mf_powerfly
1 January 2026 09:1101.01.2026 09:11
Hello everyone, Happy New Year!
I received the Vbar Control EVO+ and 2 VBar EVO (Express) on Tuesday.
I've been flying with Vstabi and a third-party transmitter for ages and never had any problems. I can't get a binding with the Vbar Control.
Out of the box, I followed all the instructions on the website (setup). Binding is actually quite simple, but my transmitter can't find the Evo. No matter how I try, according to the manual, there are two possibilities: the Evo goes into binding mode, but the transmitter can't find it.
I then registered the Evo, but still no binding.
Since I'm a Mode 1 pilot, I modified the transmitter according to the instructions. You can't really go wrong with that...
I googled it, and the AI always comes up with ideas that are useless.
Is it possible that I overlooked something in the transmitter during the initial setup?
Thank you in advance.
Mario
Hallo zusammen, Prosit Neujahr!
Ich habe am Dienstag die Vbar Control EVO+ und 2 VStabi EVO (Express) geliefert bekommen.
Fliegen tue ich schon ewig mit Vstabi und Fremdsender, hatte nie Probleme. Bei der Vbar Control bekomm ich keine Bindung.
Out of the box, habe ich alles wie auf der Homepage (Inbetriebnahme) gemacht. Eigentlich ist binden ganz einfach, aber mein Sender findet das Evo nicht. Egal wie ich es versuche, lt. Anleitung gibt es zwei Varianten. Das Evo geht in den Bindemodus, der Sender findet nicht.
Habe dann das Evo registriert, trotzdem keine Bindung.
Da ich ein Mode 1 Pilot bin hab ich den Sender lt. Anleitung umgebaut. Hier kann man ja auch keinen Fehler machen...
Ich hab gegoogelt, die KI hat auch immer so Ideen mit denen man nichts anfangen kann.
Kann es sein das ich irgendwo in der Funke was übersehen habe bei der Inbetriebnahme?
Vielen Dank im Voraus
Mario
Fingolf
1 January 2026 09:3301.01.2026 09:33
Motor switch off?
Stephan
Motor Schalter auf Aus?
Stephan
mf_powerfly
1 January 2026 10:2901.01.2026 10:29
Yes, it's off.
I also tried binding the second stabilizer. First without registration, then with registration.
It doesn't bind either.
Ja, ist auf aus.
Hab auch das zweite Stabi versucht zu binden. Ohne Registrierung, dann mit Registrierung.
Bindet auch nicht.
ulrich
1 January 2026 11:3701.01.2026 11:37
Is the EVO flashing red/green? Does the flashing speed up after 10 seconds? Are you close to binding (binding works with very low power)? Registration is unrelated. It should always work...
So long... Uli
http://www.vstabi.de Edited once. Last edited on 01/01/2026 at 11:38 by ulrich.
Blinkt die EVO rot/grün? Wird das blinken schneller nach 10sek? Bist du nah dran beim Binden (binden geht mit ganz geringer Leistung)? Registrieren hat damit nicht zu tun. Sollte immer gehen...
so long ... Uli
http://www.vstabi.de
1 mal bearbeitet. Zuletzt am 01.01.2026 11:38 von ulrich.
mf_powerfly
1 January 2026 12:2001.01.2026 12:20
Evo first flashes blue, after 10 seconds red/green, after another 5 seconds the red/green flashing becomes faster.
I have everything laid out in front of the PC, the Evo is right next to the transmitter. I've also tried a greater distance, because that's what I read on the internet.
Mario
Evo blinkt zuerst blau, nach 10sec rot/grün, nach weiteren ca. 5sec wird das rot/grün blinken schneller.
Habe alles vor dem PC liegen, Evo liegt gleich neben dem Sender. Hab auch weiteren Abstand schon versucht, weil man das im Internet liest.
Mario
RV
1 January 2026 16:0601.01.2026 16:06
Hello Mario,
Here's my question from last year's email again. Please clarify this and post the answer. We'll continue the discussion here.
Quote: What happens when you're about 2 meters away with the VBC?
If you update it via USB - which serial number is displayed? Which firmware version is shown?
USB - with VBC Manager and please refer to the FAQ for VBar EVO (connection sequence as there is no boot plug like NEO).
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Hallo mario,
hier meine Frage aus der Mail nochmals von letztem Jahr. Bitte das mal klären und posten. Wir machen dann hier weiter.
Quote:
Wie ist es wenn Du ca. 2m weg bist mit der VBC?
Wenn Du sie per USB updatest - welche SN wird angezeigt? Wenlceh Firmware wird da angezeigt?
USB - mit VBC Manager und bitte FAQ zur VStabi EVO beachten (Ansteckreihenfolge da kein Boot Plug wie NEO).
