← VBar NEO/EVO VLink

VBar EVO RX-Only Satellite Receiver translated

VBar › VBar NEO/EVO VLink · Started by Rolf Rakette on 3 November 2025 18:3603.11.2025 18:36
Rolf Rakette 3 November 2025 18:3603.11.2025 18:36
Good evening,

This item is new in the shop.

Did I understand correctly that this is a receiver antenna extension?

It seems to me that this is a replacement if you don't want to connect a basic antenna to the stabilizer.

Or rather, no additional channels are needed.

Or can servos be attached to this part?

I think the idea is great!

Greetings
Rolf
machine-translated from German · Show original
RV 3 November 2025 18:4103.11.2025 18:41
This is purely a receiving satellite.

It is not a replacement for Slave-NEO/EVO if you actually need the slave outputs.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.




1 mal bearbeitet. Zuletzt am 03.11.2025 18:42 von RV.
machine-translated from German · Show original
JMalberg 3 November 2025 18:4203.11.2025 18:42
Ah, there he is at last! Yay!

@Rakette: This is an additional receiver that can be installed as a satellite, especially in large models.

Edith: Rainer was faster

Regards, Jürgen
(Here are the missing commas for free use in my posts: ,,,,,,,,, )



Edited once. Last edited on 03/11/2025 at 18:42 by JMalberg.
machine-translated from German · Show original
Rolf Rakette 3 November 2025 18:4903.11.2025 18:49
RV wrote:
-------------------------------------------------------
This is purely a receiving satellite.
>
It is not a replacement for the Slave NEO/EVO if you consider the
Slave outputs are needed after all.


So, if I understand correctly, it only adds more antennas, not channels or outputs.

If you need more channels, then it's the same as before with the Basic one.

Greetings and thank you

Rolf
machine-translated from German · Show original
Eddi E. aus G. 4 November 2025 09:2604.11.2025 09:26
Korrektamundo.

If I need more connections (or have a VBar NEO), VBasic (single-brand, meaning EVO to EVO or NEO to NEO) with extender firmware, if I (only) want a remote satellite, then that's the one.
From a radio technology perspective, this is also smarter than installing longer antennas so that they might just barely 'stick out' of the fuselage.

Please do not confuse this with the VBar Control Satellite 04882, which can be used as a receiver (without servo connections) for VBar non VLink (without antennas, not convertible) or old Mini VBar or those with external sensor, black/Blueline/Silverline.

The RX-Only Satellite only works with the VBar EVO.

Greetings

Edd

Born to fly ...
forced to work.
machine-translated from German · Show original
Rolf Rakette 10 November 2025 18:5010.11.2025 18:50
Good evening Eddi,

I have now decided on the EVO V7 plus this RX-only satellite receiver.

Unfortunately, it was already sold out where you were... :-)

I ordered the item plus the other thing I wanted to order from Austria again :-)

One more question about the satellite.

Does something need to be activated in the EVO V7, or will the two recognize each other automatically?

What if you plug it into AUX3?

Greetings and have a nice evening
Rolf
machine-translated from German · Show original
RV 10 November 2025 20:2110.11.2025 20:21
As always in a master-slave setup, you have to activate the Interbus on AUX3 in the MC settings and restart once.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
Eddi E. aus G. 11 November 2025 09:0611.11.2025 09:06
Good morning,

You can also read about it here :-)

—Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
Rolf Rakette 16 November 2025 14:1816.11.2025 14:18
RV wrote:
-------------------------------------------------------
As always in a master-slave system, one must
> In the MC settings, connect the Interbus to AUX3
Activate and restart once.


Hello Rainer,

The package from Austria arrived yesterday :-)

The EVO v7 looks great, including the new USB cable port for registration.

I almost wouldn't have found the satellite if it hadn't been sealed in such large bags. :-)

Today I registered the EVO and immediately upgraded to Pro.

It took a long time because somehow I couldn't access my account....

Yeah, well, internet and stuff... >:-(

Once that was done, following the instructions in EVO, AUX2+3 were switched accordingly.

The dwarf is infected and also appears.

One more question: why does Aux2+3 need to be rearranged?

I thought with the EVO only one AUX channel would be used to connect a second one or the dwarf device.

In the selection menu, I could only choose AUX2+Aux3. Is something additional required?

I think Aux2 shouldn't be usable as a channel anymore, right?

Is there an explanation or reason for this? :-(

Greetings and thank you in advance for your reply.

Rolf
machine-translated from German · Show original
ulrich 16 November 2025 14:5216.11.2025 14:52
It's only the AUX3 channel. Previously (NEO), both were used; the new EVO Interbus only needs one. Therefore, it's still listed that way for historical reasons; the Macrocells app is the same for EVO and NEO.

Aux2 can be used normally.

So long... Uli
http://www.vstabi.de
machine-translated from German · Show original
PMDirk 16 November 2025 16:5316.11.2025 16:53
Hello everyone,

I also have a question about the EVO RX satellite receiver.
Can I extend the satellite connection cable?

Regards, Dirk
machine-translated from German · Show original
Rolf Rakette 16 November 2025 16:5616.11.2025 16:56
Hi Uli,

Thank you so much for the information :-)

Incidentally, this is not meant to be a criticism of the satellite; it just seems so small.

But why is the connection so short, or why is there a servo connector attached?

The cable is the same size as telemetry cables.

Wasn't there something smaller available?

I'm thinking of scalers; now the satellite is barely visible, but the connection is.

Because the counterpart to the servo plug needs to be secured as well.

Just an idea: what if you added one or two more telemetry connection sockets to the Evo board?

and if the satellite were connected via such a connection, then the connections would be much smaller.

And all the aux ports on the EVO would be free... But that would mean the layout of the circuit board would change.

what to change and the casing....

Greetings
Rolf
machine-translated from German · Show original
RV 16 November 2025 20:0916.11.2025 20:09
Quote: Can I extend the satellite connection cable?


The enclosed instructions state a maximum of 1m - so yes.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
thomas1130 16 November 2025 20:2216.11.2025 20:22
It would be great to have something that size with only one connector – and that outputs S-BUS, for example – without a gyro – so a tiny receiver only with just one digital output – that would be really interesting :-)

LG



Edited once. Last edited on 16/11/2025 at 20:22 by thomas1130.
machine-translated from German · Show original
steveman 28 December 2025 12:4728.12.2025 12:47
That's something I'd be looking for too.
machine-translated from German · Show original
RV 28 December 2025 20:3628.12.2025 20:36
There's something in the pipeline that meets your needs... as the drums say ;-)

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
MarcoWeh 17 March 2026 22:0917.03.2026 22:09
Good evening,

Any news on what will be released from the pipeline and when? :-)


Greetings Marco
machine-translated from German · Show original
RV 17 March 2026 22:2517.03.2026 22:25
https://www.vstabi.info/forum/read.php?57,209269,210028#msg-210028

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless