Danny
27 April 2026 18:4027.04.2026 18:40
Hello everyone, I have the following problem:
Evo is new and this is the first time I've used it on a helicopter. After activating it three times, I already had a cold start reset while locked, and now it simply switched off during operation. Power was supplied.
Even if the controller were no longer supplying power, the power capacitor is connected and active. After a restart, everything works normally again. In the lock screen where the Evo simply switched off, the last message displayed was "HW controller disconnected".
The controller is a Hobbywing 200A BEC with the latest Vbar software; the controller ran without problems in the old heli with Vstabi Silverline.
Thankfully this happened during the setup work and not in flight.
I made a video of it, can I upload it here?
LG
Danny
Hallo zusammen folgendes Problem:
Evo ist neu und zum erstmals auf einem Heli, nach dem 3 aktivieren hate ich im Lock schon einen Kaltstart Resetgrunt Power on und jetzt ist es im Betrieb einfach ausgegangen. Stromversorgung war da,
auch wenn der Regler nicht mehr liefern würde Powercap ist angeschlossen und aktiv. Nach Neustart läuft alles wieder normal. Im Lock wo das Evo einfach ausgegangen ist steht als letztes HW Regler getrennt.
Regler ist ein Hobbywing 200A BEC mit der Letzten Software Vbar, der Regler lief ohne Probleme im alten Heli mit Vstabi Silverline.
Dies ist Gott sei dank bei den Einstellarbeiten passiert und nicht im Flug.
Ich habe ein Video davon gemacht, kann ich das hier Hochladen?
LG
Danny
RV
27 April 2026 18:4227.04.2026 18:42
Nope - video isn't possible here, please use one of the usual hosters and link it here.
But... what are the serial numbers of the VBar Control and the stabilizer bar?
Are the logs in the cloud?
How is the controller connected?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Nope - Video geht hier nicht, nimm dazu bitte einen der üblichen Hoster und verlinke es hier.
Aber ... welche Seriennummer haben denn die VBar Control und die Stabi dazu?
Sind die Logs in der Cloud?
Wie ist der Regler angeschlossen?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Danny
27 April 2026 18:5127.04.2026 18:51
Hello dear Rainer,
Everything should be in the cloud.
Evo 0027009827
Control EVO 11007239 2.1.125
I'll upload it to Y and then link it.
I tried another Evo of mine, and that one runs without errors.
LG
Danny
Hallo lieber Rainer,
sollte alles in der Cloud sein
Evo 0027009827
Control EVO 11007239 2.1.125
Werde das bei Y hochladen und dan verlinken.
Habe mal ein anderes Evo von mir versucht, dass läuft ohne Fehler.
LG
Danny
Danny
27 April 2026 19:1027.04.2026 19:10
RV
27 April 2026 20:0027.04.2026 20:00
Hmm... Video not available ;-(
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Hmm ... Video nicht verfügbar ;-(
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Fingolf
27 April 2026 20:2527.04.2026 20:25
It is set to private.
Ist auf privat eingestellt
Danny
27 April 2026 20:3727.04.2026 20:37
So now Y has also turned out badly, I miss the RC movie.
https://m.youtube.com/shorts/JycpLJ2jJJA
So jetzt Y ist auch schlecht geworden, ich vermisse RC movie
https://m.youtube.com/shorts/JycpLJ2jJJA
RV
27 April 2026 22:3427.04.2026 22:34
Question - it's not so easy to see in the video:
How and what is connected to the stabilizer at the top of the RPM unit?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Frage - man siehts im Video nicht so gut:
Wie und was ist am RPM oben an der Stabi angeschlossen?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Danny
28 April 2026 18:5428.04.2026 18:54
The RPM sensor wire from the ESC is plugged in there, of course to the signal input.
Perhaps I should elaborate a little further.
1. Starting the Evo setup, adjusting sensor alignment, servo direction, tail servo frequency, servo function test, BEC supply checked, voltage drops of approx. 0.02-0.08 V during rapid movement of all servos.
2. Telemetry test ESC, battery setup, motor test rotation direction and RPM display all OK.
3. Exit servo trim settings setup, transmitter switched off, 5 seconds later cold start (servo initialization sugar)
4 or 5 S, I'm not sure anymore, opened setup, opened servo trim, bam, EVO off. Disconnected battery, removed power cap, reconnected battery, EVO on again.
After disconnecting the battery, the Evo continued to run, powered by the voltage of the power cap, until it was manually switched off, except where it switched off. The power cap was active here, as can be seen in the video.
Everything is now OK with the other EVO, without any errors.
LG
Danny
Dort ist die Sensorleitung RPM vom ESC eingesteckt natürlich auf Signal Eingang,
vielleicht hole ich noch mal ein bisschen weiter aus.
1. Start der Evo einstellarbeiten im Setup Sensor Ausrichtung, Servo Richtung, Heckservo Frequenz, Funktionstest Servos, BEC-Versorgung angeschaut bei schneller Bewegung aller Servos Einbrüche um ca. 0,02- 0,08 V .
2. S. Telemetrie Test ESC, Akku einstellen, Motor Test Drehrichtung und RPM-Anzeige alles OK.
3. S. Servo Trim Einstellungen Setup verlassen Funke abgestellt, 5 Sek später Kaltstart (Servo Initialisierung Zucker)
4. Oder 5 S. bin mir nicht mehr sicher, Setup geöffnet Servo Trim aufgemacht zack EVO aus. Akku ab Powercap aus Akku wieder dran Evo wieder an.
Nach abziehen des Akkus lief der Evo weiter, versorg durch die Spannung des Powercap, bis zur manuellen Abschaltung außer bei da wo er ausgegangen ist Powercap war hier ja aktiv wie auf dem Video zu sehen.
Mit dem anderen EVO jetzt alles IO ohne Fehler.
LG
Danny
RV
28 April 2026 21:1928.04.2026 21:19
Quote: The RPM sensor wire from the ESC is plugged in there, of course to the signal input.
Perhaps I should elaborate a little further.
And that's ONLY the pulse? Nothing else? - In the video, it looks to me like there's an orange wire on the negative pin...
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Quote:Dort ist die Sensorleitung RPM vom ESC eingesteckt natürlich auf Signal Eingang,
vielleicht hole ich noch mal ein bisschen weiter aus.
Und da ist NUR der Puls drauf? Nichts anderes? - Mir scheint es im Video so dass da eine orangene Leitung auf dem Minuspin wäre ...
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Danny
29 April 2026 17:3029.04.2026 17:30
Neither pulse nor minus, here's another screenshot from the video.
What you're referring to is the signal wire from the tail servo which is plugged into the tail, and the other yellow wire next to it is the signal wire from servo CH 1 which is plugged into CH 1. The RPM cable from the controller only has one yellow wire and that is connected to the RPM signal on the EVO.
LG
Danny
Edited once. Last edited on 29.04.2026 at 17:37 by Danny.
Weder Puls noch Minus, hier noch mal ein Screenshot aus dem Video.
Das was du meinst ist die Signalleitung vom Heckservo was in Tail eingesteckt ist und das andre gelbe Kabel daneben ist die Signalleitung vom Servo CH 1 was in CH 1 angesteckt ist, der RPM-Kabel vom Regler hat nur eine Leitung in Gelb und die ist am Signal RPM am EVO angeschlossen.
LG
Danny
1 mal bearbeitet. Zuletzt am 29.04.2026 17:37 von Danny.
RV
29 April 2026 21:5229.04.2026 21:52
Well - I had already taken a screenshot, but I wasn't sure how it was filmed from that perspective.
So, just to be safe, I would double-check the voltage at a servo slot with a multimeter if it happens.
And also try it without the YGE TELE plug.
Let me know!
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Naja - einen Screenshot hatte ich auch schon gemacht, war mit aber nicht sicher aus der Perspektive wie gefilt wurde.
Also - ich würde nochmals zur Sicherheit mit einem Multimeter an einem Servoslot die Spannung nachmessen wenns passiert.
Und auch mal ohne den YGE TELE Stecker probieren.
Sag Bescheid!