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
mf_powerfly
1 January 2026 16:3501.01.2026 16:35
Hello Rainer,
At a distance of 2m, tying according to instructions option 1 and 2, does not work.
VBC Manager shows:
SN: 27010376
Version 7.1.30
Greetings
Mario
Hallo Rainer,
mit 2m Entfernung, binden nach Anleitung Möglichkeit 1 und 2, funktioniert nicht.
VBC Manager zeigt:
SN: 27010376
Version 7.1.30
Grüße
Mario
RV
1 January 2026 17:3001.01.2026 17:30
I'd like to toggle the stabilization to VBasic, then please update and try binding with that setting. If it works, we'll toggle it back and test again.
It's important that it doesn't have servos/controllers. Let me know when I can do that.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Ich würde die Stabi gerne einmal nach VBasic toggeln, dann bitte Updaten und damit versuchen zu Binden. Wenns geht toggeln wir wieder zurück und testen erneut.
Wichtig wäre dass sie dabei nicht mit Servos/Regler versehen ist. Sag Bescheid wenn ich das tun kann.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
mf_powerfly
1 January 2026 18:0401.01.2026 18:04
I have the computer running, we can do that. Whatever works for you.
My setup is brand new, straight out of the box. It only has the BEC battery contact :-)
Greetings
Mario
Ich hab den Rechner laufen, können wir machen. So wie es dir ausgeht.
Mein Setup ist neu, out of the Box. Hat nur den BEC Akku kontakt :-)
Grüße
Mario
RV
1 January 2026 18:3901.01.2026 18:39
Then update and let me know.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Dann update mal und sag Bescheid.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
mf_powerfly
1 January 2026 19:3601.01.2026 19:36
Thank you for your time on the holiday!!!
No binding with VBasic. I flashed back to Vbar. Still no binding. That's not normal. I've never had binding problems before – with other brands.
Did I get a bad station? Is there a software bug in the transmitter? Or did I forget to activate something?
I followed your video to set up the transmitter.
I can gladly send everything in.
Regards, Mario
Danke für deine Zeit am Feiertag!!!
Keine Bindung mit VBasic. Hab wieder zurück auf Vbar geflasht. Keine Bindung. Ist ja nicht normal. Hatte noch nie Probleme mit binden - mit anderen Fabrikaten.
Hab ich einen Montagssender erwischt? Softwarefehler in der Funke? Oder habe ich etwas vergessen zu aktivieren?
Ich habe nach deinem Video die Inbetriebnahme des Senders gemacht.
Ich kann auch gerne alles einschicken.
Gruß Mario
Fingolf
1 January 2026 20:1601.01.2026 20:16
No binding dialog appears?
It would be best if you took a screenshot showing where you are on the channel.
Es kommt kein Bindedialog?
Mach am besten mal einen Screenshot wo im Sender du da bist.
mf_powerfly
1 January 2026 20:5901.01.2026 20:59
I press "bind". Then the field appears where the detected stabilizer is normally displayed.
But it remains empty.
Ich drücke auf binden. Dann kommt das Feld wo normal das erkannte Stabi angezeigt wird.
Das bleibt aber leer.
mf_powerfly
1 January 2026 21:2201.01.2026 21:22
Fingolf wrote:
-------------------------------------------------------
No binding dialog appears?
> It would be best if you took a screenshot of where in the channel
> you are there.
Fingolf schrieb:
-------------------------------------------------------
> Es kommt kein Bindedialog?
> Mach am besten mal einen Screenshot wo im Sender
> du da bist.
RV
1 January 2026 21:4601.01.2026 21:46
That's strange. Can you at least click on the field where the symbol normally appears to bind it?
But we have one last weapon... switch the VBC to EN and test it.
Let me know if anything changes.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
1 mal bearbeitet. Zuletzt am 01.01.2026 21:47 von RV.
Das ist schon merkwürdig. Kannst Du denn das Feld wo das Symbol normalerweise erscheint wenigstens mit anklicken zum Binden bringen?
Aner eine letzte Waffe haben wir noch ... stelle die VBC mal auf EN um und teste damit.
Gib Bescheid ob sich was ändert.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
1 mal bearbeitet. Zuletzt am 01.01.2026 21:47 von RV.
mf_powerfly
2 January 2026 07:4302.01.2026 07:43
Good morning Rainer,
The problem persists even when the language is changed.
I upgraded the second stabilizer SN: 27010375 to VBar Professional V8 Firmware + Rescue Function.
After I plugged in the BEC battery (4 Eneloop cells), there was an electrical smell, but no blinking.
However, it could not be bound with the Express version either.
I also took the transmitter apart again to check if I had accidentally disconnected a cable during the Mode 1 conversion. But everything is fine.
Since I'm flying on vacation tomorrow, I suggest the following:
I'm opening a service ticket - 1xVBC - 2x VbarEVO
Put it in the shipping box, and where do I need to send it?
MIKADO Model Helicopters GmbH
Graf-von-Schwerin-Str. 40
DE 14469 Potsdam
Or is there a service depot?
I imagined switching to VBC would be easier. Nevertheless, thank you very much for the quick support and help. It's not a given that you get support over the New Year period!
Greetings from Austria
Mario
Guten Morgen Rainer,
das Problem bleibt auch bei umgestellter Sprache bestehen.
Ich habe das zweite Stabi SN: 27010375 auf VBar Professional V8 Firmware + Rescue Function upgegradet.
Nachdem ich den BEC Akku (4 Zellen Eneloop) ansteckte kam Elektrogeruch, kein blinken.
Hat sich aber mit der Express Version auch nicht binden lassen.
Habe auch den Sender nochmal auseinander geschraubt um nachzusehen ob ich nicht ein Kabel versehentlich abgzogen habe beim Mode 1 Umbau. Ist aber alles in Ordnung.
Da ich morgen in den Urlaub fliege schlage ich folgendes vor:
Ich eröffne ein Serviceticket - 1xVBC - 2x VbarEVO
Ab in den Versandkarton, und wohin muss ich das Versenden?
MIKADO Model Helicopters GmbH
Graf-von-Schwerin-Str. 40
DE 14469 Potsdam
oder gibt es ein Servicelager?
Hab mir den Umstieg auf VBC einfacher vorgestellt. Trotz all dem vielen Dank für die schnelle Unterstützung und Hilfe. Das ist nicht selbstverständlich, das man auch Support über den Jahreswechsel bekommt!
Grüsse aus Österreich
Mario
ulrich
2 January 2026 12:2902.01.2026 12:29
I think the cable to the radio module on the back has somehow slipped out. These components are usually very carefully inspected during manufacturing, but it seems it somehow came loose. We'll definitely look into it in our service department. The service ticket should contain all the necessary information on how to proceed.
So long... Uli
http://www.vstabi.de
Ich denke das das Kabel zum Funkmodul auf der Rückseite irgendwie rausgerutscht ist. Die Sachen werden ansich bei der Herstellung sehr sorgfältig geprüft, aber irgendwie ist es wohl rausgegangen. Das sehen wir uns im Service natürlich an. In dem Serviceticket sollte alles drinstehen wie genau vorzugehen ist.
so long ... Uli
http://www.vstabi.de
cc1975
2 January 2026 12:5502.01.2026 12:55
Perhaps the cable slipped out during the conversion to Mode 1... Maybe carefully unscrew the EVO+ again and check...
Eventuell ist das Kabel ja beim Umbauen auf Mode 1 rausgerutscht........... Eventuell vorsichtig die EVO+ nochmals aufschrauben und schauen......
RV
2 January 2026 13:5402.01.2026 13:54
The shipping address is correct - perhaps add "Mikado Service" as a second line.
I don't see a service message yet - has it already been created?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
2 mal bearbeitet. Zuletzt am 02.01.2026 13:56 von RV.
Die Versandadresse ist richtig - vielleicht noch "Mikado Service" als 2. Zeile einfügen.
Ich sehe noch keine Servicemeldung - ist diese schon erstellt?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
2 mal bearbeitet. Zuletzt am 02.01.2026 13:56 von RV.
Fingolf
2 January 2026 16:0402.01.2026 16:04
Just unscrew it again and check all the cables.
I also suspect it happened during the conversion to Mode 1.
Schraub einfach nochmal auf und prüfe alle Kabel.
Ich vermute auch dass es beim Umbau auf Mode 1 passiert ist.
mf_powerfly
2 January 2026 16:2602.01.2026 16:26
Hello Rainer,
I've just finished everything. I'm sending my entire order to the service center, as I'll be out of the country for 7 days starting tomorrow.
I've noted down Mikado Service.
Thank you!
Greetings
Mario
Hallo Rainer,
habe soeben alles erstellt. Schicke meine ganze Bestellung zum Service, da ich ab morgen für 7 Tage außer Landes bin.
Mikado Service hab ich notiert.
Vielen Dank!
Grüße
Mario
Eddi E. aus G.
5 January 2026 09:3505.01.2026 09:35
Hi and Happy New Year Mario,
I've seen the tickets. As soon as the package arrives, we'll take a look at it and get back to you.
Grüßle
Eddi
Born to fly ...
forced to work.
Moin und ein gutes Neues Mario,
ich habe die Tickets gesehen. Sobald das Paket da ist, schauen wir's uns an und melden uns dann darüber wieder.
Grüßle
Eddi
Born to fly ...
forced to work.