Hello Mikado Team,
I flew in my M7R today and now I have a few questions.
The following components are installed:
VBAR EVO 8.1
Swashplate: KST HLS3008
Rear KST HST1535
YGE Aureus 185 and XNOVA ligning 4525 / 480kv
1. I currently have the swashplate frequency set to 250 Hz; the servos can handle up to 500 Hz. Does it make sense to set a higher frequency directly and then continue testing the settings? Or should I adjust the settings first and then increase the frequency? Or will the higher frequency not make much of a difference?
2. I'm experiencing slight pitching on short input impulses. I've already reduced the direct portion. What's the best way to proceed? I've also increased the stop-loss level somewhat.
3. A particularly noticeable feature at the moment is a rocking motion on the pitch when the helicopter comes out of a loop.
What would be the best option?
I'm attaching the setup.
I flew and set it up in Bank 2 (rotation speed approx. 1600 rpm)
Thank you so much for your help.
Best regards
Stefan
I flew in my M7R today and now I have a few questions.
The following components are installed:
VBAR EVO 8.1
Swashplate: KST HLS3008
Rear KST HST1535
YGE Aureus 185 and XNOVA ligning 4525 / 480kv
1. I currently have the swashplate frequency set to 250 Hz; the servos can handle up to 500 Hz. Does it make sense to set a higher frequency directly and then continue testing the settings? Or should I adjust the settings first and then increase the frequency? Or will the higher frequency not make much of a difference?
2. I'm experiencing slight pitching on short input impulses. I've already reduced the direct portion. What's the best way to proceed? I've also increased the stop-loss level somewhat.
3. A particularly noticeable feature at the moment is a rocking motion on the pitch when the helicopter comes out of a loop.
What would be the best option?
I'm attaching the setup.
I flew and set it up in Bank 2 (rotation speed approx. 1600 rpm)
Thank you so much for your help.
Best regards
Stefan
Hallo Mikado Team,
ich hab e heute meinen M7R eingeflogen und habe jetzt noch ein paar Fragen.
Folgende Kompnenten sind verbaut:
VBAR EVO 8.1
Taumelscheibe: KST HLS3008
Heck KST HST1535
YGE Aureus 185 und XNOVA ligning 4525 / 480kv
1. Im Moment habe ich 250 Hz Taumelscheibenfreuquenz eingestellt; Die Servos können bis 500 HZ. Macht es Sinn direkt höhere Frequenz einzustellen um dann weiter mit den Einstellungen zu testen? Oder erst weiter einstellen und dann Frequenz erhöhen. Oder bringt die höhere Fequenz nicht viel?
2. Ich habe leichtes nachwippen auf Nick bei kurzen Eingabeimpulsen. Direkt Anteil habe ich schon reduziert. Wie sollte ich am besten weiter vorgehen? Die Stopunterstützung habe ich auch schon etwas erhöht.
3. Besonders auffällig ist im Moment ein Wippen auf Nick wenn der Heli aus einem Looping raus kommt.
Was wäre da die beste Option.
Ich hänge mal das setup an.
Geflogen und eingestellt habe ich in Bank2 (Drehzahl ca. 1600 U/min)
Vielen Dank für die Hilfe.
Viele Grüße
Stefan
ich hab e heute meinen M7R eingeflogen und habe jetzt noch ein paar Fragen.
Folgende Kompnenten sind verbaut:
VBAR EVO 8.1
Taumelscheibe: KST HLS3008
Heck KST HST1535
YGE Aureus 185 und XNOVA ligning 4525 / 480kv
1. Im Moment habe ich 250 Hz Taumelscheibenfreuquenz eingestellt; Die Servos können bis 500 HZ. Macht es Sinn direkt höhere Frequenz einzustellen um dann weiter mit den Einstellungen zu testen? Oder erst weiter einstellen und dann Frequenz erhöhen. Oder bringt die höhere Fequenz nicht viel?
2. Ich habe leichtes nachwippen auf Nick bei kurzen Eingabeimpulsen. Direkt Anteil habe ich schon reduziert. Wie sollte ich am besten weiter vorgehen? Die Stopunterstützung habe ich auch schon etwas erhöht.
3. Besonders auffällig ist im Moment ein Wippen auf Nick wenn der Heli aus einem Looping raus kommt.
Was wäre da die beste Option.
Ich hänge mal das setup an.
Geflogen und eingestellt habe ich in Bank2 (Drehzahl ca. 1600 U/min)
Vielen Dank für die Hilfe.
Viele Grüße
Stefan
machine-translated from German · Show original