Chriss
23 June 2026 22:4023.06.2026 22:40
Hello,
Is it possible to actively bind two EVOS devices to one transmitter?
Why the question...?
If I power the servos with an ESC BEC, for example, 8V BEC
And if I want special functions that require a lot of power, it would make sense not to run them through the ESC BEC. Instead, I would use an external BEC, e.g., 12V, so that flight and special functions are cleanly separated.
Thank you. Kind regards.
Hallo,
ist es möglich eine 2 EVOS aktiv an einen Sender zu binden ?
Warum die Frage....?
Wenn ich mit ESC BEC, die Servos versorge BEC zb. 8V
Und ich Sonderfunktionen haben möchte die viel Strom brauchen, wäre es doch sinvoll das nicht mit über den ESC BEC laufen zu lassen. Sondern ein externes BEC zb. 12v , so das Flitght und Sonderfunktionen sauber getrennt sind.
Dankeschön Freundlicher Gruß
RV
23 June 2026 23:0223.06.2026 23:02
https://www.vstabi.info/de/rx2_de
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
https://www.vstabi.info/de/rx2_de
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Chriss
24 June 2026 12:1124.06.2026 12:11
Does this also work perfectly with the RX Only receiver?
Kind regards
Prima geht das auch mit den RX Only Empfänger ?
Freundlicher Gruß
Eddi E. aus G.
24 June 2026 13:4724.06.2026 13:47
Good morning,
Nope, or not useful.
The RX-2 firmware (Secondary Receiver) was specifically designed to allow two receivers to remain bound in parallel, and to enable management/configuration of the transmitter, and it is part of the software package for VBasic (or other EVO).
Theoretically, it's probably possible to bind a second receiver RX-Only (every time it's switched on) and configure it accordingly, but that remains what it is: a makeshift solution or, more accurately, a silly coincidence.
Grüßle
Eddi
Born to fly ...
forced to work.
Moin,
nope, oder nicht sinnvoll.
Die RX-2-Firmware (Secondary Receiver, 2. Empfänger) wurde speziell dafür entwickelt, dass zwei Empfänger parallel gebunden bleiben können, und dass man den entsprechend im Sender verwalten/einstellen kann, und sie ist Bestandteil des Software-Pakets für VBasic (oder andere EVO).
Man kann theopraktisch vermutlich einen 2. Empfänger RX-Only binden (bei jedem Einschalten erneut), und den entsprechend konfigurieren, aber das bleibt eben was es ist, eine Notlösung oder eigentlich ein dummer Zufall.
Grüßle
Eddi
Born to fly ...
forced to work.
Chriss
26 June 2026 06:3026.06.2026 06:30
Hello,
I installed the RX-2 firmware (Secondary Receiver) on an Evo via PC.
The app is also active on the EVO transmitter.
EVO with RX-2 firmware (Secondary Receiver, 2nd receiver) can be bound, it works.
INI setup completed.
But after power off/on, the RX-2 firmware (Secondary Receiver, 2nd receiver) must be updated every time.
It needs to be re-bound. The LED flashes rapidly red/green.
Thank you. Kind regards.
Hallo,
habe die RX-2-Firmware (Secondary Receiver, 2. Empfänger) auf einer Evo via PC installiert.
Auf den Sender EVO ist auch die App. aktiv.
EVO mit RX-2-Firmware (Secondary Receiver, 2. Empfänger) läßt sich binden, geht auch.
Ini setup gemacht.
Aber nach Power off/on muß jedesmal die RX-2-Firmware (Secondary Receiver, 2. Empfänger),
neu gebunden werden. LED blinkt schnell rot/grün .
Dankeschön Freundlicher Gruß
Eddi E. aus G.
26 June 2026 09:3326.06.2026 09:33
Good morning,
I can't confirm that, I just tested it.
An already bound EVO RX2 connects like any other receiver as soon as it is switched on (even if the primary receiver is _not_ switched on), and the menu item > Additional Receiver (RX2) appears in the menu (app loaded and active).
Grüßle
Eddi
Born to fly ...
forced to work.
Moin,
kann ich so nicht bestätigen, gerade getestet.
Ein bereits gebundener EVO RX2 verbindet sich wie jeder andere Empfänger auch, sobald er eingeschaltet wird (selbst wenn der primäre Empfänger _nicht_ eingeschaltet ist), und im Menü taucht der Menüpunkt > Zusätzlicher Empfänger (RX2) auf (App geladen und aktiv).
Grüßle
Eddi
Born to fly ...
forced to work.
Fingolf
26 June 2026 17:4426.06.2026 17:44
Is the power supply adequate? But as Eddie writes, it's the same for me.
Passt die Stromversorgung? Aber wie Eddie schreibt, geht bei mir genauso.