Vortex_182
15 December 2025 23:0415.12.2025 23:04
Hello,
I acquired an older Tornado glider that had been converted from flybar to flybarless. It originally had a MicroBeast airfoil, which is now being replaced by a NEO Evo.
After completing the setup, I noticed that I have significantly too much cyclic travel on pitch and roll. Is it possible to reduce the pitch and roll endpoints on the NEO Evo? Unfortunately, I haven't been able to find any information on this.
Everything worked perfectly with the MicroBeast, as the cyclic travel could be limited accordingly. While reducing the size of the servo arms would be an option, it would require a complete disassembly of the helicopter, which I'd prefer to avoid.
Greetings
Luca
Hallo,
Ich habe einen älteren Tornado übernommen, der von Flybar auf Flybarless umgebaut wurde. Verbaut war ursprünglich ein MicroBeast, welches nun durch ein NEO Evo ersetzt wird.
Nachdem ich das Setup abgeschlossen habe, ist mir aufgefallen, dass ich deutlich zu viel zyklischen Weg auf Nick und Roll habe. Kann man beim NEO Evo die Endpunkte für Nick und Roll reduzieren? Leider habe ich dazu keine Informationen gefunden.
Mit dem MicroBeast lief alles problemlos, da man dort den zyklischen Weg entsprechend begrenzen konnte. Das Verkleinern der Servohebel wäre zwar eine Möglichkeit, würde jedoch eine komplette Zerlegung des Helis erfordern, was ich eigentlich vermeiden möchte.
Grüße
Luca
cc1975
16 December 2025 04:5516.12.2025 04:55
Have you set the 8 degrees cyclically? There's also a cyclic ring for adjustment; this value is set to 85 by default. You might need to reduce this value to prevent the servos from over-rotating at the end points.
Regards, Christian
Hast du zyklisch die 8 Grad eingestellt? Des Weiteren gibt es den zyklischen Ring zum Einstellen, dieser Wert liegt Standardmäßig bei 85. Kann sein dass du diesen reduzieren musst damit die Servos nicht anlaufen in den Eckpunkten.
Gruß Christian
Vortex_182
16 December 2025 08:4216.12.2025 08:42
Hello Christian,
The cyclic setting is exactly 8 degrees. I'm familiar with the cyclic ring setting from the PC software. I haven't yet found the corresponding setting in the VBar Control.
Greetings Luca
Hallo Christian,
Zyklisch sind genau 8 Grad eingestellt. Die Einstellung des zyklischen Rings kenne ich noch aus der PC-Software. In der VBar Control habe ich den entsprechenden Einstellpunkt bisher noch nicht gefunden.
Grüß Luca
Eddi E. aus G.
16 December 2025 09:1116.12.2025 09:11
Hi Luca,
What values do you get for 8° cyclic and 12° pitch in the setup?
They are a good indicator of whether the mechanics have good geometry or not.
The cyclical fluctuations outside the setup are irrelevant, as the control loop does not self-calibrate when stationary on the ground without sensor feedback.
It would be relevant again if something mechanically activated cyclically around approximately 50% pitch (half the stick deflection, in this example +/- 6°).
Then you could use the cyclic ring (in VBar Control on the swashplate, long click, scroll down), but it's better not to go below about 71%, otherwise you start cutting off the control loop (agility and reaction) at the wrong end, which makes no sense.
When in doubt, then... off to the workbench! ^^
—Eddi
Born to fly ...
forced to work.
Moin Luca,
auf welche Werte kommst Du denn, für 8° zyklisch und 12° Pitch, im Setup?
Die sind ein guter Indikator dafür, ob die Mechanik eine gute Geometrie hat, oder nicht.
Die zyklischen Ausschläge außerhalb des Setups sind irrelevant, da der Regelkreis sich im Stand am Boden ohne Sensor-Rückmeldung nicht selbst einpegelt.
Relevant wäre wieder, wenn bei etwa 50 % Pitch (halber Knüppel-Ausschlag, in dem Beispiel +/– 6°) und zyklisch rundum etwas mechanisch angeht.
Dann könnte man den zyklischen Ring verwenden (in VBar Control auf der Taumelscheibe, Langklick, runter scrollen), aber besser auch nicht unter etwa 71 %, sonst fängt man an, den Regelkreis (Wendigkeit und Reaktion) am falschen Ende zu beschneiden, was keinen Sinn ergibt.
Im Zweifel, dann, ... ab an die Werkbank ^^
—Eddi
Born to fly ...
forced to work.
Vortex_182
16 December 2025 20:0316.12.2025 20:03
Hi Eddi,
Attached is the screenshot with the settings: ±12 degrees collective and cyclic ±8 degrees.
At ±6 degrees cyclically (cyclic ring 85), the servos do not start in the stick center.
If I set the cyclic ring to 75 and cyclically adjust ±8 degrees, the servos also do not run against the stop.
Which is the better setting here: cyclic ±6 degrees with ring 85 or ±8 degrees with ring 75?
Greetings Luca
Hallo Eddi,
anbei der Screenshot mit den Einstellungen: ±12 Grad kollektiv und zyklisch ±8 Grad.
Bei ±6 Grad zyklisch (zyklischer Ring 85) laufen die Servos in Knüppelmitte nicht an.
