thomas1130
25 March 2026 16:5725.03.2026 16:57
Hi everyone,
One of my favorite helicopters exhibits a strange behavior in flight when pitching - at high rotation rates it very rarely "pauses" for a fraction of a second - and then continues...
Upon closer inspection, I noticed that one of the servos in the TS (turbocharger) seems to be running a little too far - and then becoming "powerless" - only to "catch" itself again later.
Otherwise, it flies great...
Is there a way to slightly reduce the maximum end deflection of a single TS servo?
Or would it be better to completely limit the swashplate ring?
I just tested it - if I go from the normal 85 to exactly 66 on the cyclic ring, then the pitch servo no longer enters the "critical range" - and remains stable.
To what extent would a value of 66 be "okay"? - Does it also limit the normal rotation rate - or does it only affect the extreme positions?
Because I don't actually want to change the maximum rotation rate - it's perfect as it is.
Mechanically, this is not a problem - the TS has enough space - there is no start-up.
Or buy a new servo set?
Or any other ideas?
Perhaps make the servo arms longer? - then I'd need less deflection, but lose power?
Hmm..
Thanks.
Best regards,
Thomas
Edited 4 times. Last edited on 25.03.2026 at 18:49 by thomas1130.
Hi allerseits,
einer meiner Lieblingshelis zeigt im Flug ein merkwürdiges Verhalten auf Nick - bei starker Drehrate "pausiert" er sehr selten für den Bruchteil einer Sekunde - und macht dann wieder weiter..
Bei näherer Inspektion habe ich festgestellt, dass ein Servo der TS wohl ein klein wenig zu weit läuft - und dann "kraftlos" wird - um sich dann später wieder zu "fangen".
Ansonsten fliegt er topp...
Gibt es eine Möglichkeit, ein bei einem einzelnen TS Servo den max Endausschlag ein wenig zu reduzieren?
Oder besser den Taumelscheibenring komplett begrenzen?
Ich habe es gerade getestet - wenn ich von den normalen 85 auf genau 66 beim cyclic ring gehe, dann kommt das nick Servo nicht mehr in den "kritischen Bereich" - und bleibt stabil.
Inwieweit wäre ein Wert von 66 "ok"? - begrenzt mir der auch die normale Drehrate - oder wirkt der nur auf die Extrempositionen?
Denn ich mag aber eigentlich die maximale Drehrate nicht verändern - die ist perfekt so wie sie ist..
Mechanisch ist das kein Problem - die TS hat genug Raum - es gibt kein anlaufen.
Oder neuen Servosatz kaufen?
oder andere Ideen?
Vielleicht die Servoarme länger machen? - dann brauch ich weniger Ausschlag, verliere aber Kraft?
Hmm..
Danke.
LG,
Thomas
4 mal bearbeitet. Zuletzt am 25.03.2026 18:49 von thomas1130.
ulrich
25 March 2026 18:4925.03.2026 18:49
Also check the trim. Sometimes you can move the servo one tooth further and correct it with the trim. Then you'll have the full range of motion. Of course, it shouldn't "fall off" on the other side.
So long... Uli
http://www.vstabi.de
Check auch mal die Trimmung. Manchmal kann man das Servo einen Zahn weiter hängen, und mit der Trimmung korrigieren. Dan hat man den vollen Weg. Darf natürlich dann nicht auf der anderen Seite "herunterfallen".
so long ... Uli
http://www.vstabi.de
thomas1130
25 March 2026 18:5225.03.2026 18:52
Thanks Uli - that's a good point, since the problem only occurs on one side of the path.
Of course - Murphy's Law - the servo is the most difficult to access... :-/
But they're predicting 3 days of rain anyway - so I'll expand on that and change one tooth...
Thanks!
LG
Thomas
Danke Uli - das ist ein guter Gedanke, da das Problem NUR auf einer Seite des Weges auftritt..
Natürlich - Murphys Law - das Servo, wo man am kompliziertesten ran kommt.. :-/
Aber es kommen hier eh 3 Tage Regen angeblich - da werde ich das mal ausbauen und einen Zahn ändern..
THX!
LG
Thomas
thomas1130
25 March 2026 20:4825.03.2026 20:48
Trim was set to -48...
I moved the lever one tooth – then set the trim to +20 – unfortunately, the problem has now shifted to the other direction of rotation... :-(
It's likely to be a very tight squeeze.
Are "old" JR servos (SLS01) - actually great - but completely powerless in the end position... - why is that?
Next, I'll try using the servo arm with one hole longer - let's see...
Otherwise, I'll just have to get new servos, because I absolutely don't want to compromise on the rotation rate. :-)
Best regards,
Thomas
Trimmung war auf -48...
Habe den Hebel um einen Zahn ungehängt - darauf Trimmung bei +20 - leider hat sich das Problem jetzt auf die andere Laufrichtung verschoben.. :-(
Dürfte alles sehr knapp sein..
Sind "alte" JR Servos (SLS01) - eigentlich topp - aber in der Endstellung komplett kraftlos.. - wieso ist das eigentlich so?
Als nächstes probiere ich den Servohebel um ein Loch länger zu verwenden - mal schauen..
Ansonsten müssen halt neue Servos her, denn einen Kompromiss bei der Drehrate will ich keinesfalls machen. :-)
LG,
Thomas
RV
25 March 2026 22:0025.03.2026 22:00
Yeah - that's the thing, some servo manufacturers define a (too narrow) pulse range for validity. Instead of using the "last valid" pulse, they then become weak. Tough luck. There's no standard for this. It's a toy ;-)
Therefore, use different servos if the definition is too narrow, or limit the range with "less pitch and less CR".
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
1 mal bearbeitet. Zuletzt am 25.03.2026 22:01 von RV.
Jou - das ist so dass manche Servo Hersteller einen (zu engen) Pulsbereich der Gültigkeit definieren. Anstelle "last valid" zu nehmen werden sie dann kraftlos. Pech. Hier gibts halt keine Norm. Ist Spielzeug ;-)
Insofern - andere Servos nehmen wenn die Definition zu eng ist oder Wege mit "weniger Pitch und weniger CR" begrenzen.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
1 mal bearbeitet. Zuletzt am 25.03.2026 22:01 von RV.
Bernd S.
26 March 2026 05:4726.03.2026 05:47
Wasn't there something about the control frequency that, if the values are unsuitable, causes the servos to become weak at the end of their travel?
Just a reminder of the configs of an ignorant person... .
But perhaps there's still room for optimization?
Regards, Bernd
War da nicht noch was mit Ansteuerfrequenz was bei unpassenden Werten die Servos im Endbereich kraftlos werden lässt ?
Nur so eine Erinnerung an die Configs eines Unwissenden... .
Aber evt. kann man da noch was optimieren ?
Gruß Bernd
RV
26 March 2026 07:0626.03.2026 07:06
Nope. It's the pulse length – if that's completely off, you get the same effect much earlier, and it won't work at all except at a complete stop.
So please don't confuse yourselves here.
We're quite familiar with this effect here; years ago, a team pilot at the IRCHA noticed a sudden stall in flight with two otherwise identical helicopters... also equipped with JR servos... that's just how it is. Bad luck.
There's nothing to optimize here except that the servo manufacturer needs to rethink the behavior of the servo firmware. It's simply set too narrowly, and having no power is the worst option if you previously had a valid signal and signals are still coming in – but they're "a bit too strong." However, having no power would be good in the event of a signal loss.
=> Longer servo arms (accepting reduced force and resolution) or lower pitch and CR if adjusting the servo arm (center, trim offset) doesn't help. If you don't want to do that => different servos.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
1 mal bearbeitet. Zuletzt am 26.03.2026 07:07 von RV.
Nope. Die Pulslänge ist es - wenn die gar nicht stimmt hat man denselben Effekt aber schon viel früher und es geht gar nicht mehr außer an einem Endanaschlag.
Also - verwirrt Euch hier bitte nicht.
Wir kennen den Effekt hier recht gut, da hatte vor zig Jahren ein Teampilot auf der IRCHA bei 2 an sich identischen Helis im Flug ein Ausbrechen bemerkt ... auch JR Servos ... isso. Pech.
Da gibts nix zu optimieren außer dass der Servohersteller sein Verhalten der Servo Firmware hier überdenken muss. Das ist einfach zu eng gesetzt und kraftlos ist auch noch die schlechteste Option wenn man vorher ein gültiges Signal hatte und weiterhin Signale kommen - aber eben "was drüber" sind. Bei Signalausfall wäre es aber hingegen gut kraftlos zu sein.
=> längere Hebel (unter Inkaufnahme einer schlechteren Kraft und Auflösung) bzw. Pitch und CR runter wenn Servohebel (Mitte, Trim Offset) versetzen nix hilft. Möchte man das nicht => andere Servos.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
1 mal bearbeitet. Zuletzt am 26.03.2026 07:07 von RV.
Eddi E. aus G.
26 March 2026 09:2126.03.2026 09:21
Good morning,
What do the values look like? Do you perhaps have the setup in your cloud so we can take a look?
As Rainer already writes, it is the addition that can drive the pulse over the limit: high value for +/– pitch, high value for 8° cyclic, trim, high maneuverability.
The CR can help, although I wouldn't want values below 70, as that already limits the maneuverability on one axis.
Below age 66, I believe the trim flight would no longer be active; there used to be something like that.
But perhaps it's possible to get just below the threshold (or slack value? Slack value?) mechanically or even just through a minor adjustment.
Grüßle
Eddi
Born to fly ...
forced to work.
Moin,
wie sehen denn die Werte aus, hast Du das Setup ggfs. in Deiner Cloud so dass wir mal schauen können?
Wie Rainer schon schreibt ist es die Addition, die den Puls über's Limit treiben kann, hoher Wert für +/– Pitch, hoher Wert für 8° zyklisch, Trimmung, hohe Wendigkeit.
Der CR kann helfen, wobei ich Werte unter 70 nicht wollen würde, da wird schon die reine Wendigkeit auf einer Achse beschränkt.
Unter 66 meine ich würde auch der Trimmflug nicht mehr aktiv, da war früher auch mal was.
Aber vielleicht kann man ja mechanisch oder auch nur durch eine kleinere Anpassung grad so unter den Schwellwert (oder Schlappwert? Schlapp werd Wert?) kommen.
Grüßle
Eddi
Born to fly ...
forced to work.
JMalberg
26 March 2026 09:4826.03.2026 09:48
Hi Thomas
Show me some photos of the servo with servo horn in the middle and end positions so I can see the mechanical situation.
Regards, Jürgen
(Here are the missing commas for free use in my posts: ,,,,,,,,, )
Moin Thomas
zeig mal Fotos des Servos mit Servohorn in Mittel- und Endstellung um mal die mech. Gegebenheit zu sehen.
Gruß Jürgen
( hier noch die fehlenden Kommata zu freien Verwendung in meinen Beiträgen: ,,,,,,,,, )
thomas1130
26 March 2026 11:2526.03.2026 11:25
Quote: What do the values look like? Do you perhaps have the setup in your cloud so we can take a look?
Hi Eddi,
Yes - setup would be in the cloud - it's the OMP M6...
And yes - it is extremely rare in flight - it requires an "unfortunate combination" of coll & cycl - but it does happen sometimes.
At first I didn't know what was going on - the helicopter stopped briefly in the middle of its flight - and then cheerfully continued - that keeps the attention high ;-)
But since I don't want to compromise on either pitch or rotation rate, I just bought a new set of servos - I see it like Rainer - sometimes you're just "unlucky"..
They worked well in a Goblin - but the geometry is apparently "different" in the OMP - so it just doesn't work there...
Thanks for all the input here :-)
Best regards,
Thomas
(11006588)
Edited once. Last edited on 26.03.2026 at 11:25 by thomas1130.
Quote:wie sehen denn die Werte aus, hast Du das Setup ggfs. in Deiner Cloud so dass wir mal schauen können?
Hallo Eddi,
ja - Setup wäre in der Cloud - ist der OMP M6...
Und ja - es ist extrem selten im Flug - es muss schon eine "unglückliche Addition" von coll & cycl zusammenkommen - aber es passiert eben manchmal.
Zuerst wusste ich gar nicht was los ist - der Heli stoppt mitten im Flug kurz - und macht dann munter weiter - das hält die Aufmerksamkeit hoch ;-)
Aber da ich weder bei Pitch noch bei der Drehrate Kompromisse machen möchte, hab ich mir gerade einen neuen Satz Servos besorgt - ich seh das wie Rainer - da hat man halt "Pech"..
In einem Goblin haben sie gut funktioniert - bei OMP ist die Geometrie wohl "einen andere" - da geht sich das halt nicht aus...
THX für den vielen Input hier :-)
LG,
Thomas
(11006588)
1 mal bearbeitet. Zuletzt am 26.03.2026 11:25 von thomas1130.
Eddi E. aus G.
26 March 2026 12:2026.03.2026 12:20
Hi Thomas,
That's crazy if that's the case, the setup itself is OK with pitch -66...89 (but that also suggests a distorted geometry...), cyclic 83, there are trims with -42 but they're not exactly what would make the cup run over, CR 85.
However, if one could trim the servos closer to zero (move the servo arm), and then mechanically readjust the zero pitch via the linkage lengths if necessary, that could help... and is basically all that could be done meaningfully.
Or... the basic responsiveness of the leaves, for example, is rubbish; the VBar has to be significantly more involved with the OMP than with the Gobelin.
You're a good guy, you keep the economy going ^^ In that sense, you 'absolutely' have to buy a new VBar EVO VLink too, otherwise it won't work :-)
Grüßle
Eddi
Born to fly ...
forced to work.
Hi Thomas,
krass wenn's so ist, das Setup ist an sich OK mit Pitch –66...89 (spricht aber auch für eine verbogene Geometrie ...), zyklisch 83, da sind Trimms mit –42 zwar da aber auch nicht gerade was das Fass zum Überlaufen brächte, CR 85.
Wobei, wenn man halt die Servos näher an Null trimmen könnte (Servoarm versetzen), und über die Gestängelängen dann Null-Pitch nochmal mechanisch nachjustieren, falls nötig, könnte das helfen ... und ist eben eigentlich alles was man dann noch sinnvoll tun könnte.
Oder ... die Grundwendigkeit bspw. der Blätter ist Grütze, die VStabi muss beim OMP deutlich mehr reinlangen als beim Gobelin.
Bist 'n guter, hältst die Wirtschaft am Laufen ^^ in diesem Sinne, Du musst 'unbedingt' auch noch eine neue VStabi EVO VLink kaufen, sonst kann das nicht funktionieren :-)
Grüßle
Eddi
Born to fly ...
forced to work.
thomas1130
26 March 2026 12:4326.03.2026 12:43
Quote: However, if you could trim the servos closer to zero (move the servo arm), and then mechanically readjust the zero pitch via the linkage lengths if necessary, that could help... and is basically all that could be done meaningfully.
I tried that – "additional problem" – the JR horses have very few teeth – if I only move one tooth, I'm at about +15 on the trim – which then heals one side, but suddenly makes the other side a problem :-)
The only "solution" would be, as with my Graupner mc-24 "back in the day", the ability to set an electronic limit for individual servos AFTER all mixers per end point...
But this problem probably occurs too rarely :-)
Quote: You absolutely must also buy a new VBar EVO VLink, otherwise it won't work :-)
I just did that on the Rotor anyway - the heli still has a "V1 EVO with HK" - but that's not the problem, it works more than perfectly. 8-)
The new EVO is still waiting for a mechanic - maybe you'll deliver something one day after all 8-)
(But first, please send the small receiver - I really need it urgently)
Greetings from rainy Vienna,
Thomas
Edited twice. Last edited on March 26, 2026 at 12:56 PM by thomas1130.
Quote:Wobei, wenn man halt die Servos näher an Null trimmen könnte (Servoarm versetzen), und über die Gestängelängen dann Null-Pitch nochmal mechanisch nachjustieren, falls nötig, könnte das helfen ... und ist eben eigentlich alles was man dann noch sinnvoll tun könnte.
Das hab ich probiert - "Zusatzproblem" - die JR haben recht wenig Zähne - wenn ich nur einen Zahn versetze bin ich bei Trim ca +15 - was dann die eine Seite heilt, dafür plötzlich die andere Seite zum Problem werden lässt :-)
Einzige "Lösung" wäre wie "anno dazumal" bei meiner Graupner mc-24 die Möglichkeit, bei einzelnen Servos NACH allen Mischern pro Endausschlag noch ein elektronisches Limit setzen zu können...
Aber kommt wohl zu selten vor das Problem :-)
Quote:Du musst 'unbedingt' auch noch eine neue VStabi EVO VLink kaufen, sonst kann das nicht funktionieren :-)
Habe ich eh gerade auf der Rotor gemacht - der Heli hat ja noch eine "V1 EVO mit HK" - die aber ist nicht schuld, sondern funktioniert mehr als ausgezeichnet. 8-)
Neue EVO wartet noch auf eine Mechanik - vielleicht liefert ihr ja eines Tages doch noch wieder was 8-)
(Wobei bitte vorher noch den kleinen Empfänger - den bräuchte ich echt dringend)
LG aus dem verregneten Wien,
Thomas
2 mal bearbeitet. Zuletzt am 26.03.2026 12:56 von thomas1130.
Eddi E. aus G.
26 March 2026 13:1126.03.2026 13:11
Hey,
The problem was quite specific to JR. But even so, limiting an endpoint isn't such a good idea when three helicopters are supposed to work together. The helicopter might then jerk around or do something strange if the limit restricts a function (control or stabilization).
It is better to have the overall geometry such that the servos can operate freely within the range for which they are designed, without much electronic trimming, shortening, or lengthening of the range.
Add to that lightness, which shifts the pitch path in various ways, or the buck suppression, which might suddenly no longer suppress bucking because a servo feels its feelings are hurt...
If we were to chase after every shortcoming of components ^^
Grüßle
Eddi
Born to fly ...
forced to work.
Hej,
da Problem war ziemlich JR-spezifisch. Aber auch so ist einen Endpunkt limitieren keine so gute Idee, wenn drei zusammenarbeiten sollen. Dann schlägt der Heli ggfs. auch Haken oder macht was komisches, wenn die Begrenzung eben eine Funktion (gesteuert oder stabilisiert) begrenzt.
Besser ist, die Geometrie insgesamt so zu haben, dass die Servos innerhalb des Weges, für den sie konstruiert sind, frei arbeiten können, ohne viel elektronische Trimmung, Verkürzung, Verlängerung des Weges.
Nimm noch Leichtigkeit dazu, die auf verschiedene Weisen den Pitchweg verschiebt, oder die Aufbäum-Unterdrückung, die plötzlich das Aufbäumen nicht mehr unterdrücken könnte, weil ein Servo sich in seinen Gefühlen verletzt fühlt ...
Wenn wir jeder Unzulänglichkeit von Komponenten nachhecheln würden ^^
Grüßle
Eddi
Born to fly ...
forced to work.