← VBar NEO/EVO VLink

Strange crash - cause? translated

VBar › VBar NEO/EVO VLink · Started by martin_fuerst on 22 May 2026 13:5922.05.2026 13:59
martin_fuerst 22 May 2026 13:5922.05.2026 13:59
Hello,

I had an unpleasant experience today on my second flight with my
Logo 550SX.

The helicopter was no longer controllable and was doing something like piroflips, if you don't already know how to do them.
- the feeling was modest...

Stability number: 0027002712 Flight: 22.05.2026 10:58:31

Could you please check if you can find anything in the (radio) log - I don't see anything.
Now everything is at ground level.

LG
Martin



Edited twice. Last edited on 22.05.2026 at 18:45 by martin_fuerst.
machine-translated from German · Show original
Eddi E. aus G. 22 May 2026 14:1022.05.2026 14:10
Hi Martin,

In my opinion, it looks inconspicuous, as does the radio.

Power on, the usual entries, bank switching (presumably settings adjusted), one flight, motor off, settings again?, another flight, the only noticeable thing (if it's the right log?) is the YGE current limit, but only one second before powering off.
The log ends normally.

Approximately when (in terms of time) in the flight/log did this occur?

I would guess it's a mechanical or electrical issue; everything seems to have been OK with the stabilizer the whole time.

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
martin_fuerst 22 May 2026 16:1322.05.2026 16:13
The last flight of the Logo550 in the cloud ended in a crash - but I/you can't see that in the log!
I completely rebuilt the mechanics 2-3 weeks ago, carefully and without any issues - including a new YGE Saphir 125 V3 and the backup buffer I bought from you at RotorLive.
The TS servos were used but unremarkable BLS471s, and at the rear a new MKS990.
----
Prehistory:
I had the new EVO installed in the spring instead of a NEO and then experienced a kind of shutdown
(There was nothing in the log and nothing in the controller log either) came down roughly.
I rebuilt everything from a "spare parts kit" with a new controller and buffer, and today...
First flight completed...



Edited once. Last edited on 22.05.2026 at 16:14 by martin_fuerst.
machine-translated from German · Show original
thomas1130 22 May 2026 17:3522.05.2026 17:35
Quick question:

"Grounding" - meaning you've installed a well-conducting connection from the tail rotor to the motor plate - and you've also measured it??

LG
machine-translated from German · Show original
martin_fuerst 22 May 2026 18:2122.05.2026 18:21
thomas1130 wrote:
-------------------------------------------------------
> Quick question:
>
> "Grounding" - that is, a well-conducting connection from the
> You have installed the tail rotor up to the motor plate -
> and also measured??
>
> LG

Yes, Thomas is installed and I even measured it - I was really "overly precise".
during construction. That's what's particularly annoying me right now...



Edited twice. Last edited on 22.05.2026 at 22:28 by martin_fuerst.
machine-translated from German · Show original
martin_fuerst 22 May 2026 18:5022.05.2026 18:50
Just a thought from me:
Could you be so kind as to check if my EVO possibly...
It has the "old" sensor installed - I don't see any adhesive inside.
No.: 27002712

Thanks!



Edited once. Last edited on 22.05.2026 at 18:50 by martin_fuerst.
machine-translated from German · Show original
Eddi E. aus G. 27 May 2026 09:5127.05.2026 09:51
Good morning,

No, that serial number has the new sensor. The transition was in October 2023, around serial numbers 27001950-27002000... it's worth asking in that range; all < have the first generation sensor, all > the new one, and from 27001270 onwards they are glued in place at the factory.

Grüßle

Eddi

Born to fly ...
forced to work.
machine-translated from German · Show original
martin_fuerst 27 May 2026 20:3427.05.2026 20:34
Thanks for the information - that means I can mentally cross that off my list.

LG
Martin
machine-translated from German · Show original
martin_fuerst 18 June 2026 13:4318.06.2026 13:43
Update:
99.9% self-inflicted, not due to technology.

The screw of the tail pressure roller had completely slipped out during flight.
because I apparently hadn't screwed the stop nut in properly.
The result was the destruction of the control joints of the tail rotor blade holders,
because I was just about to have a full-blown right-sided rash and in half a year
It was a flip. It wasn't a typical, recognizable rear-end defect to me.
(circling) and it happened very quickly - a tail blade probably tried to do that for a moment.
He was trying to do his job, and I was overwhelmed by the timing.

LG
Martin



Edited once. Last edited on 18.06.2026 at 13:44 by martin_fuerst.
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless