronik's internal logic.
So far, so clear.
Switching to AUX3 (wire and original throttle channel from the transmitter) has one benefit, for use with third party radio equipment: you can easily adjust throttle at the field, no computer required.
Fail safe will still work, the VBar will cut the signal in such a case. Please check anyway, run the model without blades, switch off transmitter, the motor must stop, for safety reasons.
We still strongly recommend you set up the throttle logic (assign motor switch positions) so the VBar can log motor switch actuations, this can help with trouble shooting (e.g. ESC cuts out, was it the pilot or the ESC itself?).
Leaving it on ESC has the other benefit, if someone with a VBar Control is around, he can help making adjustments, and even fly the model with his transmitter, or buddy box you. With AUX3, VBar Control wouldn't know.
Best,
Eddi
Born to fly ...
forced to work.
surf10plus23@gmail.com
19 January 2026 23:4319.01.2026 23:43
When programming the esc do you have to be in the vbar software and select throttle stick control to collective stick control ? Or this is not a factor?
I going to use mode 4 with auto rotation bailout, without vbar governor.
5 mal bearbeitet. Zuletzt am 20.01.2026 07:34 von
surf10plus23@gmail.com.
Eddi E. aus G.
20 January 2026 09:5820.01.2026 09:58
Hi,
to program a Kontronik via transmitter, use Model Setup / Edit Setup / all the way down: Output Setup / Collective Control.
Do the stick-beep procedure as per Kontronik's instructions, program Mode 1 first (to reset the ESC), then Mode 4 and add ons.
You can power-cycle the VBar, only disable when you're done.
Kind regards
Eddi
Born to fly ...
forced to work.
surf10plus23@gmail.com
20 January 2026 12:2820.01.2026 12:28
Thank you guys for all your help I will try that this weekend
surf10plus23@gmail.com
24 January 2026 07:2824.01.2026 07:28
Okay so I setup my futaba 16iz so that the throttle hold switch all the way up position is motor off center position is idle and off is down, just like vbar tutorials say, im using the banks to adjust my headspeeds I punched in the throttle percentage on the setup page,they all work as the tutorials, I programmed my esc off the gov 2 page select throttle controlled by collective pitch curve, programmed mode 1 and mode 4 and motor direction mode7, my question is if you are using the collective pitch curve for throttle curve it not possible to program bailout mode in the helijive because the throttle hold is not effective due to the collective curve being selected, what is the best course of action?
1 mal bearbeitet. Zuletzt am 24.01.2026 13:04 von
surf10plus23@gmail.com.
Eddi E. aus G.
26 January 2026 09:5526.01.2026 09:55
Hi,
I'm not familiar with that programming any more, and much less with the subtleties between ESC types or firmwares—what's required to program bailout mode?
Iirc on some/later Kontronik ESCs, the transmitter had to be set to 25 % throttle in bailout configuration, so the ESC knew what was going on.
That would mean, you set the Autorotation (Throttle) value on the Main Screen, External Governor box, to 25, and that will apply when the motor switch is switched _back_ from Run position to Idle (center) position (while not when switched _forward_ from Stop over Idle to Run, to prevent hot starts when afterwards switching from Idle to Run, with quick spool up).
Kind regards
Eddi
Born to fly ...
forced to work.
surf10plus23@gmail.com
28 January 2026 10:4428.01.2026 10:44
Yes I believe its 25 percent , Im still having higher headspeeds than what it should be according to calculator, at 50 percent it should be 1200 to 1300 rpm , it is 12s, 520kv 8.46 main gear ratio , auto bailout when I was using the pitch curve requisite mode 4 programming with a linear curve amd then you flip to -60 and its within idle mode and the esc detects the radios throttle idle middle position for bailout
https://kontronik.com/wp-content/uploads/2023/03/HELI-JIVE-1.pdf
Eddi E. aus G.
28 January 2026 13:3728.01.2026 13:37
Hi,
well that calculated rpm kind of never worked for me. Pack voltage and actual kv vs. labelled kv and lack of linearity to begin with do that for you, I guess.
These ESCs worked best for me when set up so they ran at my preferred high rpm at approx. 65 % throttle, with full batteries fresh from the charger, which left enough headroom increase throttle with dropping voltage, and to govern, until the battery was empty.
But I never was into insanely high rpm and hard 3D anyway.
We introduced autorotation idle as a default mode for electrics early, with VBar Governor, and recommended to set it as low as the ESC would go before stopping.
This was to prevent damage (when the ESC has to get into commutation again from off, without having a reading on it's rpm by means of the rotating magnetic field, while the motor is still spinning, this can cause troubles) and to allow for a quick spool-up when necessary, to abort an autorotation.
Somewhat later, ESC manufactures implemented their own versions.
Best,
Eddi
Born to fly ...
forced to work.
surf10plus23@gmail.com
30 January 2026 23:5230.01.2026 23:52