Tgilf
22 June 2026 06:5022.06.2026 06:50
Hello everyone - I'd like to ask for some advice again.
Yesterday, when I increased the engine speed to 2600rpm (Bank 3) on my OMP M4 Max with the Vbar Evo, the following happened:
After full pitch and leveling, the tail started to oscillate rapidly and frighteningly. I reduced the engine speed and frantically pressed the emergency brake. Then it was stable again. Safe landing.
Is this a mechanical issue or a setting? I've never experienced this behavior at lower RPMs.
Thank you all and best regards
Tom
Hallo zusammen - ich bitte nochmal um einen Rat.
Bei meinem OMP M4 Max mit dem Vbar Evo kam es gestern bei Erhöhung der Drehzahl auf 2600rpm (Bank 3)
nach vollem Pitch und wieder waagerechter Ausrichtung zu einem gruseligen schnellen Pendeln des Hecks. Ich habe die Drehzahl reduziert und panisch Rettung gedrückt. Dann ging es wieder. Sicher gelandet.
Ist das etwas mechanisches oder eine Einstellung? Auf niedrigeren Drehzahlen hatte ich das Verhalten noch nie.
Danke euch und viele Grüße
Tom
RV
22 June 2026 07:2022.06.2026 07:20
Hmmm... if someone used a rescue service, it must have been more than just "shuttle-shuttle", right?
Which tail servo is installed, and what are its control frequencies and sensitivities?
Could the tail servo have overheated?
And which version is installed on the stabilizer? Vx.y?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Hmmm ... wenn man Rettung benutzt muss das doch was mehr als "Pendeln" gewesen sein, oder?
Welches Heckservo ist denn verbaut und welche Regelfrequenz sowie Empfindlichkeiten?
Wurde ggf. das Heckservo zu heiß?
Und welche Version ist auf der Stabi drauf? Vx.y?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Tgilf
22 June 2026 08:5822.06.2026 08:58
Yes. It was more than just commuting; it looked pretty wild...
The tail servo is the OMP DS3515T with 560Hz, I think I selected it as 500Hz in the configuration because 560Hz wasn't available....
I find that the rear servo always gets very warm.
The version on the stabilization software is from before the last update, I think it's 8.2 - but I'll double-check later if that helps you.
Thank you!!
Ja. Es war etwas mehr als nur pendeln sah schon ziemlich wild aus...
Heckservo das OMP DS3515T mit 560Hz glaube ich hatte es auf 500Hz ausgewählt in der Konfiguration weil es 560 nicht gab....
Das Heckservo wird schon immer sehr warm finde ich.
Auf der Stabi ist die Version vor dem letzten Update 8.2 glaube ich - ich schaue aber nachher nochmal genau nach wenn es dir weiter hilft.
Vielen Dank!!
Tgilf
22 June 2026 16:5022.06.2026 16:50
I checked again. I've set it to 500Hz and 760µs.
The tail servo gets warm even when stationary. The swashplate servos don't…
V8.2 is installed.
Can you deduce anything from that, Rainer?
One more thing
I'm using the Vstabi governor. I read that with direct drive, you should set the sensitivity of the speed controller to 10. Is that correct?
Edited once. Last edited on 22.06.2026 at 17:06 by Tgilf.
Habe nochmal geschaut. 500Hz und 760us habe ich eingestellt.
Der heckservo wird schon im Stand warm. Die TS Servos nicht….
V8.2 ist installiert.
Kannst du da etwas draus herleiten Rainer?
Noch etwas
Ich nutze den Vstabi governor. Habe gelesen das man beim direkt Antrieb die Empfindlichkeit auf 10 stellen soll vom Drehzahlregler. Ist denn so?
1 mal bearbeitet. Zuletzt am 22.06.2026 17:06 von Tgilf.
RV
22 June 2026 17:4322.06.2026 17:43
Yeah - 10 Gain is okay for now.
Regarding the servo – servos tend to become slightly less powerful (protective mechanism) when they get hot. This overheating is sometimes exacerbated by the fact that even the smallest vibrations are picked up by the tail sensor and then transmitted to the servo at high speed.
Try 333 Hz for comparison, maybe that will be enough.
If that is sufficient - and the vibration analysis is "clean" - the above would be correct.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Jou - 10 Gain ist erstmal ok.
Wegen Servo - die Servos werden gerne mal etwas kraftloser (Schutzmechanismus) wenn sie heiß werden. Das heißwerden wird u.U. dadurch begünstigt dass kleinste Vibrationen vom Hecksensor aufgenommen werden und dann mit hoher Geschwindigkeit ans Servo gehen.
Probiere mal 333 Hz zum Vergleich aus, vielleicht reicht das schon.
Wenn das reicht - und die Vibrationsanalyse "sauber" ist - wäre das obige zutreffend.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Tgilf
22 June 2026 17:5422.06.2026 17:54
Thanks! I'll test it.
Danke! Ich teste es.
Max8200
22 June 2026 17:5522.06.2026 17:55
Unfortunately, I can't help you directly with that, but my M4 had terrible problems with the rear end (there's a thread about troubleshooting here and "next door").
After I replaced the tail servo twice, the helicopter was set up by Daniel Wiedenmann, and then everything was fine for a while. Since then, I've flown about 50 battery packs, and the tail oscillation in hover flight is back, even though NOTHING has been changed.
The rear end also no longer locks into place as cleanly as after the adjustment.
My tail servo doesn't get hot at all. Not even warm. However, the T/S servos get quite warm after running through three batteries at once.
I'll tackle that next week, and if I make any progress, I'll let you know here :-)
Best regards,
Lars
Ich kann dir da leider nicht direkt helfen, aber mein M4 hatte unsägliche Probleme mit dem Heck (gibts hier und "nebenan" nen Beitrag zur Fehlersuche).
Der Heli ist dann nachdem ich zwei mal das Heckservo gewechselt habe von Daniel Wiedenmann eingestellt worden, dann war erst mal Ruhe im Karton. Mittlerweile hab ich seit dem ca 50 Akkus geflogen und das Heckpendeln im Schwebeflug ist wieder da obwohl NICHTS verändert wurde.
Ebenfalls rastet das Heck nicht mehr so sauber ein wie nach der Einstellerei.
Heiss wird mein Heckservo jedoch nicht. Nichtmal warm. Dafür sind die T/S Servos nach 3 Akkus "ballern" ordentlich warm.
Ich begebe mich da nächste Woche mal ran, falls ich was erreiche lasse ich es dich hier wissen :-)
Viele Grüße,
Lars
Tgilf
22 June 2026 21:0622.06.2026 21:06
Thank you!!
Vielen Dank!!