Wenn ich den zyklischen Ring auf 75 stelle und zyklisch ±8 Grad einstelle, laufen die Servos ebenfalls nicht gegen den Anschlag.
Was ist hier die bessere Einstellung: zyklisch ±6 Grad mit Ring 85 oder ±8 Grad mit Ring 75?
Grüße Luca
RV
17 December 2025 06:2717.12.2025 06:27
Quote: Cyclic ±6 degrees with ring 85 or ±8 degrees with ring 75?
The system always cyclically sets the temperature to 8°. The control system needs to know this reference point – if it's incorrect, the overall balance (gains, direct proportions, etc.) will also be shifted and must be compensated for.
Then limit CR as before against running into suspended pitch.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Quote:zyklisch ±6 Grad mit Ring 85 oder ±8 Grad mit Ring 75?
Zyklisch wird IMMER auf 8° eingestellt. Die Regelung muss diesen Anhaltspunkt wissen - stimmt das nicht ist die Gesamtabstimmung (Gains, Direktanteile etc.) auch verschoben und muss gegenkompensiert werden.
Danach mit CR begrenzen wie gehabt gegen Auflaufen in Schwebepitch.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Eddi E. aus G.
17 December 2025 09:0617.12.2025 09:06
Good morning,
I hope he means the requested 50% pitch for all-around steering by the 6° :-)
Otherwise... as Rainer writes, 8° is mandatory, and CR 75.
And then everything would be OK in my opinion, the limits for 8° and 12° are close enough to 80 and the CR at 75 is also OK.
Of course, one could still improve the servo arms a bit, provided one doesn't create any new problems, for example, regarding other mechanical aspects, the chassis, or the servo housings.
It could also help if, for example, you have wobbling or similar issues, to give the servos more room to breathe, more resolution.
But with good digital servos... go flying, have fun.
Grüßle
Eddi
Born to fly ...
forced to work.
2 mal bearbeitet. Zuletzt am 17.12.2025 09:08 von Eddi E. aus G..
Moin,
mit den 6° meint er hoffe ich die gefragten 50 % Pitch beim Rundumsteuern :-)
Sonst ... wir Rainer schreibt, zwingend 8°, und CR 75.
Und dann wäre es mMn alles OK, die Limits für 8° und 12° nahe genug bei 80 und der CR bei 75 ist auch OK.
Natürlich könnte man es noch etwas verbessern an den Servohebeln, wenn man sich sonst keine neuen Probleme einhandelt, dass bspw. was anderes mechanisch angeht, am Chassis oder an den Servogehäusen.
Könnte auch helfen, wenn man bspw. ein Wobbeln o. ä. hat, wenn man den Servos mehr Luft zum Atmen, mehr Auflösung lässt.
Aber mit guten Digitalservos ... fliegen gehen, Spaß haben.
Grüßle
Eddi
Born to fly ...
forced to work.
2 mal bearbeitet. Zuletzt am 17.12.2025 09:08 von Eddi E. aus G..
Vortex_182
17 December 2025 17:3517.12.2025 17:35
Quote: I hope he means the requested 50% with the 6°.
Pitch during all-around steering
That's exactly what was meant.
Quote: Otherwise ... as Rainer writes, mandatory 8°, and CR 75.
Okay, then I'll set up the helicopter like that and go fly it.
Thanks for the help
Greetings Luca
Edited twice. Last edited on 17.12.2025 at 17:37 by Vortex_182.
Quote:mit den 6° meint er hoffe ich die gefragten 50 %
Pitch beim Rundumsteuern
Genau so war es gemeint.
Quote:Sonst ... wir Rainer schreibt, zwingend 8°, und CR 75.
Alles klar, dann stelle Ich den Heli mal so ein und geh damit fliegen.
Danke für die Hilfe
Grüße Luca
2 mal bearbeitet. Zuletzt am 17.12.2025 17:37 von Vortex_182.
Vortex_182
20 December 2025 20:2920.12.2025 20:29
Hello,
The maiden flight went well so far.
I have another question regarding the translation of the Nitro Governor.
The instructions state a translation ratio of 7.62 : 1 : 5.
What settings do I need to adjust in NEO?
At idle, the engine already shows 700 rpm (1 magnet is installed and set to 1 pole).
Thank you and best regards
Luca
Hallo,
der Erstflug hat soweit gut geklappt.
Ich habe noch eine Frage bezüglich der Übersetzung beim Nitro Governor.
Laut Anleitung ist eine Übersetzung von 7,62 : 1 : 5 angegeben.
Was muss ich dafür im NEO einstellen?
Im Leerlauf werden mir bereits 700 U/min angezeigt (verbaut ist 1 Magnet und eingestellt 1 Pol).
Danke und viele Grüße
Luca
RV
20 December 2025 20:5520.12.2025 20:55
I'm assuming 7.62; the 5 is the tail rotor.
And then just 1 pole.
The reading is correct at idle, as the engine is already providing RPM. Otherwise, install a sensor on the main shaft.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Ich gehe von 7,62 aus, die 5 ist der Heckrotor
Und dann eben 1 Pol.
Im LL ist die Anzeige dann schon richtig, der Motor liefert ja schon RPM. Andernfalls einen Sensor an der Hauptwelle verbauen.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.