HelischuleGonzalez
1 February 2026 00:0501.02.2026 00:05
Hello Mikado team,
I wanted to ask what bit resolution the Evos have on the swashplate and tail at 125 and 250 center pulse? 12 bits, like the Hall gimbals?
Background: I will soon be getting servos that can handle 125mm servos at 2000Hz or 250mm servos at 1000Hz.
Evo offers me 250s with 1000Hz on the swashplate and 125s with up to 2000Hz at the tail.
If the servos are perfectly capable of this, can I expect smooth operation if I set 250 servos at 1000Hz with an 8.2 TS algorithm on the swashplate and 125 servos at 1000Hz or even 2000Hz on the tail?
Thank you for the information,
Daniel from the Gonzalez Helicopter School
Hallo Mikadoteam,
wollte fragen, wie viel Bit Auflösung die Evos an der Taumelscheibe und am Heck haben bei 125er und 250er Mittenimpuls? 12Bits, so wie die Hall-Gimbals?
Hintergrund ich bekomme bald Servos, die 125er mit 2000 Hz oder 250er mit 1000Hz können.
Evo bietet mir ja 250er mit 1000Hz an der Taumelscheibe an und 125er mit bis 2000Hz am Heck.
Wenn die Servos das perfekt können, kann ich da einen reibungslosen Betrieb erwarten, wenn ich an der Taumelscheibe 250er mit 1000Hz mit 8.2 TS Algorithmus einstelle und am Heck 125er mit 1000Hz oder gar 2000 Hz?
Vielen Dank für die Infos,
Daniel von der Helischule Gonzalez
HelischuleGonzalez
2 February 2026 10:2302.02.2026 10:23
And one more question. Should I set and operate the servo on the tail at Dshot 300, even though it only has 11 bits, or would higher performance be expected with a 125 or 250 center pulse?
One more question. Is it better to use a 760 mid-range impulse and 500 Hz or a 250 mid-range impulse with 1000 Hz using TS algorithm 8.2?
As you know, I'm not a fan of TS algorithm 8.2 with a 1500 center pulse, however, 8.2 is very good with 760 and 333Hz.
My new servo can even handle 760s at 1000 Hz, hence the choice between 760s at 333 Hz or 500 Hz or 250s at 1000 Hz.
Und noch eine weitere Frage. Soll ich das Servo auf dem Heck lieber auf Dshot 300 einstellen und betreiben, auch wenn es nur 11 bits hat oder wäre mit 125er oder 250er Mittenimpuls eine höhere Performance zu erwarten?
Noch eine Frage. Besser 760er Mittenimpuls und 500 Hz oder 250er mit 1000 Hz mit TS Algorithmus 8.2?
Wie ihr wisst bin ich ja kein Fan von TS Algorithmus 8.2 mit 1500er Mittenimpuls, allerdings ist 8.2 sehr gut mit 760er und 333hz.
Mein neues Servo kann sogar 760er mit 1000 hz, daher eben die Auswahl 760er mit 333hz oder 500 Hz oder 250er mit 1000 Hz.
ulrich
5 February 2026 00:2905.02.2026 00:29
The resolution is 12 bits in every PPM configuration, even with the narrower pulses. The timers have a much higher resolution. 12 bits at 760µs is 185 nanoseconds -- okay ;-) . DShot - I don't know about servos. It's actually designed for motors, because there are special codes for programming and "motor off," for example. That reduces the resolution even further.
I haven't tested anything like that yet, so I can't say much about the results; technically, it's not relevant in my opinion. The play and dead times of the servos are much more important.
Regarding frequencies, it's more about how the system performs overall. The absolute value isn't relevant; rather, it's the control characteristics of the respective servos that matter. Such high rates are an interesting experiment.
So long... Uli
http://www.vstabi.de
Die Auflösung ist in jeder PPM Config 12 Bit, auch bei den schmaleren Pulsen noch. Die Timer lösen viel höher auf. 12 bit bei 760uS sind 185 Nanosekunden -- na gut ;-) . DShot - weiss nicht für Servos. Das ist eigentlich für Motoren designt, denn da gibts z.B. spezielle Codes zum Programmieren und "Motor Aus" Das geht noch von der Auflösung ab.
Ich hab sowas noch nicht getestet, daher kann ich nicht viel zu den Ergebnissen sagen; technisch ist das mMn nicht relevant. Das Spiel und die Totzeiten der Servos sind da viel wichtiger.
Bei den Frequenzen kommt es ebenfalls eher darauf an wie das System insgesamt spielt. Der absolute Wert ist nicht relevant. Eher die Regeleigenschaften der entsprechenden Servos. So hohe Raten sind eine interessante Spielerei.
so long ... Uli
http://www.vstabi.de
HelischuleGonzalez
5 February 2026 18:0805.02.2026 18:08
Hi Uli,
So you see no danger in trying out the 250 mid-range pulse on the TS, right?
DShot should offer some advantages on the rear due to its digital protocol, since it's somewhat faster, but above all more precise, right?
Off the top of your head, would you rather use a 250, 125 or Dshot servo on the tail servo?
The servos will be the AEON T40 from Xguard. They can even handle Dshot at 9000 Hz perfectly.
Best regards,
Daniel
Hallo Uli,
Du siehst also zumindest keine Gefahr den 250er Mittenimpuls auf der TS auszuprobieren, richtig?
Dshot müsste ja durch das digitale Protokoll aber auf dem Heck durchaus etwas bringen,.da es ja etwas schneller ist, aber vor allem präziser, oder?
Aus dem Bauch heraus, würdest Du auf dem Heckservo eher 250er, 125er oder Dshot nehmen?
Servos werden es übrigens die AEON T40 von Xguard. Die können sogar Dshot mit 9000 Hz wunderbar ab.
LG,
Daniel
ulrich
6 February 2026 18:2906.02.2026 18:29
Trying is always good; I don't see what dangers might arise from it.
Dshot does have slightly lower resolution, but that's probably not relevant. The rates a servo can handle are pretty much irrelevant, because what the servo actually does with those rates isn't reflected in the number.
We don't control the motor directly, but rather an internal servo control loop that then controls the mechanics. Therefore, the parameterization of the servo's own control loop and its filters is 1000 times more important than the raw control rate.
So long... Uli
http://www.vstabi.de
Probieren ist immer gut, ich wüsste nicht welche Gefahren dadurch bestehen sollten.
Dshot löst halt etwas weniger auf, aber relevant ist das wohl eher nicht. Die Raten die ein Servo abkann sind wirklich ziemlich irrelevant, denn was das Servo damit macht, ist in der Zahl nicht enthalten.
Wir steuern ja nicht den Motor direkt, sondern immer einen servointernen Regelkreis, der dann die Mechanik steuert. Daher ist die Parametrierung des Servoeigenen Regelkreises und dessen Filter 1000mal wichtiger als die nackte Ansteuerrate.
so long ... Uli
http://www.vstabi.de
HelischuleGonzalez
7 February 2026 11:5907.02.2026 11:59
The best example is the BK 8005 tail servo :-)
Even by today's standards, it's ridiculously fast and quite powerful, but the performance was abysmal, and that of a BLS 251 at 4.8V was worlds better.
Then I'll just test everything as soon as I have the servos. DShot seems to have an advantage despite being 11-bit.
Gemini's comment on this is as follows:
Here is a direct comparison between DShot (11 bit) and 760µs Analog (12 bit) at 1000Hz each:
DShot (Digital)
?Advantages:
Zero jitter: No signal distortion due to EMC interference or cable lengths.
No calibration required: The zero point and end positions are digitally defined.
Latency: No conversion losses (ADC/DAC); the command is processed immediately as a packet.
?Disadvantages:
Lower resolution: With 11 bits, "only" 2048 steps compared to 4096 with 12 bits.
?760µs / 125µs / 250µs (Analog/PWM)
?Advantages:
Higher theoretical resolution: 12 bits offer finer gradations (4096 steps), which is theoretically more precise with extremely long servo arms.
?Disadvantages:
Susceptibility to interference: Analog pulses can vary minimally due to induction (signal noise).
Computational effort: The servo has to constantly measure and average the pulse length, which creates minimal delays.
Conclusion: DShot's digital integrity almost always outweighs the advantage of 12-bit resolution during flight. In practice, you'll notice the more stable signal quality more clearly than the doubled step count, since the mechanics are usually the weakest link.
Bestes Beispiel ist da das BK 8005 Heckservo :-)
Selbst nach heutigem Stand abartig schnell, recht kräftig, aber Performance war unterirdisch und die eines BLS 251 an 4,8V um Weeeeelten besser ^^
Dann werde ich einfach mal alles testen, sobald ich die Servos habe. Dshot scheint trotz 11Bit im Vorteil zu sein.
Gemini meint dazu folgendes:
Hier ist der direkte Vergleich zwischen DShot (11 Bit) und 760µs Analog (12 Bit) bei jeweils 1000Hz:
?DShot (Digital)
?Vorteile:
?Null Jitter: Keine Signalverfälschung durch EMV-Störungen oder Kabellängen.
?Keine Kalibrierung: Der Nullpunkt und die Endwege sind digital fest definiert.
?Latenz: Keine Wandlungsverluste (ADC/DAC); der Befehl wird als Paket sofort verarbeitet.
?Nachteile:
?Geringere Auflösung: Mit 11 Bit "nur" 2048 Schritte gegenüber 4096 bei 12 Bit.
?760µs / 125µs / 250µs (Analog/PWM)
?Vorteile:
?Höhere theoretische Auflösung: 12 Bit bieten feinere Abstufungen (4096 Schritte), was bei extrem langen Servohebeln theoretisch präziser ist.
?Nachteile:
?Störanfälligkeit: Analoge Pulse können durch Induktion minimal variieren (Signalrauschen).
?Rechenaufwand: Das Servo muss die Pulslänge ständig messen und mitteln, was minimale Verzögerungen erzeugt.
?Fazit: Die digitale Integrität von DShot überwiegt im Flug fast immer den Vorteil der 12-Bit-Auflösung. In der Praxis spürst du die stabilere Signalqualität deutlicher als die doppelte Schrittanzahl, da die Mechanik meist das schwächste Glied ist.