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Eddi E. aus G.
30 April 2026 08:5630.04.2026 08:56
Good morning,
I would also start again from the beginning, perhaps with the stabilizer connected only to the receiver battery, then with the stabilizer connected to the receiver battery and servos, then with the buffer connected, then from the BEC, first without, then with RPM, and do the same with telemetry. For simplicity, connect everything in reverse order: first RPM, then telemetry, then battery instead of BEC, buffer removed, etc. When it stops at a certain point, you've found it.
Grüßle
Eddi
Born to fly ...
forced to work.
Moin,
ich würde ggfs. auch nochmal weiter vorn anfangen, Stabi nur mit Empfängerakku, Stabi mit Empfängerakku und Servos, dann mit Puffer, dann vom BEC, erst ohne dann mit RPM, selbes mit Telemetrie. Der Einfachheit halber rückwärts abstecken, erst RPM, TELE, dann statt BEC Akku, Puffer weg, ... wenn's an einem Punkt aufhört, ... gefunden.
Grüßle
Eddi
Born to fly ...
forced to work.
Danny
3 May 2026 18:3403.05.2026 18:34
Hello everyone,
Sorry for the late reply. As I mentioned, the problem isn't with the other components; everything works perfectly with a different EVO. I even went flying this past weekend. With the replacement EVO, there are no more issues, neither during setup nor while flying.
I contacted the dealer about an exchange/complaint; how do I get my purchased Pro software installed on the new EVO when it arrives?
Best regards, Danny
Edited once. Last edited on 03/05/2026 at 18:36 by Danny.
Hallo zusammen,
Sorry das ich mich erst jetzt melde, wie schon geschrieben an den anderen Komponenten liegt es nicht mit andrem EVO läuft alles ohne Probleme, jetzt am WE fliegen gewesen. Mit dem tausch EVO keine Auffälligkeiten mehr weder beim einstellen noch beim Fliegen.
Habe den Händler angeschrieben zum Austausch/Reklamation, wie bekomme ich denn, wenn das neue EVO da ist meine gekaufte Pro Software da drauf?
LG Danny
1 mal bearbeitet. Zuletzt am 03.05.2026 18:36 von Danny.
RV
3 May 2026 22:2703.05.2026 22:27
Please create a service case for this VBar.
To do this, log in to vstabi.info and navigate to your device list (bottom left). Click on the service icon next to the relevant device.
Please fill out the form (first contact details, then a description of the problem). You can also attach images, logs, etc. If it's a warranty claim, please upload your purchase invoice.
After submitting the form, a confirmation email will be sent automatically.
Our service will then contact you via email as soon as possible.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Bitte lege für diese VStabi einen Servicefall an.
Logge Dich dazu auf vstabi.info ein und navigiere zu Deiner Geräteliste (links unten). Klicke auf das Service Icon beim betreffenden Gerät.
Das Formular (Zuerst Kontaktdaten, im 2. Schritt Fehlerbeschreibung) bitte ausfüllen. Hier kann man auch Bilder, Logs o.Ä. anhängen. Im Falle einer Gewährleistungsanfrage bitte die Kaufrechnung mit hochladen.
Nach Absenden des Formulars wird automatisch eine Bestätigungsmail versandt.
Unser Service nimmt dann so bald wie möglich per Mail Kontakt auf.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Danny
16 May 2026 18:5616.05.2026 18:56
Hello everyone,
The VBar was replaced, and I received a code for the V8 upgrade.
The service technician was unable to reproduce the error; at my request, the stabilizer was replaced and I received a new one.
Many thanks to the Mikado team for the service and support, thumbs up.
The replaced device works perfectly.
BG
Danny
Hallo zusammen,
V-stabi wurde getauscht, und ich habe einen Code für das V8 Upgrade bekommen.
Der Service Techniker hat den Fehler nicht Reproduzieren könne, auf Wunsch wurde der Stabi gehtauscht und ich habe einen neuen bekommen.
Vielen Dank für den Service und Support an das Mikado Team, Daumen rauf.
Getauschtes Gerat funktioniert einwandfrei.
BG
Danny