← VBar NEO/EVO VLink

Vbar Neo loses connection translated

VBar › VBar NEO/EVO VLink · Started by smtjets on 23 February 2026 12:3023.02.2026 12:30
smtjets 23 February 2026 12:3023.02.2026 12:30
Hello everyone,

I bought a used, crash-free Vbar Neo #20042189 with a rescue package.
Unfortunately, the Neo loses connection when subjected to moderate blows to the back of the head (V), regardless of whether the transmitter is right next to the Neo or 10m or more away.
The previous owner repeatedly confirms that he flew the aircraft until recently, which is quite conceivable.
However, I have my doubts about its crash-free design.


Here you can see my Vbar Neo stress test; the Neo was supposed to work in a turbine helicopter after the tests, but that probably won't happen.

https://www.youtube.com/shorts/TcojsU6u-5o

The pictures show the antenna feedthrough (0001.jpg (only the top one)), the aluminum housing looks flawless.

I was able to reproduce the error several times. I suspect the Neo crashed and the MCU might have a loose solder joint; all other components look okay.

Should I throw it away or send it in?
Was this serial number sold in an aluminum or plastic housing?
Can purchased packages be transferred to another identical device if the old serial number is deactivated?

Thank you for your help

Greetings, Markus

machine-translated from German · Show original
Eddi E. aus G. 23 February 2026 13:5823.02.2026 13:58
Hi Markus,

Yes, something might be loose, or a conductor track or via in the 6-layer circuit board might be cracked, or something might be sparking.
You could possibly read the log with your PC; there might be more information in there. From the transmitter's perspective, it looks like it's switched off.

In any case, it's uncertain.

It seems that this VBar was not purchased directly from us, so I cannot say whether it was factory-made in aluminum or modified later.
The serial number has not appeared in our service department since then, so I can't say anything more about it.

The antenna feedthrough may chafe, even if only minimally, meaning signs of wear are possible (but not serious).
It's hard to say what that 'gritty' stuff is. Just plastic abrasion?

Ultimately, it's a plastic part that's also good for clamping/fixing the circuit board.

-> When in doubt, throw it away. For safety reasons.
-> Please send another email (service (at) mikado-heli (dot) de) or create a service case, then we can see what we can do with the update.

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
smtjets 23 February 2026 17:5723.02.2026 17:57
Hi Eddi,

The grit is hard, possibly CA adhesive; cracks are also visible.

I caused another crash with the following messages in the PC log:
It's strange that there's no longer a connection to the transmitter after the failsafe.

What I forgot to mention is that the circuit board was loose inside the housing; this was very noticeable when moving the housing.
I heard I glued the circuit board in place with 4 mini adhesive dots.

Thank you so much Eddi for your help

Regards, Markus


PC LOG
OK 15:24 Everything is fine (10 sec)
Info 15:32 Increased vibration level
Info 15:41 Increased vibration level
OK 15:51 Everything is OK (10 sec)
Info 16:00 Increased vibration level
OK 16:10 Everything is OK (10 sec)
Info 16:18 Increased vibration level
Warning 16:26 RC input package lost
Critical 16:26 RC Falisave was activated
Info 16:27 Increased vibration level
Info 16:37 Increased vibration level
OK 16:47 Everything is fine (10 sec)
OK 16:57 Everything is fine (10 sec)
OK 17:07 Everything is OK (10 sec)
OK 17:17 Everything is OK (10 sec)
machine-translated from German · Show original
Eddi E. aus G. 24 February 2026 11:3324.02.2026 11:33
Good morning,

It's strange that there's no longer a connection to the transmitter after the failsafe.

...well, if something's broken, a loose connection, ...it might reconnect if you press in the right spot, but that's not practical ^^

The circuit boards are normally clamped in the housing so that they cannot—or should not—move.
Due to manufacturing tolerances in the circuit boards (not so much in the housings), compensation may be necessary; this is usually done longitudinally by the antenna feedthrough (with its wedge-shaped nubs), and during assembly a thin adhesive pad may be placed underneath to vertically clamp/fix the angled circuit board (servo connector).

Someone may have correctly noticed that the circuit board has play and tried to fix it with CA.

You see these kinds of makeshift solutions 'everywhere', by the way: 3D-printed rubber, adhesive tape, potting compound, clamping tabs... all perfectly legitimate :-)

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
smtjets 24 February 2026 16:2824.02.2026 16:28
Hello,
Yes, at least I now have a €205 aluminum case for an EVO....

under your motto
Born to fly...
and not forced to work!

It also works with that weird pole!
Finally, flying weather again!

Greetings from sunny Alsace

Markus

machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless