JMalberg
7 April 2026 17:0407.04.2026 17:04
Hey everyone,
Today, April 7th, 2026, I received a message during intermediate landings (for setup) with two different helicopters indicating that the YGE Aureus 135 ESC was disconnected and would be reconnected within 2 seconds, which didn't actually happen. This is recorded in the log file in both cases, but the TM data in the graph shows no interruption in the power supply.
VBC SN 11003990 V2.1.125
VBAR 0027007157 04/07/2026 1:35:58 p.m
07.04.2026 13:43:59 Info; Speed controller switched to OFF
07.04.2026 13:43:59 Good; Motor switch Motor Off
07.04.2026 13:44:07 Good; VBackup in standby
07.04.2026 13:44:09 Good; YGE Controller Separated
07.04.2026 13:44:11 Good; YGE controller detected
07.04.2026 13:44:14 Good; Battery ID detected: 505F752D
and
VBAR 0027007095 07/04/2026 14:30:54
07.04.2026 14:48:27 Good; Motor switch Motor Off
07.04.2026 14:48:35 Good; VBackup in standby
07.04.2026 14:48:40 Good; YGE Controller Separated
07.04.2026 14:48:42 Good; YGE controller detected
07.04.2026 14:48:43 Good; Battery ID detected: A0327A2D
Regards, Jürgen
(Here are the missing commas for free use in my posts: ,,,,,,,,, )
Edited once. Last edited on 19.04.2026 at 15:45 by JMalberg.
Moin Leute,
ich hatte heute 7.4.2026 mit zwei unterschiedlichen Helis beim Zwischenlanden (zur Einstellung) eine Meldung dass der Regler YGE Aureus 135 getrennt und innerhalb von 2sec wieder angeschlossen wurde, was aber nicht passierte. In beiden Fällen steht das im Logfile, aber die TM-Daten im Graph zeigen keine Unterbrechung der Spannungsversorgung.
VBC SN 11003990 V2.1.125
VBAR 0027007157 07.04.2026 13:35:58
07.04.2026 13:43:59 Info;Drehzahlregler auf AUS geschaltet
07.04.2026 13:43:59 Gut;Motorschalter Motor Aus
07.04.2026 13:44:07 Gut;VBackup im Standby
07.04.2026 13:44:09 Gut;YGE Regler Getrennt
07.04.2026 13:44:11 Gut;YGE Regler erkannt
07.04.2026 13:44:14 Gut;Akku ID erkannt: 505F752D
und
VBAR 0027007095 07.04.2026 14:30:54
07.04.2026 14:48:27 Gut;Motorschalter Motor Aus
07.04.2026 14:48:35 Gut;VBackup im Standby
07.04.2026 14:48:40 Gut;YGE Regler Getrennt
07.04.2026 14:48:42 Gut;YGE Regler erkannt
07.04.2026 14:48:43 Gut;Akku ID erkannt: A0327A2D
Gruß Jürgen
( hier noch die fehlenden Kommata zu freien Verwendung in meinen Beiträgen: ,,,,,,,,, )
1 mal bearbeitet. Zuletzt am 19.04.2026 15:45 von JMalberg.
RV
7 April 2026 23:2907.04.2026 23:29
Hello Jürgen,
Perhaps that was a residual effect from the dev_Apps - I've cleaned it up, please update.
Another possibility is a near-field effect if the VBC is close to the model. The telemetry always transmits at full power – and it may have been overloaded.
Please test after the update and try to reproduce the issue if necessary.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Hallo Jürgen,
ev. war das noch ein Schmutzeffekt der dev_ Apps - habs bereinigt bitte mal updaten.
Was auch möglich wäre ist ein Nahfeld Effekt wenn die VBC nah am Modell ist. Die Telemetrie sendet immer volle Pulle - und ggf. hats übersteuert.
Bitte nach Update testen und ggf. versuchen zu reproduzieren.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
JMalberg
11 April 2026 15:0611.04.2026 15:06
Hi Rainer,
Yes, it was apparently leftover data from the DEV apps. There were no restarts on several flights now.
Regards, Jürgen
(Here are the missing commas for free use in my posts: ,,,,,,,,, )
Hai Rainer,
jo , es waren offenbar Überbleibsel von den DEV-Apps. Es war jetzt in mehreren Flügen keine Neustarts.
Gruß Jürgen
( hier noch die fehlenden Kommata zu freien Verwendung in meinen Beiträgen: ,,,,,,,,, )
JMalberg
18 April 2026 23:2618.04.2026 23:26
Good morning,
No, not leftovers... seems to be a YGE error.
The helicopter with VBAR 0027007157 has a YGE Aureus 135 installed which was updated to the current firmware after the restart error on 07.04.2026 13:35:58.
The helicopter (Chinook) has a YGE Aureus 135 installed, which does not have the latest firmware.
VBAR 0027007095 04/18/2026 12:54:57
18.04.2026 13:04:47 Good; VBackup in standby
18.04.2026 13:04:53 Good; YGE Controller Separated
18.04.2026 13:04:55 Good; Engine switch Idle Start
18.04.2026 13:04:55 Good; Backup connected, cap: 6.0V
18.04.2026 13:04:55 Info; Speed controller switched ON
18.04.2026 13:04:55 Good; Motor switch Motor On
18.04.2026 13:04:55 Good; YGE controller detected
18.04.2026 13:04:56 Good; Battery ID detected: A0327A2D
18.04.2026 13:04:56 Good; Battery data from VBC: 16 BONKA 5200 202401
18.04.2026 13:04:56 Warning; Battery not full! Full: 50.4V Current: 45.4V
18.04.2026 13:04:59 Info; Speed controller switched to idle
18.04.2026 13:04:59 Good; Engine switch Idle Start
18.04.2026 13:04:59 Info; Speed controller switched to OFF
18.04.2026 13:04:59 Good; Motor switch Motor Off
04/18/2026 1:04:59 PM Info;Off - Controller - Umin:45.4V Imax:0.5A Temp:52?
18.04.2026 13:05:07 Good; Backup in standby
18.04.2026 13:05:37 Good;VBackup connected, cap:6.0V
18.04.2026 13:05:48 Good; VBackup in standby
The error only occurs when the battery is at approximately 30% (VBAR battery%) or less.
I will also update this YGE and then report back.
Regards, Jürgen
(Here are the missing commas for free use in my posts: ,,,,,,,,, )
Edited once. Last edited on 18.04.2026 at 23:28 by JMalberg.
Moin,
nee doch nicht Überbleibsel... scheint ein YGE-Fehler zu sein
Im Heli mit VBAR 0027007157 ist ein YGE Aureus 135 verbaut der nach dem Neustartfehler am 07.04.2026 13:35:58 auf die aktuelle Firmware aktualisiert wurde.
In dem Heli (Chinook) ist ein YGE Aureus 135 verbaut, der nicht die aktuelle Firmware hat.
VBAR 0027007095 18.04.2026 12:54:57
18.04.2026 13:04:47 Gut;VBackup im Standby
18.04.2026 13:04:53 Gut;YGE Regler Getrennt
18.04.2026 13:04:55 Gut;Motorschalter Leerlauf Durchstarten
18.04.2026 13:04:55 Gut;VBackup verbunden, cap:6.0V
18.04.2026 13:04:55 Info;Drehzahlregler auf AN geschaltet
18.04.2026 13:04:55 Gut;Motorschalter Motor An
18.04.2026 13:04:55 Gut;YGE Regler erkannt
18.04.2026 13:04:56 Gut;Akku ID erkannt: A0327A2D
18.04.2026 13:04:56 Gut;Akkudaten von VBC: 16 BONKA 5200 202401
18.04.2026 13:04:56 Warn;Akku nicht voll! Voll: 50.4V Akt.: 45.4V
18.04.2026 13:04:59 Info;Drehzahlregler auf Idle geschaltet
18.04.2026 13:04:59 Gut;Motorschalter Leerlauf Durchstarten
18.04.2026 13:04:59 Info;Drehzahlregler auf AUS geschaltet
18.04.2026 13:04:59 Gut;Motorschalter Motor Aus
18.04.2026 13:04:59 Info;Aus - Regler - Umin:45.4V Imax:0.5A Temp:52?
18.04.2026 13:05:07 Gut;VBackup im Standby
18.04.2026 13:05:37 Gut;VBackup verbunden, cap:6.0V
18.04.2026 13:05:48 Gut;VBackup im Standby
Der Fehler tritt auch nur auf wenn der Akku nur noch auf ca 30% (VBAR-Akku%) und weniger ist.
Ich werde auch diesen YGE aktualisieren und berichte dann weiter
Gruß Jürgen
( hier noch die fehlenden Kommata zu freien Verwendung in meinen Beiträgen: ,,,,,,,,, )
1 mal bearbeitet. Zuletzt am 18.04.2026 23:28 von JMalberg.
JMalberg
19 April 2026 15:4419.04.2026 15:44
It's been dealt with.
It's a YGE problem.
https://www.yge.de/service/ Firmware from V1.03596
Quote:
YGE In rare cases, the controller could ONLY restart after the flight and the engine had been switched off. This has been fixed.
Regards, Jürgen
(Here are the missing commas for free use in my posts: ,,,,,,,,, )
Hat sich erledigt.
Es ist ein YGE-Problem
https://www.yge.de/service/
Firmware ab V1.03596
Quote:
YGE
In seltenen Fällen konnte es NUR (!!) nach dem Flug und Abstellen des Motors zu einem Restart des Reglers kommen. Dies wurde behoben
Gruß Jürgen
( hier noch die fehlenden Kommata zu freien Verwendung in meinen Beiträgen: ,,,,,,,,, )
RV
19 April 2026 15:5619.04.2026 15:56
Thanks for the info, Jürgen!
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Danke für die Info Jürgen!
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.