← VBar NEO/EVO VLink

8° at the four-blade head translated

VBar › VBar NEO/EVO VLink · Started by Stephan on 12 January 2026 18:0512.01.2026 18:05
Stephan 12 January 2026 18:0512.01.2026 18:05
I'm currently building my first helicopter with a four-blade rotor head. It will be a Roban MH-65 with HSM-800 mechanics. The swashplate is perfectly level at 0° pitch, but at 12° maximum pitch, the second servo is slightly off by 0.2-0.3°. However, the linkages can't be adjusted any further, and I don't think this will be a problem in scale flight.
As described in the "Scale Heli Setup Tips", I rotated the swashplate and set the return blade to 8°; that part was easy. Then I also measured the advance blade, and it's at about 10°.
Rainer, in your tips you write very specifically several times that the measurement should be taken on the returning leaf. Is that related?

Second question: The static twist isn't quite perfect, but it probably doesn't matter in the end. To familiarize myself with everything, I wanted to fine-tune the swashplate twist by 2-3° in the main rotor parameters. However, I can't seem to find that option in version 8.2. Is it no longer available?
machine-translated from German · Show original
RV 12 January 2026 21:2112.01.2026 21:21
So, whether it's forward or backward is irrelevant. It's always abs(8°) – so consider it without a sign.

Regarding the phasing – the fine-tuning in V7 was well-intentioned, but ultimately didn't make much of a difference and, after some testing, was unnecessary in V8. Therefore, adjust the TS (Torque Shift) in the setup. This can be done there with buttons in 5° increments, which is perfectly sufficient. Even smaller adjustments would be possible via direct input.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
Stephan 12 January 2026 22:3112.01.2026 22:31
As far as fine-tuning is concerned: all right, it was more of a game.

I may not have described my actual problem with the 8° measurement very well. I measure 8° above the tail boom, but about 10° above the nose. Is that normal?
machine-translated from German · Show original
RV 13 January 2026 07:2413.01.2026 07:24
OK - that now depends on the rotation (mechanical + electrical).

Since the Roban head already rotates on its own... you simply have to take the measurement at the point in the rotation where the angle of attack is greatest relative to the trim (zero position). So - place the helicopter on a level surface (it has to be in the water, the measurement is taken from the tail rotor, not the fuselage) - 0 degrees, setting 78°, highest point, adjust.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
Stephan 13 January 2026 21:1213.01.2026 21:12
Okay, I've done that. At the highest point I have 10° (= blade holder above the nose), at the lowest point 8° (= blade holder above the tail).

Then I did something else:
Cyclic ring adjusted so that max. cyclic deflections are 8° and then measured all around:

The leaf holder is on the right:
Nick forward -> 8°
Nick back -> 8°

The blade holder is located at the rear:
Roll left -> 8°
Roll right -> 8°

The leaf holder is on the left:
Nick forward -> 8°
Nick back -> 9°

Leaf holder is at the front:
Roll left -> 10°
Roll right -> 8°

:-/ :-/ :-/
machine-translated from German · Show original
RV 13 January 2026 22:1113.01.2026 22:11
Quote: I then did something else:
Cyclic ring adjusted so that max. cyclic deflections are 8° and then measured all around:

Did I write that? Probably not.

The CR limits the deflection. Nothing more. Like a car's floor pan limits full throttle. We adjust that too, so the floor pan doesn't bulge. But that has nothing to do with the 8° setting!

The 8° is a control variable so the control system knows how much is needed cyclically to produce a certain response. It's like a car where the driver knows that about half throttle is needed to reach 100 km/h. That's what we want to know here.

Quote: The page holder is on the right:
Nick forward -> 8°
Nick back -> 8°

The blade holder is located at the rear:
Roll left -> 8°
Roll right -> 8°

The leaf holder is on the left:
Nick forward -> 8°
Nick back -> 9°

Leaf holder is at the front:
Roll left -> 10°
Roll right -> 8°

Uhhh... and how was that determined? By checking the box for 8° in the setup?



Here's the order again:

- Setup
- Rotate the swashplate so that the 90° lead is there. That means when pitching forward, the blades move perpendicular to the direction of flight, but not parallel to it. Always leading, of course. This should work without rotation with the Roban head, which has the DFC rigid linkage with the unusual L-shaped levers, as far as I know.


Then continue here and set the temperature to 8°:
https://www.vstabi.info/de/node/2539

Keywords:
- TS teaching on leaf over stern
- Trim Tab (Condition: we have 0° - leaf folding method, possibly use this to work accurately if it is unclear whether it is 0°)
- While in the trim tab, pitch gauge on sheet zeros
- now measure and set 8°

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.




1 mal bearbeitet. Zuletzt am 13.01.2026 22:11 von RV.
machine-translated from German · Show original
Stephan 14 January 2026 14:3914.01.2026 14:39
In case you misunderstood: the confused emojis weren't directed at your statements, but at my measurements. I think I'm still not describing clearly enough what I'm doing and then observing.

Let me try a different approach. I proceed exactly as you describe from "Once again the sequence" onwards; the 8° are then set on the blade holder above the tail.

At this point, I deviate from the standard procedure: With the helicopters I've built so far, one with a 2-blade rotor head (and one with a 3-blade head), I've gotten into the habit of rotating the rotor head 180° afterward (while still in the 8° adjustment mode) to confirm that the 8° angle is also present in the position above the nose. Then I switch the swashplate gauge to the other blade holder and confirm again in both positions that the 8° angle is correct.
My rationale behind this measurement is simple: I believe it will help me find any undiscovered errors in upstream construction and adjustment steps. So far, however, it has always worked out.

This time, with this head, it's different: in 8° adjustment mode, 8° is set above the tail, a good value of 104 – check. Rotated the head 180° and the gauge reads 10° – huh? Repeated the measurement on the other three blade grips, same result. 8° above the tail, 10° above the nose. There must be a mistake somewhere, but where?

I don't use the CR to adjust anything. I understand that it's primarily intended for setting mechanical limits. I also understand that I need to use the 8° adjustment mode.

My thought process for troubleshooting: If I manually move the rotor to a specific cyclic angle, will I observe the same thing? In other words: will I measure different values on opposite sides of the rotor axis?

Therefore, I "misused" the CR (perhaps not legitimately?) and used its feature to stop at a defined angle when the stick is at full deflection. I believe I can easily reproduce a specific angle this way. It made sense to me to set this angle to 8° so that, ideally, I would get the same angle values as in the 8° setting mode.

In this test, I observed the same phenomenon as in the 8° setting mode. Roll-left (analogous to the 8° setting mode) results in 8° over the tail but 10° over the nose. Curiously, roll-right behaves differently: in both cases, 8° is applied over both the tail and nose. Furthermore, I observed the same phenomenon with pitch, specifically with the right/left position of the blade holder: with pitch forward, the value is the same on both sides, while with pitch aft, there is a difference.

Clearly, after the test, the CR returned to 65, where it should be initially. This wasn't a setting change, just an attempt at a reproducible measurement.

My suspicion after all the measurements: The linkages for servos 1 and 2 are slightly too long relative to servo 3. This might also explain what I measured at full pitch deflection (see first post): although the swashplate is at 0° all around at 0° pitch (trim position), at full pitch deflection, the deflection above servo 2 is only 11.7°, while everywhere else it's 12°. I had tolerated this, considering it minimal and not very relevant for scale flying. If this is the cause, I'm surprised that the difference between pitch and cyclic deflection is so significant (0.3° vs. 2°).

I'm basically just trying to confirm that there's an error and trying to rule out various possible causes.

The rotor head is different, by the way; it's no longer DFC-L lever-type, but rather a conventional, straight linkage. Since this post has gotten so long, I need a break. I'll write more about it later.

Thanks for your help!
machine-translated from German · Show original
Eddi E. aus G. 14 January 2026 15:5514.01.2026 15:55
Good morning,

There are so many measurement and other sources of error that I don't even want to go into it any further.

The method that always works for all helicopters is the one described by Rainer:

Ensure that all linkages above the swashplate are the same length.
Set the swashplate horizontally and to 0° in the setup/trim (a good eye is sufficient, fold the blades for 0°)
. Place the model 'in the water' (rotor shaft vertical)
If necessary, set a 90° lead angle and ensure proper alignment (multi-blade head and/or multi-point linkage if required by design).
. Leaf over the tail boom
Set it to 8° via the setup menu (sign doesn't matter).
. complete

The 8° is purely a calibration function, so that the VBar knows at which value 8° is present, from where it can operate.
And as a control function, if one had to set extremely high values (significantly above 100) or extremely low values (significantly below 70-60), it would indicate an unfavorable (bad ...) lever geometry.

Grüßle

Eddi

Born to fly ...
forced to work.



2 mal bearbeitet. Zuletzt am 14.01.2026 15:56 von Eddi E. aus G..
machine-translated from German · Show original
Stephan 14 January 2026 17:1914.01.2026 17:19
Hi Eddi,

Yes, of course, measurement error was my very first thought. But now I've started from scratch several times and measured again. If it were only a matter of a few tenths of a degree, I'd probably dismiss it. But the repeated 2° difference between the positions measured over the tail and over the nose, observed in several ways, is really giving me pause...

I adjusted it according to the procedure and got a value of 104 at 8° above the stern. If you tell me that's correct and I can ignore everything else, then great.

Just a quick note about the rotor head:
For some time now, Roban has stopped installing the DFC head and is instead using one with conventional linkages and a TS drive. The instructions are simply incorrect; the diagrams show the DFC head, but it's not actually installed, the information is contradictory, etc.

Attached is a picture (HSM-800 4-blade current) from the Bell 412 manual, where at least the head is shown.
The other image in the attachment (AS365 manual linkage rods) is an excerpt from the instructions for the AS365 I'm building. It states that the lengths should be set according to a diagram, with measurements to two decimal places, and then the next sentence says the lengths should be precisely 96 mm. That leaves room for interpretation...
I have currently set the lengths according to the scheme.
Previously, I had set it to 96 mm, which didn't work well. Looking at the bellcranks, etc., it seems plausible that at least the linkage for servo 1 (according to VBar's 120° swashplate numbering logic) must be slightly longer than the other two.
That was the case before too; with the old DFC head, servo 1 was 112 mm, the other two were 81 mm.

machine-translated from German · Show original
RV 14 January 2026 20:5414.01.2026 20:54
The high value of 104 seems familiar to me for Roban's current generation of mechanics. That should be correct.

However, you need to make sure you don't run out of travel (rotation angle) on the servo. The other users wanted to improve their "old" and overly aggressive linkage setup – but they went a bit overboard. So check if you have a reasonable cyclic deflection (visually, with swashplate) in all pitch positions, without it being blocked by the linkage being straight.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
Eddi E. aus G. 15 January 2026 09:3515.01.2026 09:35
Good morning,

Yes... and abandon the idea that the system shows exactly the same angle at every point all around; that only works under optimal conditions, and even then it's enough to make you tear your hair out.

The task is completed when the above conditions are met, and if the track alignment is also correct – it may be necessary to adjust individual linkages, and then possibly measure a 'wrong' angle somewhere in the circle.

At high values (104 seems perfectly OK to me), the addition also matters:
Example: 104 for 8°, 110 for pitch, (absurd) 70 trim on one servo, _can_ lead to the servo running out of travel, +/- 100% +/- 20-25% reserve for the ever-popular trim (just an example, there isn't even a standard...), then either the linkages bend too far in or out (Rainer's example), something mechanically breaks, or the servo stops at its end point, or, worse, becomes powerless because it can no longer do anything with the well-intentioned servo pulse.

But that wouldn't be any different without flybarless, rigid, directly controlled systems, if you overcompensate via limits, paths, and trim.

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
Stephan 15 January 2026 16:3815.01.2026 16:38
Rainer, when I looked at the linkages regarding "standing straight", I found the problem. :-)
The linkages from the bellcranks to the swashplate on servos 2 and 3 must be 35 mm long, not 38 mm...

I've corrected that. I haven't had enough time to properly set up the stabilizer yet; I need to do that properly. But the large difference between the tail and nose in the 8° setting mode is gone, at least with this quick and dirty fix. I expect to end up with a value around 100 here, and around 90 at 12° pitch. Trim values are <10. --> Perfect conditions.

I'm well within the limits of the servos, and the linkages too. I've tested everything at 12° pitch and 65 CR all around, and there's still an angle of >15° between the linkage and the lever arm, which I consider sufficient.
Negative pitch is a different story; less than -4°, possibly even only -3°, is not possible, otherwise the bellcrank of servo 1 will collide with the linkage between the servo and bellcrank at maximum cyclic deflections.

So, thank you so much for your support!
machine-translated from German · Show original
RV 15 January 2026 20:1215.01.2026 20:12
Quote: I'm well within the limits of the servos, and also the linkages. I've tested everything at 12° pitch and 65 CR all around, and there's still an angle >15° between the linkage and the lever arm, which I consider sufficient.
Negative pitch is a different story; less than -4°, possibly even only -3°, is not possible, otherwise the bellcrank of servo 1 will collide with the linkage between the servo and bellcrank at maximum cyclic deflections.

Yep - then that's ok, that's enough for an AR, nothing more is needed.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless